How to check Mercedes Benz SLK 230 reading fault codes?

Before plugging the scan tool into the car’s diagnostic port, make sure that the car’s battery has at least 11.4 volts with the key off and that the battery cables are clean and secured to the terminals. Plug the scan tool into the data port and turn the ignition on. For other details, refer to the scan tool’s owner’s manual.

Is there a problem with the throttle sensor on a Mercedes?

Mercedes-Benz throttle body or throttle position sensor found on C-Class, E-Class, S-Class, CLK-Class, SLK-Class may fail causing idle issues, no idle or poor acceleration. Symptoms of defective Mercedes throttle body or throttle position sensor include:

Where is the USB port on the R170 SLK?

On the R170 SLK, the port is located on the under-dash panel, behind the hood-release lever (blue arrow). The port is protected by a plastic cover, which pivots away so that the cable can be plugged in.

How can I find out my Mercedes Benz fault code?

Scan tools run the gamut from affordable ones that only reveal the fault codes up to the multi-thousand-dollar Star Diagnostic System used by Mercedes-Benz dealerships and some independent repair shops. The consumer end of the scale also includes Bluetooth versions that transmit the data to smart phones.

What should I do about my Mercedes slk230 low idle problem?

Solutions will vary from vehicle to vehicle. This just happens to be a Mercedes SLK230 and the problem was the gas pedal position sensor, but other vehicles or even this vehicle may have the same symptoms but have a different solution. 1. Ignition coils 2. Coil wires and connectors 3. Egr vacuum switching solenoid valve 4.

Why does my Mercedes have a low idle?

This video shows several different solutions to the low and/or rough idle that many vehicles have. Solutions will vary from vehicle to vehicle. This just happens to be a Mercedes SLK230 and the problem was the gas pedal position sensor, but other vehicles or even this vehicle may have the same symptoms but have a different solution. 1.

How to reset service light indicator Mercedes SLK 200 Kompressor?

Manual Reset Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds. Present status for days or distance is now displayed. Within 10 seconds, turn key in steering wheel lock to position 0. Press and hold button to the left of speedometer, while turning key in steering lock to position 2 again.

What’s the difference between a 1999 C230 Kompressor and a 1999 SLK?

And in the 1999 C230 Kompressor, Kompressor being German for supercharger, the difference is immediately apparent. But first, the numbers. Borrowed from the SLK roadster, the 2.3-liter supercharged, intercooled 4-banger makes the same 185 horsepower and 200 pound-feet of torque.

Is the Mercedes SLK 230 a good car?

I purchased a 1999 SLK 230 off an auction on Ebay a couple of years ago. It was a fantastic car and I put over 35,000 miles on it with virtually no issues beyond replacing tires and a couple of belts. Until I hit a section of black ice this winter on I-80 and collided with a guardrail. Damages exceed car value and I could not work out fixing it.

When was the R170 version of the SLK made?

The R170 version of the SLK was only made from 1998 through 2004, averaging about 10,000 US versions each year. I’ve discovered that only about 10 percent of these have manual transmissions. What are you thinking when you order a 2 seater sports car with an automatic transmission? I find that mystifying.

How do you change MAF sensor on 2001 SLK 320?

IHAVE A 2001 SLK 320 THAT LEAKS HYDROLIC FLUID AT THE BOTTOM OF A PLUG ON THE LEFT SIDE WHEN THE PUMP IS ON THE RIGHT THERES A TUBE ON THE BOTTOM THAT FLUID POURS OUT TOOK EVERU THING OUT OF TRUNK AND… read more Marty Mercedes Technician Associate Degree

What’s the fault code for a 2001 Mercedes Benz?

Click to expand… For the ML class it does not apply to the 2001 models. Also the fault code in the bulletin is for DTC B9103 and DTC B9123. No others would be covered by the DTB. Post # 34 in this thread lists the DTB the parts, and all affected models.

Why does my Mercedes say dont start motor?

– within 30sec place the key in the igntion and turn the key to pos 2 (dont start motor). So now the dealership is saying that the tranny leak at sensor (which I have ignored for years) has leaked fluid along the wires and ended up getting fluid in some control module.

