How much torque does a Land Rover have?
Tighten the bolt to 25 Nm (18 lb.ft). 12 . Secure the LH stabilizer link. Tighten the nut to 115 Nm (85 lb.ft). 13 . Tighten the halfshaft retaining nut to 350 Nm (258 lb.ft). Stake the nut to the halfshaft. 14 . 466 mm (18.34”). 15 . Tighten the lower arm bolts to 275 Nm (203 lb.ft). Align the bolts to the marks made previously.
How do you Torque a Range Rover lower arm?
Using the special tools, install the lower arm rear bushings. 2 . CAUTION: Make sure the bush is correctly aligned. 3 . Install the LH lower arm. Fit the bolts but do not fully tighten at this stage. 4 . Connect the shock absorber and spring assembly to the lower arm. Tighten the nut and bolt to 300 Nm (221 lb.ft). 5 . Release the halfshaft. 6 .
How do you install head bolts on a Land Rover?
1. Lightly oil the threads of the new cylinder bolts, also apply some oil to the under side of the head bolts. 2. Install the bolts: Long bolts 1, 3 and 5. Short bolts 2, 4, 6, 7, 8, 9 and 10 (refer to diagram).
Do you need a head gasket for a Land Rover?
I’m installing a head gasket.Thanks Hi, I do not have these hand at the moment but will post them to you tommorrow. Have you had the head skimmed, and pressure tested?? If not get it done to save yourself the grief of having to take it off again if it is cracked or warped. For all your TD5 torque needs…….
How does torque work on a Land Rover?
Torque values are given by Land Rover for specific nuts and bolts around the vehicle to ensure that they do not come loose during use. Torque wrenches can deviate over time so should be recalibrated regularly to ensure their torque settings are correct. Where no torque value is given, the following settings should be used.
How manybhp does a Land Rover 2.5na have?
Coming from the factory with just 67bhp and 114lb.ft of torque, it gave little increase over the series 2.25 diesel engines (60bhp and 103lb.ft). By comparison the 2.25 petrol engine fitted to earlier models made 74bhp and 120lb.ft!
1. Lightly oil the threads of the new cylinder bolts, also apply some oil to the under side of the head bolts. 2. Install the bolts: Long bolts 1, 3 and 5. Short bolts 2, 4, 6, 7, 8, 9 and 10 (refer to diagram).
Where is the Max fuel screw on a Land Rover?
The max fuel screw is located on the side of the pump closest to the engine as shown in the picture, mine was covered in a wired-up casing presumably to stop any adjustments being made, this was swiftly removed! Where the screw meets the pump housing there is a 13mm nut, this needs to be unscrewed counter-clockwise approximately 2mm to begin with.
What are the specs of a 2010 Range Rover Sport?
▼ 2010 Range Rover Sport 3.0 TDV6 HSE (aut. 6) (model since mid-year 2010 for Europe ) car specifications & performance data review Specs datasheet with technical data and performance data plus an analysis of the direct market competition of Range Rover Sport 3.0 TDV6 HSE (aut.
What kind of engine does a Range Rover Sport have?
6) in 2010 the model with 5-door station wagon body and V-6 2993 cm3 / 182.8 cui engine size, 180 kW / 245 PS / 241 hp (ECE) of power, 600 Nm / 442 lb-ft of torque, 6-speed automatic with CommandShift manual shift mode powertrain offered since mid-year 2010 for Europe .