Is there an issue with my 2002 C240?

I have a 2002 C240 and I’ve recently had an issue while driving. I’ve read similar posts to this one but someone always writes their own issues that are different from this matter.

When does a car engine stall while driving?

The stalling only occurs when the engine has reached operating temperature (15-20 min driving). It stalls very quietly with NO jerking, shaking, surging or choking. It seems as soon as driver foot leaves the accelerator paddle, at low speed, the engine stalls.

Why does my car stall in the Cold?

If you’re having the same problem as you did in the cold, only your engine is warm, even hot, this could indicate the following problems: If you have a carburetor, you may have a bad accelerator pump or power circuit. The Fix: Replace accelerator pump or replace the carburetor. There may be a vacuum leak.

What does it mean when a car engine hesitates?

This is what it means when the car engine hesitates. It is usually the result of a problem with the air and fuel mixture within the combustion chamber. However, there is a long list of other reasons which could be the cause of this hesitation problem too.

Why does my transmission have a hard shifting problem?

You would be surprised to know that the majority of the transmissions problems such as hard shifting and no shifting issues come from incorrect transmission fluid level or the infamous transmission 13 pin connector plug O-ring. These are easy fixes that you can even tackle yourself.

When does the engine stall in a Mercedes?

There are never any notifications on the dash or any signs of it beginning to fail. This typically happens when I’m slowing down at an intersection or just driving slower in traffic.

What to do if your engine stall at idle?

There are similar posts explaining the symptoms and various cures like Mass Air Flow Sensor, Idle Air Control/valve, fuel pressure regulator, and a crankshaft positioning sensor however I was told that the Idle Air control valve is working fine, and the CPS wouldn’t work after it has failed.

What causes a car to run strange at idle?

You know I been using alot MAF for my testing and found that bad MAF will cause the car run stranged eg. engine rev up and down unintention and also the fuel consumption is bad. The gear shift is rough. After I change to the good MAF one, the car run normally again.

Why does my Mercedes C class run rough off-idle?

21 people found this helpful. Hmmm, so what you’re saying is it idles ruff but passed that part of the test and runs smooth off-idle but fails that part because it’s running too rich ( too much fuel). If you had a vacuum leak at the throttle body you’ll be running lean not rich as you are now.

Why is my Mercedes C class engine not working?

One Mercedes specialist told be that my cars engine is a gonner and the timing chain and gears were also damaged. Another one told us that our ECU was faulty and then suddenly there was no pressure on the one valve and so the so-called list of difference diagnosis started.

I have a 2002 C240 and I’ve recently had an issue while driving. I’ve read similar posts to this one but someone always writes their own issues that are different from this matter.

How does a Cisco C240 M4 server work?

With the server fully pushed into the slide rails, open a hinged slam latch lever on the front of the server and insert the screw through the hole that is under the lever. The screw threads into the static part of the rail on the rack post and prevents the server from being pulled out.

Where is the CMA located on a C240 server?

The CMA is shipped assembled for installation to the rear of the right-hand slide rails (when facing the rear of the server). The CMA is reversible so that you can mount it to the rear of either the right or left slide rails. However, you must remove and reposition the CMA tabs so that the hinges open correctly.

What kind of rail kit do I need for C240 server?

This server supports one rail kit option: Cisco part UCSC-RAILB-M4= (ball-bearing rail kit). Do not attempt to use a rail kit that was for the Cisco UCS C240 M3 server; the rail kit for the Cisco UCS C240 M4 server has been designed specifically for it. The slide rails for this server have an adjustment range of 26 to 36 inches (660 to 914 mm).

Can a Mercedes Benz mass air flow sensor be replaced?

Some of the most common symptoms of a bad Mass Air Flow sensor in Mercedes Benz cars are: Engine dies, stalls soon after you start it. Sometimes cleaning the sensor could help but we would recommend replacing it. A new MAF sensor can be found for less than $30, check out this one on Amazon.

How long should it take for mass airflow sensor to re-calibrate?

Car does not run well, after installing cold air intake. Engine analyzer shows fault with mass airflow sensor. How long should it take to re-calibrate for extra air? My car has 111000 miles. My car has an automatic transmission. Hi, thanks for writing in.

What are the symptoms of a bad mass air flow sensor?

Some of the most common symptoms of a bad Mass Air Flow sensor in Mercedes Benz cars are: Engine dies, stalls soon after you start it. Engine hesitates when you accelerate. Poor throttle response. Engine hiccups. Engine displays unusually lean or rich idling.

How to know if your Mercedes C class is idle?