What causes a Mercedes Benz steering angle sensor to lose memory?

B1628 Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. Body C1140 BAS light, play in steering column causes steering angle sensor to lose memory (?) Chassis C1504 BAS light, play in steering column causes steering angle sensor to lose memory (?) Chassis P0818 Driveline Disconn. Switch Input Circuit Malfunction

Is the 2003 Mercedes Benz SL Class A good car?

Edmunds’ expert review of the Used 2003 Mercedes-Benz SL-Class provides the latest look at trim-level features and specs, performance, safety, and comfort. At Edmunds we drive every car we review, performing road tests and competitor comparisons to help you find your perfect car. Read the full in-depth review of the Used 2003 SL-Class at Edmunds.

Is the Mercedes-Benz SLK 350 a good car?

It may be the most pragmatic roadster of its kind, but the SLK 350 dares you to doubt its partying skills. The 2012 Mercedes-Benz SLK still may be the least honed, least intense of the trio of pricey German roadsters, but it’s ripened over its 15 years and three generations.

What kind of engine does a SLK have?

Thus far in the 2012 model year, we’ve driven two flavors of SLK–the eventual mid-range SLK 350 and the sizzling V-8-powered SLK 55 AMG. There’s a turbo four-cylinder SLK in the pipeline, too, but it’s likely tagged for a 2013 model-year intro.

What kind of car is a 2003 Mercedes SLK?

Used 2003 Mercedes-Benz SLK-Class SLK 230 Roadster 2D Edit OptionsMileage: 108,005 4.6 Consumer Write a review View Gallery For Sale Near You 22 Mercedes-Benz SLK-Class vehicles in your area. Used 2004 Mercedes-Benz SLK 320 $8,291 Reduced Nexxt Car Inc Used 2005 Mercedes-Benz SLK 350 $12,999 Rose Motorcars Used 2002 Mercedes-Benz SLK 320 $9,900

When was the Mercedes SLK 230 last serviced?

No accident or damage reported to CARFAX… 1st owner purchased on 02/08/02 and owne… Last serviced in Cottage Grove, OR on 05… 1st owner drove an estimated 4,317 miles… No accident or damage reported to CARFAX…

How much does a Mercedes Benz SLK 350 cost?

Mercedes-Benz SLK 350 $14,990 Stellar Auto Used 2005 Mercedes-Benz SLK 350 New Listing $15,500 Shift Los Angeles Used 2003 Mercedes-Benz SLK 320 New Listing $16,777 U Car Connect Used 2004 Mercedes-Benz SLK 320 New Listing $18,777 U Car Connect Used 2005 Mercedes-Benz SLK 350 $19,950 Reduced Motor Cars LA LLC Used 2002

What kind of tires does a Mercedes SLK32 have?

Double-spoke, 17-inch alloy wheels on the SLK32 AMG hold P225/45ZR17 tires up front and P245/40ZR17 tires in the rear. A front air dam incorporates AMG fog lights, while a small lip spoiler at the rear of the trunk lid reduces aerodynamic lift by more than 50 percent, according to the manufacturer.

How many hydraulic cylinders are in a SLK 230?

Five hydraulic cylinders, nine limit switches, a control switch, four window motors, a pump, two solenoids, a relay, cables/pulleys, and a control module all have to work in sync for the top to operate properly. If one link in the chain breaks down, the top either won’t work or it stops mid-retraction.

Where is the fill hole on a Mercedes SLK 230?

If the fluid is low, the fill hole is on top of the hydraulic pump. The plug is easier to access by removing the metal cover, which is secured by four bolts having T30 Torx heads (arrows). The filler hole (arrow) is on top of the pump, on the right-rear fender side.

What should I do about my Mercedes SLK top?

If one link in the chain breaks down, the top either won’t work or it stops mid-retraction. For the average SLK owner, top troubleshooting is possibly better left to the pros. The Vario Roof Diagnostic Aid manual is detailed and extensive.

How much is a 2001 Mercedes Benz SLK Class worth?

Compare to Similar Vehicles Used 2001 Mercedes-Benz SLK-Class Used 2012 FIAT 500 See Details Price $6,374 $6,447 KBB.com Rating N/A 3.6 Consumer Rating 4.6 4.4

When did the Mercedes Benz SLK face lift?

