How often should I replace my timing belt?

How often should I replace my timing belt?

You can do a visual check – see if there’s any cracking, glazing, missing teeth or oil contamination. Or you can have a mechanic check the belt for you. Most vehicle manufacturers also recommend that you make timing belt replacement a part of your routine maintenance, replacing it every 60,000 miles. Some belts are good for up to 100,000 miles.

What happens when the timing belt breaks on a car?

The level of damage caused by a broken timing belt can depend on the type of engine you have in your car. A non-interference engine provides clearance between the valves and pistons, so if the timing belt breaks, you might end up with bent valves, and you might have to have your cylinder heads rebuilt, but the engine isn’t likely to be destroyed.

Which is more important the camshaft or the timing belt?

Let’s state it plainly – nothing is more important than the timing belt. It drives the camshaft, which is what keeps the valves synchronized, and the crankshaft, which controls the pistons. Your timing belt tells the pistons when to rise and fall, and the valves when to open and close.

What should I do if my timing belt snaps?

Timing belts don’t often give you a lot of warning when they’re about to give way – they might squeak or chirp, or they might just suddenly break. More often, though, damage is due to wear in the timing belt. You can do a visual check – see if there’s any cracking, glazing, missing teeth or oil contamination.

Even if your timing belt isn’t looking all that bad, it should still be replaced approximately every 60,000 miles. Sometimes, signs of wear aren’t immediately apparent. When you replace the timing belt and tensioner, your mechanic may also recommend replacing the idlers and the water pump.

What’s the best maintenance schedule for a Honda CRV?

With that said, the recommended CR-V schedule is as follows: 7,500 – 22,500 – 37,500 – 52,500 – 67,500 – 82,500 miles Check and replace fluids Change oil and filter

What happens when your timing belt goes off?

In a worst-case scenario, your timing belt may ‘jump’. This means that the belt jumps a tooth on one of the pulleys it runs around. The timing will be off and the components inside the engine will not be in the right position at the right time. Over time the timing belt can and will wear.

What’s the difference between timing belt and timing chain?

When an engine has a larger bore and stroke, most automotive manufacturers utilize a timing chain system that replaces the rubber belt with a metal chain. Generally, timing chains last longer than timing belts, with some rated to last the lifetime of the car.

Is there a timing belt on a Honda CRV?

Here is a list of timing belts and timing chains for a Honda CRV. Reference the model year with the corresponding engine to see if your car has a belt or a chain. .

How often do timing belts need to be replaced?

Timing chains do go bad, but they last a long time. Timing belts typically are replaced at 60K or 90K miles for example. Depends on the vehicle manufacturer, and a lot of them are going away from belts and back to chains.

How concerned should I be about 100, 000 / timing chain replacement?

How concerned should I be about 100,000/timing chain replacement? So, my 2011 Honda CR-V (4 door), just crossed over the infamous 100,000 mile mark last Friday.

Can a belt failure cause a timing chain to fail?

Depends on the vehicle manufacturer, and a lot of them are going away from belts and back to chains. GOF – Yes, it is an interference engine. Lots of stories here of kissed valves and broken engines due to timing chain/belt failures.

Once you know, you can determine your Kia timing belt interval by using the first table and the reference key. Be sure to look at the second table to see whether or not the engine is interference-fit. {20} On 1994 models, replace every 60,000 miles. On 1995-2005 models except CA, replace every 60,000 miles.

When to replace timing belt on Volkswagen Jetta?

For instance, Toyota recommends that the Camry replace their timing belts after 60,000 miles. If you have a Ford Focus you can expect to replace the timing belt between 60,000 miles and 90,000 miles. The manual for the Volkswagen Jetta says that you can keep your timing belt until 120,000 miles.

When to replace timing belt on Toyota Avalon?

Therefore, timing belts must be replaced on a pre-determined schedule. The question is, what’s the proper time to do so for your specific vehicle? Find your model below: If you’re the owner of an Avalon with a V6, made between 1995 to 2004, the belt should be replaced by 60k miles.

When to replace timing belt on Ford Focus?

If you have a Ford Focus you can expect to replace the timing belt between 60,000 miles and 90,000 miles. The manual for the Volkswagen Jetta says that you can keep your timing belt until 120,000 miles. According to the US Department of Transportation, the average driver in America travels 13500 miles per year.

In some engine design, some other components like the oil pump, water pump, and injection pump are drive by the timing belt. Timing belts can serve for a long period of time before replacement, at least 3 to 5 year which is about 30,000 – 40,000 miles.

Where is the timing belt and drive belt located?

Drive belt and timing belt both are located in the engine but a few functionalities separate them from each other. So, what exactly is up with Drive Belt Vs Timing belt?

Can a timing belt be replaced with a water pump?

Many automotive repair centers will just replace the timing belt. Getting to the timing belt and replacing it is a very labor intensive process. During a timing belt replacement, the area deep in the engine where the water pump is located is easily accessible.

What causes a timing belt to go wrong?

Timing belt drive alignment is one of the most common causes of drive performance problems. Misaligned drives can show symptoms such as: Parallel misalignment is where the driver and driven shafts are parallel but the driver and driven timing belt pulleys on these shafts lie in different planes.