How do you take the thermostat out of a water pump?
To get the thermostat out, you need to remove the two 10mm bolts that fasten the water pump to the thermostat. This is where extensions for your ratchet come in handy if you have them.
Why is my water pump and thermostat not working?
The radiator, water pump, and thermostat are definite possibilities, but there are a few others that are possible also. A faulty cooling fan is the first thing that comes to mind, but it could also be a head gasket issue, clogged coolant passages inside the engine, or faulty radiator hoses.
How to replace water pump and thermostat on BMW N54?
To do so, remove the four 13mm nuts that hold the sway bar mounts in place. Once those are off, the sway bar should just lower out of the way. There are numerous hoses and connectors on both the water pump and the thermostat. Simple remove these and disconnect the crossover hose that goes from the water pump to the thermostat.
Why is my new water pump still overheating?
Replaced water pump, radiator and thermostat car is still… Q: Replaced water pump, radiator and thermostat car is still overheating. What can it be? Changed water pump, radiator and thermostat. Car still overheating it has a leak in the headers and i am getting that replaced too.
The radiator, water pump, and thermostat are definite possibilities, but there are a few others that are possible also. A faulty cooling fan is the first thing that comes to mind, but it could also be a head gasket issue, clogged coolant passages inside the engine, or faulty radiator hoses.
How much does it cost to replace a Honda water pump?
Many Honda owners, however, opt to replace the water pump together with the timing belt because if the water pump fails later it will cost the same labor to replace. Plus, a water pump is not a very expensive part ($45-$170).
What happens when you replace your water pump?
Overheating after replacing water pump, thermostat and co… Q: Overheating after replacing water pump, thermostat and coolant temp. Sensor I was driving my truck one day and noticed that the temp gauge was raising as I got home, I turned the engine off and check the engine and noticed that the water pump was leaking, it had a hole on it, how?
Replaced water pump, radiator and thermostat car is still… Q: Replaced water pump, radiator and thermostat car is still overheating. What can it be? Changed water pump, radiator and thermostat. Car still overheating it has a leak in the headers and i am getting that replaced too.
Overheating after replacing water pump, thermostat and co… Q: Overheating after replacing water pump, thermostat and coolant temp. Sensor I was driving my truck one day and noticed that the temp gauge was raising as I got home, I turned the engine off and check the engine and noticed that the water pump was leaking, it had a hole on it, how?
What should I do if my water pump is overheating?
Was raising out of nowhere, so I parked and turned it off, let it cool of 10 mins and turned it back on but it was still hot but the coolant was cooling the engine to normal temp. Then it was fine, it keeps doing that randomly so I replaced the thermostat and the coolant temp.
What to do if your water pump overheats?
Place a funnel into the upper radiator hose. Important:Use a 50/50 mixture of antifreeze (refer to vehicle service manual for correct coolant) and deionized water. 4. Slowly fill the cooling system through the upper radiator hose with a 50/50 coolant mixture until the coolant comes out the coolant air bleed hose. 5.
How do you replace a BMW F30 water pump?
Use a T30 bit socket to remove the coolant flange’s bolts. Wiggle the flange around to break the seal of the o-ring, and then pull the flange out of the head. Head back to the thermostat and disconnect the wiring harness from the coolant temperature sensor. Then, remove the thermostat’s two mounting bolts with a T30 bit socket.
What should I use to cool my Car after replacing the water pump?
Important:Use a 50/50 mixture of antifreeze (refer to vehicle service manual for correct coolant) and deionized water. 4. Slowly fill the cooling system through the upper radiator hose with a 50/50 coolant mixture until the coolant comes out the coolant air bleed hose. 5. Connect the upper radiator hose to the radiator. 6.
How do you replace the thermostat on a BMW N20?
Press the flange into the head and thread in its two mounting bolts by hand. Use a T30 bit socket to tighten the bolts. Slip the lower portion of the hose over the thermostat and secure it with its hose clamp. Finally, refit the PCV hose to the engine. Clip in both ends of the hose and plug in the electrical connection.