As reported in Automotive News, Mercedes-Benz sold 12,930 SLK models during 2000. Face lifting for 2001 includes new front and rear aprons, body-color door handles, sculpted rocker panels and revised two-color taillights.

What kind of engine does a Mercedes SLK have?

Months before the 2001 model year actually began, a V-6 engine became available in Mercedes-Benzs rear-drive two-seat roadster, which is fitted with a retractable steel hardtop. Several styling changes also can be seen on the SLK series, which remains available with a supercharged four-cylinder engine that gains 5 horsepower this year.

How much does a 2001 Mercedes Benz cost?

Monthly Estimate based on a 4.4% rate for 60 months, $7,973 vehicle price, $0 down payment, $0 trade-in, $0 sales tax. The dealer was very committed to ensuring that we were satisfied with the mechanical, cosmetic and financial concerns about the vehicle.

Why does my SRS light keep going on?

Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Step 1 Install a new battery; Step 2 Reset SRS/ Airbag light. Instruction on How to Reset the SRS Light on a Mercedes Benz: 1.

What does the SRS light mean on a Mercedes Benz?

What does SRS light mean? SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system.

Where is the SRS light on the dash?

If the red SRS lamp on the dash is accompanied by the orange airbag lamp next to the transmission shifter is lit, the fault is commonly connected to the passenger seat sensor.

What does it mean when SRS warning light stays on?

SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system. It is very unlikely that your airbags are going to deploy randomly, but the concern is that they may not deploy…

Is there a way to reset the SRS light?

You can’t rest the airbag SRS light with a simple OBD II scanner which gives you the check engine light codes. You will need a more advanced scan tool to reset the airbag light. For around $110-150, which is how much a diagnosis costs anyway, you can get your airbag reset tool.

When did the Mercedes SLK 230 come out?

The SLK is a compact luxury roadster manufactured by Mercedes-Benz in three generations; R170 launched in 1996, the R171 in 2004 and R172 in 2011. Mercedes SLK 230 is a two-door cabriolet produced in several generations since 1996. It was manufactured with petrol engines and was available with both, automatic and manual transmission style.

What’s the top speed of a Mercedes SLK?

This model has top speed listed as 240 km/h and can accelerate from 0 to 100 km/h in 7.2 seconds. American entrepreneur Jim Rogers and his wife, Paige Parker, drove a highly modified SLK through 116 countries between January 1, 1999 and January 5, 2002, covering 245,000 kilometers and setting a Guinness World Record.

What are the readiness monitors for Mercedes Benz?

Many drivers have had difficulty completing readiness monitors for their Mercedes Benz. The two readiness monitors that seem to be the most stubborn to complete are: Secondary Air Injection and Catalyst (Catalytic Converter). We located a Mercedes Benz Service Bulletin (S-B-14.00/17) that may be helpful.

What kind of diagnostic scanner does a Mercedes Benz use?

It will scan and erase codes for the Airbag, Powertrain, Chassis, Body, Engine, Transmission and Information & Communication systems. The Carsoft 7.4 Multiplexer is designed specifically for Mercedes-Benz cars. While it can read and reset all the systems in most Mercedes-Benz models it has limited programming functionality.

Why is the SRS light on on my 1992 500SL?

The SRS light is on when the car (1992 500SL) is driven. The dealer has checked the diagnostics and says it is because of a drivers seatbelt buckle failure and this needs to be replaced – surprise surprise – for $380. Can I use one from a different model car?

How do you reset the SRS light on a car?

The SRS light has to be reset via a STAR unit or at the dealer. There are no pins to reset it in the on board connector in the engine bay. With my issue, I reset the light but the buckle would not operate properly until I replaced it. I couldn’t really justify having a passenger with a faulty seatbelt in the car.

How to read and reset SRS / airbag light?

Battery dying. How to read and reset SRS/ Airbag light? Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it.

Is there a scanner that reads the SRS light?

