How to reset the T Belt warning light?
T-BELT WARNING RESET COMPLETION a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch. b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
When to reset belt light on Kawasaki ATV?
However, the belt light may stay on after flipping the switch back to “ON”, or it may have come on automatically at 100 hours to get you to return the machine to the dealer for inspection even though the belt switch is not tripped. The following procedures will reset the light if the belt switch is not tripped.
How do you reset the belt on a landcruiser?
1. T-BELT MODE DISPLAY b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds. c) Release the trip switch, then press the switch again within 5 seconds. d) The digital display should change to T-belt mode. The initial display “15” (0,000km) is displayed (ie. 150,000km). 2. REWRITING REPLACEMENT VALUES
Why does my kvf360 reset belt light keep coming on?
Do not turn the ignition on with the CVT cover removed or the KEBC motor will spool out and prevent you from putting the cover back on (unplug the KEBC motor if you do). Note: A poorly connected battery can cause the light to repeatedly come on even if the switch doesn’t flip.
T-BELT WARNING RESET COMPLETION a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch. b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
1. T-BELT MODE DISPLAY b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds. c) Release the trip switch, then press the switch again within 5 seconds. d) The digital display should change to T-belt mode. The initial display “15” (0,000km) is displayed (ie. 150,000km). 2. REWRITING REPLACEMENT VALUES
How do you change to T Belt mode?
1. T-BELT MODE DISPLAY b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds. c) Release the trip switch, then press the switch again within 5 seconds. d) The digital display should change to T-belt mode.
What’s the best way to reset a check engine light?
In such a case, it is highly recommended to check the codes with a scanner instead. Switching the ignition on and off is also one method of hard reset without disconnecting batteries. Put the keys in your ignition and turn your ignition on and off consecutively after a second in each step.
How to reset PCM and check engine light?
First, park your truck and turn it off. Pull the hood lever under the driver’s side dash, and then pull the safety catch on the front of the hood to open it. Find the power distribution center (PDC); it will be a black box near the battery. Unlatch and open the cover of the PDC.
1. T-BELT MODE DISPLAY b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds. c) Release the trip switch, then press the switch again within 5 seconds. d) The digital display should change to T-belt mode.
What to do when your belt light keeps coming on?
Belt light came on and bike went to limp mode. Checked the toggle switch in the cover and did the belt light reset procedure. Belt toggle switch was not tripped as it was still in on position. Still reset the light and switched the toggle switch back and forth a few times just to be on the safe side.
Belt light came on and bike went to limp mode. Checked the toggle switch in the cover and did the belt light reset procedure. Belt toggle switch was not tripped as it was still in on position. Still reset the light and switched the toggle switch back and forth a few times just to be on the safe side.
How do you reset the belt light on a prairie 360?
Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them. Cut the key on to verify the procedure worked.
When does the V belt light come on?
Finally, the V-Belt light came on while riding home from work. I have wanted to do a video on this subject for some time, and here it is. The V-Belt light is keyed to come on every 16000 mile, which is the belt replacement interval. So if you changed your belt all ready don’t freak out.
How many miles does a T Belt reset take?
My ’98 KZJ95, with the 1KZ-TE motor – has 60,000 mile T-Belt interval. To reset the warning light I had to remove the dash and move a screw from one hole to another (each move shifts the counter on by 60,000 miles). No electronic resets on mine .
Is it possible to reset the warning lights on the dash?
This will result in a warning light appearing on your vehicle’s dashboard. After the repair is complete, however, it may still be necessary to reset your the computer in order for the warning light or lights to disappear. Fortunately, this process is fairly simple. Open the hood of your vehicle.
What do I do if my belt light is not turning off?
The switch you are trying to use to reset the Timing Belt counter is on the bottom left. Seen from the side it is clearly a ‘press to make’ electric switch. Here it is before being depressed: Total movement is about 2mm. So pressing the switch in (while the ignition is switched on) should reset the counter inside.
How can I reset the warning lights on my car?
Loosen the nut that holds the negative terminal to the battery with the pliers. The negative terminal is labeled with a minus sign (-) or is black in color; the positive terminal is red. Touching just the negative or positive terminal will not cause an electric shock, but touching both at the same time will.