Check for vacuum leaks with a smoke generator injecting smoke into any vacuum line and see where the smoke comes out. That’s a leak that needs to be plugged. Other than that, there is the Idle Control Unit computer and the Idle Control Adjustment Valve, all which control the idle.

Why does my Mercedes Benz make a clicking noise?

It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.

Can you remove an alternator from a car?

Removing the alternator will require you to remove the drive or serpentine belt first and than the mounting bolts that attach it to the engine. Also dont forget to remove the negative cable to your battery as safety precaution.

Are there any problems with the Mercedes transmission?

Including Engine, Transmission, ABS, Airbag, SRS, SBC Brakes, ESP, EPS, Air Suspension and more. In depth troubleshooting, but only works on MB cars. 2. Launch Creader X431 VII works in European, Asian and Domestic Cars.

What should I do if my Mercedes FOB is not working?

If you need a replacement battery note that Mercedes-Benz uses CR2025 battery type. Ensure you have new batteries in your key fob. Next, look carefully at your Mercedes-Benz key. When you press the button on your key you should see a small RED led light.

What causes a Mercedes Benz key to not turn?

List of common problems and possible solutions 1 Locked Steering Wheel. New drivers always experience this at least once, so we thought we would include it in this list. 2 Discharged Battery Undervoltage. 3 Key Tumbler Defective. 4 Defective Electronic Ignition/Switch System EIS / N73. 5 Smart Key Remote. …

What are the problems with a Mercedes Benz?

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More

What should I do if my Mercedes Benz won’t start?

Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.

Why is the battery on my Mercedes Benz not working?

Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?

What are the symptoms of a bad accelerator pedal sensor?

In this article, you will find the most common symptoms of a bad accelerator pedal position sensor 1. Your car hesitates to move when the gas pedal is pressed 2. The engine doesn’t idle smoothly 3. Your car doesn’t accelerate over a specific limit 4. Your car won’t shift up or jerks upon depressing the pedal 5. You experience low gas mileage

Why does my car not respond when I press the gas pedal?

You may not be noticing a delayed response from the pedal, but if you see low gas mileage, it could mean that the car’s throttle position sensor is working but not as accurate as it should be. Modern cars have a monitoring system over all the sensors in the car engine.

What are the symptoms of a bad accelerator pedal?

Symptoms of a Bad or Failing Throttle/Accelerator Pedal Position Sensor. Common signs of a faulty pedal position sensor include inconsistent engine response, reduced fuel efficiency, and the Check Engine Light coming on. The days of having to constantly adjust the throttle cable due to a loose nut on the carburetor are long gone.

What happens when you press down on the gas pedal?

Engine response is inconsistent When you press down on the gas pedal, your engine should respond directly and instantly. However, when a problem with the APP sensor exists, the vehicle’s ability to consistently accelerate or decelerate as directed by the driver is reduced.

Why does my car not accelerate when I press the accelerator?

If the TPS malfunctions, the engine speed cannot be controlled by the accelerator pedal and engine speed will increase or decrease without any press or depress the pedal. Report this ad #4 – Dirty or Clogged Fuel Filters A dirty or clogged fuel filteris another reason for a car not accelerating like it’s supposed to when required to do so.

What happens when you change the O2 sensor?

The O2 sensor then sends information to the electronic control unit, or ECU, the vehicle’s computer. The ECU then adjusts the air-to-fuel ratio to optimize the fuel combustion. Sometimes an O2 sensor fails, and you need to replace it.

Why is my Mercedes-Benz transmission not shifting?

If cracks develop between the two chambers, coolant will mix with transmission oil and it will destroy the transmission. This has been a well-documented issue for Mercedes-Benz cars equipped with the Valeo radiators.

Is there a problem with the Mercedes possition sensor?

Mercedes-Benz throttle body or throttle position sensor found on C-Class, E-Class, S-Class, CLK-Class, SLK-Class may fail causing idle issues, no idle or poor acceleration. Symptoms of defective Mercedes throttle body or throttle position sensor include: A common problem that you may notice is that the car drives fine under normal acceleration.

There are never any notifications on the dash or any signs of it beginning to fail. This typically happens when I’m slowing down at an intersection or just driving slower in traffic.

What causes ABS warning light on Mercedes W204?

This fault can cause the engine to run rough and idle poorly. Common ABS pump and module failure for C-Class W204 range will cause the ABS warning light to illuminate and store fault codes for ‘internal fault’

What are the symptoms of a defective throttle possition sensor?

Symptoms of defective Mercedes throttle body or throttle position sensor include: A common problem that you may notice is that the car drives fine under normal acceleration. If you press the gas pedal to the floor or try to accelerate quickly or floor it, the engine stops responding, RPMs drop and it may even go into limp mode.