Here is a scanner that works with Mercedes-Benz and will rear fault codes and reset the AirBag, ABS and check engine light. Our favorite scanner that for an in-depth Mercedes-Benz troubleshooting is the iCarsoft MB II. Not only does it read the SRS light (Airbag Control Unit) but also every control unit in your Mercedes-Benz.

Is the CAN bus on a Mercedes slk230?

On my slk230 from 1998 I get the same code. (with the Mercedes DAS multiplexer). Cannot get it erased. ABS/ASR and the BAS lights stays on. I have read a lot of topics, but I am having trouble to determine what the CAN Bus exactly is.

What does code c1025 mean on Mercedes Benz?

code C1025 is defined as ” CAN Communication BAS communication with ESP control unit faulty.” This basically means that the BAS module is not networking correctly with the ESP module, commonly this is usually a glitch code, unless it returns more than once.

Why does the Bas light come on on my Mercedes SLK?

The speed sensors are behind the rotors, held on with Allen screws. Spraying these with electrical contact cleaner can solve the problem. The charging system can also be the root of the problem. The BAS/ASR light will come on if the system falls to 10 volts or less.

Where to find DTC code on Mercedes SLK 230?

The dreaded Check Engine light (arrow) stays illuminated when the car’s computer registers a diagnostic trouble code (DTC). Disconnecting the battery doesn’t erase the code. The scan tool’s cable (or a Bluetooth module on wireless systems) plugs into the OBD-II diagnostic port (yellow arrow).

Where is the fault code on a Mercedes SLK?

Disconnecting the battery doesn’t erase the code. The scan tool’s cable (or a Bluetooth module on wireless systems) plugs into the OBD-II diagnostic port (yellow arrow). On the R170 SLK, the port is located on the under-dash panel, behind the hood-release lever (blue arrow).

Why is the Bas light on on my Mercedes slk230?

In a case where the code returns immediatly, the BAS or ESP module is faulty. This system requires a Mercedes level scan tool to test. Click to expand… On my slk230 from 1998 I get the same code. (with the Mercedes DAS multiplexer). Cannot get it erased. ABS/ASR and the BAS lights stays on.

What to do if the OBD II scanner doesn’t communicate with the vehicle?

What to do if the OBD II scanner doesn’t communicate with the vehicle. TEST 1: Connect the positive DMM lead to DLC pin 4 and the negative DMM lead to the negative battery terminal, using jumper wires if necessary. Do not connect to the body or chassis ground but to the battery terminal directly.

When did Mercedes Benz start using OBD-II?

Beginning in 1996, passenger vehicles adopted the OBD-II closed-loop engine management system, which uses oxygen sensors before and after the catalytic converter to monitor emissions and adjust fuel management accordingly.

Why is my OBD2 not connecting to YouTube?

These issues include an incompatible obd2 scan tool, bad fuses, damage in the circuit board, ECU, and failed computer. OBD-II…. Non connecting data Port Issue. *FIXED* This might help you! – YouTube OBD-II…. Non connecting data Port Issue. *FIXED* This might help you! If playback doesn’t begin shortly, try restarting your device.

Where is the OBD connector on a Mercedes SLK?

OBD connector location for Mercedes SLK Class – R170 (1996 – 2004) You will find below several pictures which will help you find your OBD connector in your car. The OBD connector is located inside of the vehicle, above the pedals.

Is there a problem with my SLK 230 R170?

Hi I have recently had a ‘No Start No Crank’ problem with my SLK 230 R170. This happens when the key is turned on and all the dashboard lights show but the engine will not turn over. I did some research on this problem and it appears that this is a common fault with this model and there is a simple fix which can be found on You Tube

What to do when your Mercedes goes into limp mode?

You may also get a check engine light if your transmission goes into limp mode. When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level.

What to do when your transmission is stuck in limp mode?

The majority of the time, the problem is not as grave as you may think. If your transmission is stuck in gear and you are far away from home, try this: Pull over and turn the car off. Remove the key. Do not press the gas pedal or any other buttons on the car. Wait 20 seconds. Start the car and drive to see if it is out of limp mode.

What does it mean when your car is in limp mode?

