How to replace ignition starter switch on VW Passat?
The video shows you how to replace the the ignition starter switch at a Volkswagen Passat 35i. For this repair the steering wheel, and the steering lock has to be removed. The late version of the 35i have a reduction sleeve on the steering column. Pulling the sleeve might be the most diffcult step of the repair.
Where is the ignition switch on a car?
These switches are located just to the side of the steering wheel and column on your dashboard, and are one of the main components in your car’s starter system. If the switch is not working, you will likely have to remove and replace it.
What to do if your ignition switch is not working?
If the switch is not working, you will likely have to remove and replace it. You can do this with a set of simple tools like a screwdriver. Turn on your power drill and use your drill bit to make a hold in the key slot of the ignition cylinder.
Where is the starter switch on my car?
These switches are located just to the side of the steering wheel and column on your dashboard, and are one of the main components in your car’s starter system. If the switch is not working, you will likely have to remove and replace it. You can do this with a set of simple tools like a screwdriver.
What should I do if I need to replace my ignition switch?
Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.
How do you remove a battery from an ignition switch?
Use an appropriate sized wrench to loosen the nut holding the cable on the negative (-) terminal and then slide it off the post. You don’t need to remove the positive cable from its terminal. Tuck the negative cable to the side of the battery to make sure it doesn’t accidentally come into contact with the terminals.
Where is the release pin on an ignition switch?
The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.
How do you replace an ignition switch on a car?
Installing a Replacement Squeeze the release pin on the ignition switch so it’s flush with the side. The same release pin that stopped the switch from coming out now needs to be pressed in so you can slide the switch into place inside the ignition module. Slide the ignition switch into its hole.
What to do if your key is stuck in the ignition switch?
The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.
What happens if you have a faulty ignition switch?
A faulty ignition switch in your vehicle can cause several problems ranging from your car stalling and all lights going dark to the radio not working unless the key is wiggled from side to side.
Is there a recall on a 1997 VW Passat?
Ignition switch failure while vehicle operational. Same condition was covered under recall on 1996 vw Passat models, manufacturer is not offering coverage on same body style under 1997 and 1995 designation. Impacted vehicle is a 1997 vw Passat wagon. The contact owns a 2006 Volkswagen Passat.
What kind of problem does a 1996 Volkswagen Passat have?
The contact owns a 1996 Volkswagen Passat. The contact started the ignition and the antilock brake system warning light illuminated on the instrument panel. While the light was illuminated, the air conditioner unit, windshield wipers, and headlights were inoperative.
Where can I get an ignition switch replaced?
The vehicle was taken to Volkswagen of new port richey (4719 us-19, new port richey, FL 34652) where it was diagnosed that the ignition switch needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure.
What causes a Volkswagen Passat to not start?
Your Volkswagen Passat ignition switch is the central player in your car’s ignition system. If the switch contacts get dirty or wears out, your car won’t start. Don’t let this happen to you — replace your ignition switch at the first sign of trouble with a part from AutoZone. Loading Price Use the form above to tell us what you drive.
Is there a problem with the steering column lock?
This is a VW Passat from 2005 with a faulty Steering Column Lock mechanism. Normally at VW you would need to replace the steering column lock and the comfort control module but we can do it with only replacing the lock and programming the module, saving a lot of money! This also affects the Passat CC and a few other VW models. Loading…
The starter is an electric motor that cranks the engine, effectively starting the car. It is under the hood, usually on the passenger side at the bottom of the motor next to the transmission. The ignition switch is a set of electrical contacts that activates the starter and usually is located on the steering column.
How can I tell if my ignition switch is working?
Test the Ignition Switch With the key in the RUN or ACC position, see if you are getting power to fuses 5, 8, 10, and 14. If you aren’t getting power there, check fuse 18 and see if it’s good. If it’s good, then check for power at pin 1 (red), 7 (red), 3 (pink/black) and 2 (gray/dark blue).
Can a bad ignition switch cause a bad starter?
The first thing to check in these situations is the battery. If the battery is OK, then you have either a bad starter or a bad ignition switch. With a little bit of time and some patience, you can tell which one is the problem. What Else Is Working?