How to re-connect power door lock and driver side power window?

Re-connect door window controller and locks wiring harness 5. Place the key in the ignition and turn to the run position 6. Connect Battery starting with the negative cable (ensuring not to connect then disconnect, (one swift motion)

Why is my power door lock not working?

Power door locks and driver side power window not working. Keyless remote will not open doors although when pressed, the interior lights come on so I don’t believe it is an issue with the fob battery. Other power windows work, just not the driver side. Remote mirror control on the door handle works.

How do you change the power door lock?

Do not remove the key from the ignition. Press and hold the power door lock button until the DIC display shows the current door lock mode. To view the next available mode, press and hold the reset stem until the mode appears. Release the reset stem and press and hold again to view the next mode.

How do you program a GM window switch?

GM Tech (Cam) : The programming of these modules is done with a scan tool and the GM programming software that connects the vehicle to the GM server and downloads the proper calibrations into the system. Customer: i need programing with my self

What kind of door lock and window switch does GM use?

An ACDelco GM Original Equipment Door Lock and Window Switch is a GM-recommended replacement for your vehicle’s original component. It enables you to lock and unlock your vehicle’s doors, as well as roll your vehicle’s windows up and down.

What is the left side power window switch?

Video Player is loading. This is a modal window. This switch replaces the left or driver side power window switch also known as the master power window switch,It controls all 4 power windows as well as the door locks, right and left side power windows, and window lock. Is my Power Window Switch or Power Window Motor the problem?

How to program a Chevy Tahoe power window switch?

The only possible way to not need to do this if you got a used switch from a vehicle that has the same options as your vehicle. If you can find someone with a Tech-2, they might be able to program it for you. You must log in or register to reply here.

Where is the fuse located on a GMC Sierra?

Auxiliary Power (Single Battery and Diesels Only)/ Dual Battery (TP2) Do not install fuse. The auxiliary electric cooling fan fuse block is located in the engine compartment on the driver’s side of the vehicle next to the underhood fuse block.

Where is the BCM located on a door lock?

The reason most guys try to find a “work around” is the high cost of a new switch module. The door lock and window circuits, on the driver’s side, share the same ground wire which terminates at the splice box on the left fender wall aft of the battery. Just for the record: The BCM doesn’t have anything to do with the operation of the windows.

What to do if your window lock does not work?

OOPS the control does not work, My solution, a damp sponge hold it to the contact for the window and lock terminals on the switch assemble, operate the switches, that has seemed to drain the static charge or electrical charge from the switch control. Leave no water behind before reconnecting the plugs.

How to fix a 2005 Chevy Colorado door lock?

Click to expand… I also have a 2005 Chevy Colorado with the exact same problem. I followed the advice given, that is removing the negative battery cable and holding it against the positive terminal on the battery for 30 seconds to completely discharge the BCM (body control module) and waiting 6 hours then reconnecting the battery cable.

Why does my window lock on my truck not work?

I had good luck on the drivers window/locks by resetting the BCM with the negative cable off for 10 minutes rather than waiting for it to reset itself, but others have found you can only wait. These are both common glitches, and not really indicative of the quality of the truck.

Where are the power locks on my car?

There is a single relay that controls both the power locks and the driver’s side window, located inside the driver’s side window switch. It can get stuck open, either from the BCM sending it into safe mode or, in my case, I think, because of extreme cold.

Where is fuse # 42 on power door lock?

If not, fuse #42 may be blown ( located in the underhood fuse box.) They say closing both windows at the same time or operating window and lock switches at the same time blows the fuse. You can’t post conmments that contain an email address.

What’s the problem with the Honda power window?

Most likely the problem is the switch. Honda/Acura use a polarity reversing ground at rest power window system, same as the door locks.

Why do I have to drive my car with the window down?

Its 15°F here and it would be nice to not have to drive with the window down. It’s either the wndow regulator motor or a frayed or broken wire, most likely in the wiring harness wher it flexes between the door and the body. If you plan to fix it yourself, you’ll need e meter, a diagram of how your door panel is installed, and a wiring schematic.

Why does my drivers side window not work?

A smaller version of GM’s rebirth of the Hummer. Hard to start yesterday,drivers side window,power door locks wont work,either by buttons on both doors or on key fob.Other windows work! Replaced Battery checked door lock fuse,still no drivers side window or door locks. Answered! View the answer I have this problem too Is this a good question?

Why does my driver side door lock not work?

The windows and the locks are on two separate circuits. The only part that these two have in common is the master switch. Of course it is also possible that the wiring harness between the driver side door and cowl is corroded and that some of the pins are to corroded or even broken off and do not make contact.

Why is the cowl not connecting to the driver side door?