Known as the limp / fail safe / emergency mode is when your transmission is stuck in one gear and doesn’t shift. In this condition, you only get speeds up to 30 mph max. Why does this happen? When the sensor input values from the different sensors inside the transmission]

How do you lock the ignition switch on a Mercedes SLK?

Alternately, it can be pried off carefully using a small flatblade screwdriver. For reassembly, the ring’s clips (arrow) grab the slot in the dash panel directly under the key cylinder. The special Lock Cover Tool catches the key’s remote fob, causing the key to move with the tool.

Can you change the cylinder on a Mercedes SLK 230?

A better method is with a purpose-specific Lock Cover Tool (Pelican Parts #BM-202-0014). Once the cover is released, the key and tumbler can be pulled out of the steering lock. The one drawback to ordering a new cylinder and key is that the trunk lock will still require the original key.

Where is the fluid reservoir in a Mercedes Benz?

In most Mercedes-Benz cars including SL, SLK, CLK class, it is located in the trunk left or right side. You will need to remove the trunk lining to see the reservoir. Remove the 12mm bolt from the reservoir. Use a clean syringe to add fluid to the reservoir. Hopefully, by now you have pinpointed the problem.

How to reset service light indicator Mercedes SLK 200?

Manual Reset Turn key in steering lock to position 2. Within 4 seconds press button (1) left of speedometer twice. Picture below. . The present status for days or distance displays, within 10 seconds turn key in steering lock to position O. Press and hold button (1), while turning key in steering lock to position 2 again.

When does an ECU fault code come on?

Quality airbag module reset services! When a car’s Engine Control Unit (ECU) senses a problem or malfunctioning within the vehicle, it triggers an ECU fault code that will turn on the check engine light. If your check engine light comes on, the ECU fault code can tell you exactly what problem your vehicle is experiencing.

How can you tell what’s wrong with your ECU?

ECU Fault Codes: How to Tell What’s Wrong with Your ECU. When a car’s Engine Control Unit (ECU) senses a problem or malfunctioning within the vehicle, it triggers an ECU fault code that will turn on the check engine light. If your check engine light comes on, the ECU fault code can tell you exactly what problem your vehicle is experiencing.

How to reset check engine light on Mercedes slk230?

I found on the wiki a method how to reset check engine light on your MErcedes SLK230, switch the key in ignition on position 2, turn steering wheel full left then full right and back to centre and warning lights will be reset. This works only after you changing the battery.

What kind of battery does Mercedes SLK 230 have?

Mercedes SLK 230: 1999 mercedes slk 230 2.3 supercharged Vehicle… 1999 mercedes slk 230 2.3… Vehicle will not engage starter. No communication to any modules with actron scan tool or snap-on solus pro scan tool. all lights in cluster come on, windows work, radio works. Battery Voltage 12.9 good connections.

Is there a problem with the SLK 230 supercharger?

2002 SLK 32 AMG, bone stock. 1987 190E 2.3-16 valve (destroyed). 2005 E320 new toy. A “problem with the supercharger” isn’t a whole lot of information to go on. That could be a lot of things, or nothing at all. I would suggest that you get the O2 sensor replaced, and then get a second opinion on the blower.

Is the S / C clutch on the SLK 230?

Since you have a pre 2001 model SLK, your S/C has a clutch on it. Post 2000 do not have a clutch on the S/C. Not sure if the P0806 is directly related to S/C clutch, but could be. Others will chime in. FYI- I had the same vague “something wrong with the supercharger” and oxygen sensor failure at about 48k miles.

Is it OK to drive an engine that is misfiring?

Instead from that, misfires can damage other sensors in the engine like the O2 sensors. So, I would never recommend driving an engine that is misfiring for any long distances. Short distances to your mechanic workshop without putting a load on the engine is fine, but do not ignore the misfires and keep driving.

Where can I find the Mercedes Fault code?

Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes. The codes above are retrieved by plugging a diagnostic scanner into the OBD-II port located under the dash, and scanning for fault codes. Location of OBD II port used to retrieve Mercedes-Benz fault codes.

What is fault code b1859 on Mercedes Benz?

There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.

What does it mean if your OBD code is p0513?