How to reset adaptive shifting points on Mercedes Benz?

This procedure will reset the adaptive shifting points in your Mercedes-Benz automatic Transmission Control Unit (TCU). These simple do it yourself instructions take less than 5 minutes. No tools are required to perform this procedure and make your Mercedes-Benz shift like new. Try this if your car has been shifting sluggish recently.

How long does it take to shift a Mercedes Benz?

These simple do it yourself instructions take less than 5 minutes. No tools are required to perform this procedure and make your Mercedes-Benz shift like new. Try this if your car has been shifting sluggish recently. This will make your car fun to drive again, it’s like getting a free tune-up.

Can you reset the transmission on a Mercedes Benz?

This will make your car fun to drive again, it’s like getting a free tune-up. This procedure applies to all Mercedes-Benz that come with the 5-speed 722.6 and 7 -speed 722.9. This is about 95% of Mercedes-Benz cars on the road today with the exception of models made before 1995. This reset procedure works on automatic transmission only.

How much does a 2004 Mercedes C Class C 240 cost?

Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2004 Mercedes-Benz C-Class C 240 Sedan 4D. View local inventory and get a quote from a dealer in your area.

Why are my wipers not working on my 2003 C240?

2003 C240. went to turn on the wipers today and nothing. I have done a little troubleshooting so far and have done some research on the forum. I have not found anything else not working.

How much does a 2004 Mercedes Benz cost?

Used 2003 Mercedes-Benz C 320 Coupe $4,995 HAG CORPORATION Used 2006 Mercedes-Benz C 350 4MATIC Sedan $5,900 Easy Motors Used 2005 Mercedes-Benz C 230 Sedan $5,990 American Motors Used 2003 Mercedes-Benz C 240 Sedan New Listing $4,700 BLOK Charity Auto Clearance

Can you jump start a Mercedes Benz with a dead battery?

Note: Jump starting a car with a fully discharged battery will shorten the life of the battery or damage the battery. Hint: For a safer method to jump start a Mercedes-Benz with a fully discharged battery see Method 3. Method 2 Jump start your car battery with a booster pack / jump starter box.

What kind of problem does a Mercedes C230 have?

21 people found this helpful. Folks I have a 1997 C230 Mercedes, This seems to be having the same problem, but when it Idles it runs rough and when driving it is stalling out but will re-start. I had the codes checked, came up with bad cam sensor.

Where is the jump start on a Mercedes Benz?

If your Mercedes-Benz doesn’t have the jump start connection points, you will need to connect directly to the battery. The battery is located in the trunk, engine bay, under the front passenger seat or under the rear passenger seat.

What to do if your Mercedes Benz wont start?

Get inside your Mercedes-Benz and start it. If it doesn’t start right away, let the battery charge for at least 5 minutes, or even longer if you can. If your Mercedes-Benz refuses to start, see the Troubleshooting FAQ section below. Once the car starts, disconnect the cables. Begin by disconnecting the negative battery cables on both cars.

What happens when a Mercedes Benz goes into limp mode?

When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level. The transmission has a dipstick tube but with no dipstick in it.

How to sync the remote control on a Mercedes?

1. Turn key to position 2 then back to position 0 and remove it. 2. With in 60 sec. push the lock button and lift gate button at the same time for 15 sec. 3. Press any remote control button twice to activate the system. 1. Turn key to pos.2 and back to pos. 0 and remove it. 2. with in 60 sec. press and hold the lock all button. 3.

Can you reset the ECU on a Mercedes C class?

Modern cars like the Mercedes-Benz C-Class “learn” your particular driving style over time and miles driven. For those who have acquired a used car and want it tailored to their own driving style, or those who just simply want to start over, resetting the ECU (engine control unit) is a good way to go.

How does auto close work on a Mercedes Benz?

Older Mercedes-Benz models before 1995 will most likely not have the auto close feature. They may have a micro switch on the window regulator that the window toggles on and off when it reaches the top or bottom position. When I park or turn off the car and try to close the windows, they do not go up all the way.

How do you sync the remote on a Mercedes?

Instructions on how to sync Mercedes remote: Insert the key into the ignition. Quickly remove key from ignition and within 10 seconds hold down the lock button. Continue holding the lock button, and at the same time press, the unlock button five times. Next release all buttons and press the gate/trunk button one time.

How can I tell if my Mercedes FOB is working?

Ensure you have new batteries in your key fob. Next, look carefully at your Mercedes-Benz key. When you press the button on your key you should see a small RED led light. The light should light up every time you press any of the buttons (Lock, Unlock, Panic, Trunk).

