How to identify the forks on a Harley Davidson?
Identifying which exact fork (front end) is on your Harley-Davidson motorcycle can be problematic. Especially with older bikes, many parts of motorcycle forks can be changed to different styles, or replaced with aftermarket parts. In this article we share photos and identifying characteristics for a variety of front ends found on Harleys.
How do you replace a front fork on a Harley Davidson?
Loosen the two nuts at the bottom of the right side fork slider. Support the front wheel and pull the axle out from the right side. Do not lose the spacers between the wheel and fork sliders, or the ABS sensor if equipped.
How do you remove oil from Harley Fork?
This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. Bob and Mark demonstrate the best way to empty Harley fork oil from your Sportster’s front fork sliders and replace it with new oil.
When did Harley Davidson stop using Duo Glide Forks?
This article applies to the Harley Touring Models (2000-2013). Harley Touring bikes have used the same basic front forks since the 1980’s, all of them based upon the first Duo-Glide forks in the 1960’s. It’s a simple thing to remove for service, or for an upgrade.
How do you change fork oil on a Harley?
This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. Bob and Mark demonstrate the best way to empty fork oil from your Sportster’s front fork sliders and replace it with new oil. It can be a two-man job, so try to complete the service with a friend.
How big of a fork do you need for a Harley?
It can be a two-man job, so try to complete the service with a friend. Newer bikes mostly use 39-millimeter forks, but most bikes are preset with varying levels of spring in the sliders, so consult your manual before you begin this service.
How big is the spacer on a Harley Davidson Fork?
One spacer is still used for the left side. So, I decided to eliminate the right side Harley wheel spacer and incorporate the length of the spacer into the 32mm portion of the new axle. I will replace the oil seal on that side of the wheel with a 45x32x6mm seal so the axle fits against the hub.
Can a two man service change fork oil?
Bob and Mark demonstrate the best way to empty fork oil from your Sportster’s front fork sliders and replace it with new oil. It can be a two-man job, so try to complete the service with a friend.
What’s the best way to replace a fork?
Remove the brake calipers, fender, front wheel and any other hanging cables. Disassemble the fork. Loosen the bolts further and pull downward on the fork while twisting. Remove the fork cap carefully. Because it is spring loaded, be careful not to stand in the way of the cap as you remove it.
What does the fork do in a car?
The fork plays a critical role in steering, suspension, and braking. The fork itself consists of 2 “legs,” or tubes, each of which is fitted with a special seal that keeps the lubricating oil in the interior from escaping.
Where is the seal on a steel fork?
Pry off the ring-shaped rubber dust seal and semicircular metal C-clip at the center of the fork leg with the tip of a screwdriver. Then, give the 2 halves of the fork a sharp tug to separate them. Removing the slider piece will expose the fork seal, which sits near the bottom of the stanchion.
What kind of fork tubes does Franks Forks make?
Franks Forks (AKA: Forking by Frank) builds fork tubes for virtually all models of Honda Motorcycles from the early 1970’s through current models. Whether you are looking for front end parts for a CB, CR, Shadow, Nighthawk, Twinstar or a scrambler, Franks can build them for you.
Remove the brake calipers, fender, front wheel and any other hanging cables. Disassemble the fork. Loosen the bolts further and pull downward on the fork while twisting. Remove the fork cap carefully. Because it is spring loaded, be careful not to stand in the way of the cap as you remove it.
The fork plays a critical role in steering, suspension, and braking. The fork itself consists of 2 “legs,” or tubes, each of which is fitted with a special seal that keeps the lubricating oil in the interior from escaping.
How do you put a seal on a fork?
Rub oil on the inner part of the new seal. Put the seal over the stanchion and slide it down into place. Set the seal with a seal driver. This will tap the seal into place gently but firmly. Put the fork back together. Situate the clip and dust seal back onto the fork. Place the damping rod back inside.
Identifying which exact fork (front end) is on your Harley-Davidson motorcycle can be problematic. Especially with older bikes, many parts of motorcycle forks can be changed to different styles, or replaced with aftermarket parts. In this article we share photos and identifying characteristics for a variety of front ends found on Harleys.
How to alignment the front fork on a motorcycle?
4 Spin the wheel as vigorously as you can and abruptly clamp on the brake. Holding the brake lever on, tighten the front axle **5 **Lower the bike onto the ground, and, while holding the front brake, gently pump the forks a few times.
How do you close the modal on a Harley Davidson?
This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. Sign up for premium membership and get access to our best Harley repair videos and step-by-step instructional projects.
When to remove the wheel from a front fork?
Anytime the wheel is removed, perform steps #4 and #5: that’ll center the wheel in the fork and provide better suspension and braking action.