Although generic, the specific repair steps may vary depending on make/model. If your OBD II equipped vehicle has exhibited an illuminated malfunction indicator lamp (MIL) accompanied by a stored code P0513, it means that the PCM has detected the presence of an immobilizer key that is does not recognize. This, of course, refers to the ignition key.

Why does my SLK 230 top not retract?

The most common failure is that the rear trunk lifts up and the top unlatches but it does not retract. The motor (pump) continues to run at this point. I would suspect the first switch that the rear lid hits because it is not saying “my trunk is out of the way, you can fold the top down”.

Where is the switch on the SLK 230?

When the trunk lowers, it hits a similar switch in the left side (drivers side for US) near the rear of the trunk under the panel (as i said, similar to the other one). When this is hit, cycle is completed. Similar to going up… BUT, when the final switch is hit, it triggers the small windows to go up.

What does it mean when your transmission says p0720?

You are experiencing transmission problems. You press the gas pedal, and the engine RPMs go up to 4000 or even higher and you are limited to a max speed of about 30 MPH. The check engine light (CEL) comes on. You scan the car using an OBD-II code reader, and you get fault codes such as P0715, P0720, P0700.

What does DTC code p0715 stand for?

Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the input/turbine speed sensor. Quick Tip If you need to get home, try turning off the car. Remove key and wait a couple of minutes then restart the car.

Why is my SLK 230 no start no crank problem?

To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later. Hope this is of interest. Did you clean all 5 connecters before you plugged them in?

How do you get the serial number on a Mercedes Benz radio?

Once you remove your radio or Comand look on the side or back of the radio for the serial code. Call back your dealer and give them the serial code. The code you get from using the serial number should definitively work.

Do you need a radio code for a Mercedes Benz?

If you had a dead battery or replaced the battery, you may need to enter the code in your radio. Follow these steps if you need the Radio Code for your Mercedes-Benz. First take a look at your owners manual booklet. The code may be written down on a small business card size letter.

How do you remove the radio from a Mercedes Benz?

To remove the radio, you will need the radio removal shown below. We found these Mercedes-Benz radio removal tools on Amazon for under $10 and free shipping. Once you remove your radio or Comand look on the side or back of the radio for the serial code. Call back your dealer and give them the serial code.

Where can I get an oil change for my SLK 230?

Most oil change shops or your neighborhood parts store will take your old oil and filter to be recycled properly. The SLK230 has one of the longest drain plugs I have ever seen. Make sure you install your new washer (red arrow) and then the drain plug.

When did the Mercedes Benz SLK Class come out?

In this article, we consider the first-generation Mercedes-Benz SLK-Class (R170), produced from 1996 to 2004.

Can a supercharger be removed from a Mercedes SLK 230?

After watching a YouTube clip of a British mechanic remove the supercharger in a matter of minutes (TV magic?), we decided to attempt a minimalist approach. The upshot: It is possible to jockey an M62 supercharger out of an SLK230 Kompressor (engine 111.973) with the motor mounts and fan/shroud still intact.

How to remove front wheel bearings from SLK R170?

Remove hub Pull out the outer bearing and grab the hub with both hands and remove it. You shouldn’t have to use much force, it will easily come out. Inspect the spindle and bearings Once you remove the hub inspect the old bearings and the spindle.

Why is my fuel light blinking but I have 2 tank of gas?

Had ML in shop this morning for same problem, after stopping truck and restarting, lite off. System showed no codes or problems, customer indicated hard braking and cornering just before lite came on? The Fuel pump assembly does incorporate the sending unit, which tells your dash and trip computer how much gas is left in the tank.

What does the fault code on a Mercedes mean?

Mercedes Fault Code: P261F71 1 Check Engine Light 2 Little to no acceleration 3 Coolant leak 4 Brake Pedal Pressure 5 Engine overheating More …

Why does my check engine light keep blinking?

I am having the same problem with my 2002 ML 500. The light will start blinking then when i tirn the engine off it will go away for a while. Then it will go back on and the check engine light will go on and the trouble could states Evap emmision Large leak. I changed the gas cap bit its still have the same problem. Click to expand…

What’s the problem with the fuel light blinking?

