How to program Hyundai Elantra keyless entry remote?
Press the LOCK button on the first remote to be programmed. If programming a second remote press the LOCK button on the second remote. Slide the switch on the alarm system control module to the OFF position. Turn the ignition OFF and remove key. Replace center fascia. Programming is now complete, test remotes to ensure proper programming.
What are the different types of Hyundai Elantra keys?
Hyundai Elantra was introduced in 1992. This model has five versions and thirteen types of keys. Remote Key Fob: 2011-2019 – Three types of remotes. Transponder Chip Key: 2007-2012 – Two types of keys. Non-transponder Key: 1992-2019 – Eight types of keys.
Do you need to program a Hyundai key fob?
Hyundai transponder and remote car keys, also known as key fobs, smart keys or push to start keys, are the latest generation of security car keys. Therefore, onboard programming or self-programming is not available for these type of keys or remotes and an additional equipment or programming machine is necessary to complete this process.
Do you have to program the remote to start the car?
Therefore, the key or remote will have to be programmed to start the car. By saying “programmed” it means the car’s computer must be able to recognize the key as “authorized key”. Authorized keys may be added by programming those keys with a special programming machine that the dealer has or most automotive locksmiths.
When did the Hyundai Elantra remote key come out?
Hyundai Elantra was introduced in 1992. This model has six versions (Hyundai Elantra w/Prox, Hyundai Elantra w/0 Prox, Hyundai Elantra Touring, Hyundai Elantra (Canada), Hyundai Elantra Touring (Canada), Hyundai Elantra GT) and eighteen types of keys. Remote Key Fobs: 2011 to 2021.
How do I get my Hyundai Elantra to turn on?
REMOVE dashboard fascia and LOCATE the alarm system control module. ENSURE that the memory switch is in the OFF position. INSERT key into the ignition and TURN ignition to the ON position. NOTE: Some have reported that leaving the key out of the ignition works for their vehicle. If this procedure does not work for you, try skipping this step.
Can You program a remote key fob for your car?
Program a remote key fob for your car, simple and easy steps – YouTube Programming a key fob is easy just follow the steps and you should be all set, no need to go to the dealership and have them charge you at least 200$ for a s…
Where is the ETACS unit on a Hyundai Elantra?
To reprogram the key less remoteThe ETACS unit, which controls the alarm, is bolted to the dash chassis and is located immediately behind the climate control cluster, offset a little to the left. You need to gain access to this unit to code a new remote.
Insert key into the ignition and turn ignition to the ON position. After 5 seconds slide the switch on the alarm system control module to the SET position. Press the LOCK button on the first remote to be programmed. If programming a second remote press the LOCK button on the second remote.
Where is the module on the Hyundai Elantra?
The module is indeed under the dash, in center, on pass side slightly, just above the floor. I have done this. There is NOT a 1 & 2, there is a operate and teach (essentially) setting. Flip the switch to teach, with the key on. push both remote buttons within a short time, then return switch to operate.
How to program the Hyundai Santa Fe remote fob?
1 Enter Programming Mode – Step 1 REMOVE dashboard fascia and LOCATE the alarm system control module. 2 Enter Programming Mode – Step 2 INSERT key into the ignition and TURN ignition to the ON position. 3 Enter Programming Mode – Step 3 After 5 seconds SLIDE the switch on the alarm system control module to the SET position.
Are there any programs for the Hyundai Elantra?
It says they are applicable for all 2001-2004 Elantra models. Programming is free if you do it yourself. 2. behind the ashtray is the ETACS module, it’s the computer that controls the alarm, turn signals, basically everything that doesn’t make the car move. 3. there’s very small DIP switches somewhere on the module, with a 1 and 2.