How to check the fault code on a Harley Davidson?
Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module.
How do I get the DTC code on my Harley?
To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer reset button again to view additional codes if they exist. 1 – Record the codes.
Where is the Diag switch on a Harley Davidson?
The trip odometer trigger switch is located in the left hand control module. The switch signal is sent to the speedometer over the CAN bus. If there is a problem with the CAN bus, the odometer self-diagnostic mode may not function. 1. Release the trip odometer trigger switch. “diag” will appear on odometer display.
How to get the ECM code on a Harley Davidson?
The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley guage cluster as well as a list of codes. 1- Turn Ignition switchto OFF & Run/Stop switch is to Run. 2- Push odometer resetbutton in & hold. 3- Turnignition switchto Ignition and release the odometer reset button.
How to get the trouble codes on a Harley Davidson?
The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.
How to troubleshoot an ICM error code on a Harley?
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release the odometer reset button.
How to reset odometer on 2014 Harley Davidson Moto?
1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold. For 2014 & newer touring models this will be the toggle switch on the left control mount. 3- Turn ignition switch to Ignition and release the odometer reset button.
The trip odometer trigger switch is located in the left hand control module. The switch signal is sent to the speedometer over the CAN bus. If there is a problem with the CAN bus, the odometer self-diagnostic mode may not function. 1. Release the trip odometer trigger switch. “diag” will appear on odometer display.
What is the EFI code for a Harley Davidson?
P2138 TGS Correlation Error (Twist grip sensor) 27. P0120 TPS1 Range Error 28. P0220 TPS2 Range Error 29. P0122 TPS1 Low 30. P0123 TPS2 High/Open 31. P0222 TPS2 Low 32. P0223 TPS2 High/Open 33. P2135 TPS Correlation Error 34.
How to get the DTC code on a Harley Davidson?
6 – To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s.
When did the Harley Davidson flhtcui Electra Glide come out?
Jun 26, 2017 | 2000 Harley Davidson FLHTCUI Electra Glide… May 30, 2017 | 2000 Harley Davidson FLHTCUI Electra Glide… May 26, 2017 | 2000 Harley Davidson FLHTCUI Electra Glide… 2000 Harley Davidson FLHTCUI…
Why do I get p1353 on my Harley Davidson?
Thanks Those codes could be caused by the PC or a number of other things also like plugs, plug gap, plug wires, loose plug tip where the wire joins on and even bad wiring on the injectors near the plug.
What does 1353 mean on a Harley Davidson?
Today, the 1353 code ” Front cylinder no Combustion EFI” started. I had a power comander on it until 2 days ago when I disconnected it. It didn’t seem to help the heat problem I installed it for and it really used the gas. The bike seems to run fine. I wonder if this is a problem with the EFI?
What is the Harley Davidson no combustion EFI code?
Discussion in ‘ Electrical ‘ started by jaceddie, Aug 15, 2008 . I have a 2004 Ultra that had the 1356 code “Rear cylinder no Combustion EFI” come up last week. Today, the 1353 code ” Front cylinder no Combustion EFI” started.
What does diag mean on a Harley Davidson?
3- Turn ignition switch to Ignition and release odometer reset button. Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.
6 – To get the DTC within an area of diagnostics, push and hold the odometer resetbutton in for 5 seconds and release. If there are any DTC’s the code will be displayed or the word “none” will appear if there are no DTC’s. Push the odometer resetbutton again to view additional codes if they exist. 7 – Record the codes.
How to check your Harley Davidson for problems?
Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate.
What to do if your bike has an error code?
Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module. 10 – Turn Ignition switch to OFF.