Hello, I have a same problem on my 2002 Ml500, the fuel light starts blinking but I definately have a full tank and I chagned the fuel cap. Everytime I turned on the engine and run for 10 to 15 miles, then fuel light starts Blinking. I turned the enginee off the fuel Blinking gone. Anyone have thoughts on this? Thanks.

What to do if your SLK Class R170 has a leak?

Changing the SLK230 MAF sensor is easy with our handy replacement guide. Got a leak in your exhaust manifold? Fix it with this tech article. ABS warning light blinking?

Why is my Mercedes SLK Class not working?

If one of your car’s electrical accessories isn’t working a bad relay may be the cause. Learn to replace it with this tech article. If your headlights aren’t working after replacing the bulbs and fuse, it may be time to replace the headlight switch.

When does DTC put a car in limp mode?

When the engine control module, transmission control module or brake control unit (ABS) detects a problem in the engine, transmission or with the brake system, it will store a trouble code in your DTC memory. If one of the control units decide that the problem is dangerous for the engine or transmission, it will put the car into limp mode.

How do you change transmission fluid on a Mercedes SLK 230?

On these cars, rotate the crankshaft clockwise with a 27mm socket until the torque converter’s plug is visible in the access window. If the torque converter has a plug, drain it, and then replace the plug, installing a new sealing washer first. Otherwise, move to the transmission pan’s plug.

How do you remove Pan from Mercedes SLK 230?

One trick is to leave the front right bolt (the one attached to the heat shield) halfway in to allow the pan to tilt, draining most of the trapped ATF out the hole. Six M6x40mm bolts, each with a metal clip, hold the pan on the transmission. Their Torx heads often strip during pan removal.

What does ABS Bas ASR light on Mercedes mean?

What do ABS BAS ASR lights mean? If any of these lights turns on and stay ON once you start to drive the car it means there is a problem with one of the following systems or related sensors. Step 1: Ensure that the main battery on your Mercedes-Benz is holding a proper charge. Mercedes-Benz cars are very sensitive to low voltage.

Why does my Bas light come on in my Mercedes Benz?

To reset the lights, start up your Mercedes-Benz and turn the steering wheel all the way to the right, then all the way to the left. Do this a couple of times. Turn off the engine. Restart. Brake Light Switch may cause BAS / ESP / ABS light to come on. It is the most common problem with Mercedes-Benz cars.

In this article, we consider the first-generation Mercedes-Benz SLK-Class (R170), produced from 1996 to 2004.

What does Bas ESP ABS mean on a Mercedes Benz?

What does BAS ESP ABS light mean on a Mercedes-Benz? Let’s first take a look at what each of these acronyms means. BAS stands for Brake Assist System. It provides additional braking power in case of emergency situations.

Can a failed ABS sensor trigger the Bas light?

If you have an ABS sensor that has failed, it will also trigger the ABS, ESP, BAS light. Because the ESP system depends on the ABS system to function properly, the ESP system will also get disabled.

What is fault code for SLK engine management light?

If the CEL is on, you’ve just got to read the codes, specially if recent work has been done on it (ie the MAF). I don’t like this advice of ‘ignore until it goes bust’. Specially from a garage which has just fixed an issue. They should at least do another diagnostic for you. The fault code is P23036 or something like that.

Where is the O2 sensor on a SLK?

Stab in the dark, two rubber pipes under the inlet manifold into cylinder head and down into one valve have perished. And or the O2 sensor is on its way out. Click to expand… Of course, if its P203B that relates to the throttle (so do check what jibcl500 is suggesting since its all related).

What is the fault code for Mercedes Bank 2 sensor?

P0153 O2 Sensor Circuit Slow Response (Bank 2 Sensor 1) P0154 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 1) P0155 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1) P0156 O2 Sensor Circuit Malfunction (Bank 2 Sensor 2)

What is the fault code for a D2B ring?

N1141 MCS fault code: Set-actual configuration of D2B ring differs from actual. N1241 CD fault, CD can not be read. 9260 SRS: resistance in drivers airbag too high. Replace Wiring. Please post a link to this string of posts in the Useful W163 Documents and the DIY Stickys at the top of this forum. done. good stuff.. Anyone know anything about it?

Navigation