When does Mercedes Benz road side assistance start?

This is a free service for new car owners when activated within the first 90 first days of purchase. It connects the driver to Mercedes Benz road side assistance by using cellular technology and GPS to locate your vehicle.

Why does my car stall at a stop light?

While stopped at a stop light, my car will start to sputter as if it’s a bout to stall for a moment. Then, the car will rev up a bit and idle back up on its own. Also, after I stopped briefly to make a turn, when I pressed on the gas pedal it took about four seconds before the car would accelerate properly.

What causes a car to stall at idle?

There was a time when the stall happened that I received a message on the dash saying check alternator/battery, but I replaced the battery the day before and I know it can’t be the alternator because the car just wouldn’t start after.

How many miles can Mercedes last?

There is no simple answer as to how long or how many miles a Mercedes-Benz is good for. Some models have issues as early as 50k miles while other models can go over 200k miles with just regular maintenance.

What kind of mileage does a Mercedes Benz get?

They could easily go over 200k miles on original transmission and engine. The only issues you will see with these cars is a bad brake light switch (easy and cheap to fix yourself), ball joints, engine mounts and maybe an automatic transmission valve body repairs. E-Class is another Mercedes-Benz model that doesn’t mind the high mileage.

Are there any issues with a Mercedes Benz?

The only issues you will see with these cars is a bad brake light switch (easy and cheap to fix yourself), ball joints, engine mounts and maybe an automatic transmission valve body repairs. E-Class is another Mercedes-Benz model that doesn’t mind the high mileage. The W211 model was a complete redesign from the previous generation E-Class.

What causes a Mercedes C 180 engine to cut off?

[I have a similar experience, my 1996 Benz C 180 engine cut off when it has moved for like 30mins .l discovered that this happens when fuel pump is hot and it seems my fuel pump gets hot easily.l have changed my car fuel pump 2 times, yet the problem persists. A mechanic said it may be a dirty gas tank internal filter that reduce fuel supply

Why is my C200K AvantGuard engine cutting out?

2009 C200k Avantguard. With the crank position sensor fails it usually happens after the car has heated up. Let it cool and it starts up again. If this isn’t it, then it could be a faulty coil (s), or wiring harness (especially on pre-97 models).

Why does my car keep cutting off when I stop?

Why does my car keep cutting off when I stop? If your car shuts off after you stop it is because the engine is very sensitive at idle. This can be caused by many things but is usually caused by a lean fuel mixture, causing the idle to drop too low.

How to troubleshoot a Mercedes Benz convertible problem?

You can also bridge the top relay for a couple of seconds to see if the hydraulic pump start to run. Replace the convertible top relay if necessary, PN 0025421319. Next, check the micro switch where the divider locks. You know that trunk separator that you are supposed to pull out and engage it in this hook?

What are the most common problems with Mercedes Benz cars?

8 Most Common Mercedes-Benz Problems 1 Rust. Rust behind license plate / trunk area. 2 Engine Mounts. Engine mounts on Mercedes-Benz cars are oil filled. 3 Suspension & Steering Components. Ball joint / front control arm. 4 Window Regulators. Broken window regulator on Mercedes C-Class. 5 AirMatic Components. …

What does 3000 rpm mean on a CDI?

If i stand still and in N, the rpm wont exceed 3000 rpm either. BUT if I turn off the car, and start again it works perfectly fine again with lots of acceleration again, until I drive in the city again. No warning lights are on, and nothing really pops up with the diagnostic tool.

What are the common problems with Mercedes diesels?

Here are some common problems that affect many Mercedes-Benz diesel models including E350, ML350, GL350, R350, Sprinter, R320 CDI and BlueTec models. Common problems Diesel Particulate Filter. As Mercedes DPF traps and holds soot, with time it reaches a point when it needs to be ‘emptied out’. This is done by regeneration.

What causes a Mercedes C class to fail a state inspection?

If you take a Mercedes-Benz for state inspection, it is very likely to fail due to suspension issues especially if the car has over 100k miles. Broken window regulator on Mercedes C-Class. Window regulators do the hard work when you press the button to lower or close the windows.

What’s the problem with my Mercedes C class?

21 people found this helpful. its the same problem in my 2002 c200,it caused by the nuetral pooly and the engine fountdation……. 78 people found this helpful. Is that an easy fix?, 25 people found this helpful. you have to put arround 12-15 grands for the fix and have to order parts from company. 14 people found this helpful.

What makes a Mercedes C class run Ruff?

Dirty injectors ( irregular spray pattern, fuel comes out in a stream instead of a fine atomized spray) that will sure to make the car run ruff and run rich 4.

Navigation