Of course it is also possible that the wiring harness between the driver side door and cowl is corroded and that some of the pins are to corroded or even broken off and do not make contact. Also check that you have good and tight positive and negative battery cable connection to the battery posts.

Can a front passenger window and door lock work?

Yes the front passenger, rear drivers & Passenger windows/locks etc all work. Its only the drivers side. I purchased a used drivers side window/door locks switch as mine is all one unit and tryed that and did not work. Thank you for replying

Why are my door controls not working on my Chevy Duramax?

After a few weeks of intermittent minor power window problems (drivers side not wanting to work all the time but usable) all of a sudden none of of the driver’s door controls are working; power mirrors, power windows, door locks, heated seats, seat memory…nothing!

Why does the drivers side lock switch not work?

The drivers side window/lock switch does not work. Only on the drivers side that i can not get the locks to work, all 4 windows, or the outside mirriors, But if i go to the other doors and try to use the locks or window controls they work fine. I purcheased a new drivers side window/lock control and that did not solve the problem.

How to fix driver side power door lock?

1. disconnect the battery and connect both the positive and negative cables together(after disconnected)) 2. disconnect the window and lock controller in the driver’s side door. 3. Leave cables connected for at least 5 minutes 4. Re-connect door window controller and locks wiring harness 5.

What kind of parts are in an Oldsmobile mirror?

Note: mirror is NOS, but has four tiny unbroken blisters. Blisters are nearly inconspicuous, but they are there. Fits 1969-72 Delta 88 & 98 and 1971-72 Toronado as a glove box lamp switch assembly. Fits 1971-72 F-85 & Cutlass with automatic transmission and center console as a console compartment lamp switch assembly.

How to connect battery to power door lock?

Connect Battery starting with the negative cable (ensuring not to connect then disconnect, (one swift motion) 8. You should hear a series of dings 9 Once dings are heard remove the key from the ignition and you should hear the door lock solenoids activate..

How to re-connect driver side power window controller?

3. Leave cables connected for at least 5 minutes 4. Re-connect door window controller and locks wiring harness 5. Place the key in the ignition and turn to the run position 6. Connect Battery starting with the negative cable (ensuring not to connect then disconnect, (one swift motion)

Why is my driver’s side window not working?

The driver’s side window motor may have gone out, or there should be a short or bad connection in the switch. You could try taking the door card off and inspecting the window switch connector. I’ve had luck in the past just unplugging and plugging it back in when my passenger window was working intermittently.

What are the symptoms of a bad power window switch?

If you suspect your power window switch is going bad or failing, watch for the following symptoms: 1. All the windows quit working If all of the windows quit working at once, meaning there is no response when you push the power window switch, chances are there is a loss of power in the electrical system.

Is there a fuse for the drivers side window?

Three windows now work but drivers side window has no voltage to window motor plug. have the same problem? That circuit does not use a fuse. It is powered by a circuit breaker labeled “ACCSRY PWR”, on the yellow wire.

What happens when a power window switch fails?

Window works from master switch only In some cases the window may not work from its own switch, but the master switch can still put the window up or down. In this case there is a good chance that the power window switch has failed and that the other window components are working properly. 4. Windows work sometimes

Can a passenger side window be controlled from the driver side?

After the jump start the passenger window stopped working. It works fine from the passenger side switch. Any ideas? I’d rather avoid a trip to the dealer if possible. Thanks. My passenger side front window can no longer be controlled from the driver’s side.

Why does my power window go down but not up?

When you operate the up cycle, the switch reverses the polarity on those same two wires. So if the motor works in one direction just fine, but not in the other direction it’s almost NEVER the motor—it’s the switch. Aside from not working at all, a power window that goes down but not up is the second most common complaint.

Why is my driver’s door electric window not working?

If only the driver’s door electric window fails to operate or operates intermittently, the most likely cause is a fault in the Electric Window Module (ECM). The fault is most likely a bad joint in the printed circuit board (PCB) of the ECM.

How does a power window work in a car?

Every power window requires a window motor to supply the electrical energy. There is a gear at the end of the power window motor which connects with the window regulator. When you press the up or down button on your door, it activates the window motor which then allows the window regulator to move the window.

What to do if power window does not work?

Put power and ground directly to the connections to check that this power window motor works. Check the movement in both directions by flicking the switch to reverse the polarity. If the motor does not work, or works in one direction only, the motor needs to be replaced. Replacement power window motors are available without the regulator.

Why is my power window fuse not working?

If the fuse is good pull out the driver side master window switch and check if the purple wire has power which supplies power to both switches. There could be a break where it goes into the door before it reaches the window switch. The fuse and purple wire are the power sources, not the solder joint.

Navigation