How do you reset the ABS light on a Honda Odyssey?
1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3. Ground terminal 9 of Data Link Connector with a suitable harness. 4. Turn ignition switch ON while grounding terminal 9. Do not depress brake pedal. 5. After 3.0 seconds, the warning lamp starts flashing to indicate the malfunction code No. (See NOTE.)
How do you change the brake light switch?
Rotate the switch in the clockwise direction to lock it in place. Note: While installing the switch you may have to press down on the brake pedal in order to insert it all the way. Step 3: Reconnect the battery. Now that the new switch is installed, reconnect the wiring harness and negative cable on the battery.
When does the brake light sensor turn on?
Bottom line, this sensor activates the brake lights when the brake pedal is depressed. (B) Choosing the best oil filter: Wix XP / Amsoil / Royal Purple.. Any attempt to repair automotive parts and/or systems carries risk of personal injury. Always adhere and follow safe practices when working on vehicles.
Where is the warning light on Honda Odyssey?
When a problem occurs in the ABS, the warning lamp on the instrument panel comes on. To start the self diagnostic results mode, ground the self-diagnostic (check) terminal located on Data Link Connector. The location of the malfunction is indicated by the warning lamp flashing. 1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2.
What to do if your Honda Odyssey has a malfunction?
The location of the malfunction is indicated by the warning lamp flashing. 1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3. Ground terminal 9 of Data Link Connector with a suitable harness. 4. Turn ignition switch ON while grounding terminal 9.
What are the symptoms of a bad ABS wheel speed sensor?
Symptoms of a Bad ABS Wheel Speed Sensor. 1 Illuminated Warning Lights. Your dashboard contains a variety of important lights that alert you to danger. When the ABS wheel speed sensor fails, you 2 Loss of Anti-lock Brakes. 3 Loss of Traction or Stability Control.
What does the ABS light mean on a Honda Odyssey?
Your Honda Odyssey’s ABS Light comes on when it fails a self diagnostic cycle. When on, it indicates that the Odyssey does not have Anti-Lock brakes, and the safety they provide. Your Odyssey’s ABS system uses a system of sensors to determine wheel speed when braking.
How to find fault code on Honda ABS?
If the ABS warning light goes out for 3.6 seconds then comes back on but does not flash there are NO fault codes present 5 If the ABS warning light flashes, read codes as described in the Code Format Description below. 6 Press the continue button to enter the code numbers and get the code description. • Code sequence begins with a 2 second flash.
What to do if your Honda ABS goes out?
1 Drive the vehicle faster than 30kph for at least 1 minute. 2 Stop vehicle and turn ignition OFF. 3 Connect the terminals with your own wire link, (Click here for details) , as shown on the diagram. 4 Turn ignition ON. If the ABS warning light goes out for 3.6 seconds then comes back on but does not flash there are NO fault codes present
What are the codes on a Honda Odyssey?
• Once every code has been displayed the code sequence repeats. • Code Format Diagram shows code No. 12. The example model (s) shown, Honda CR-V, Odyssey for this auto repair service are only an indication to help you. There may be many other models that apply to this connector.
How do I get my Honda ABS to go off?
Now put your foot on the brake pedal and hold it down lightly while turning on the ignition switch to position “II” (all the dash lights come on, but don’t start it). The ABS indicator will come on, but then should go off, at this point release the brake pedal (some have found better success by releasing the pedal quickly after the light comes on).
How to fault reset Honda ABS and VSA?
Honda ABS / VSA Fault Reset Procedure: Turn the Ignition switch OFF and take the key out. Short pins 4 and 9 on the OBD connector located under the dash on the driver side. Now put your foot on the brake pedal and hold it down lightly while turning on the ignition switch to position “II” (all the dash lights come on, but don’t start it).
What should I do when my abs light goes off?
The ABS light should come on again, press the brake pedal again and hold down lightly. The ABS light should go off again, release the brake pedal (some have found better success by releasing the pedal quickly after the light goes off).
Now put your foot on the brake pedal and hold it down lightly while turning on the ignition switch to position “II” (all the dash lights come on, but don’t start it). The ABS indicator will come on, but then should go off, at this point release the brake pedal (some have found better success by releasing the pedal quickly after the light comes on).
Honda ABS / VSA Fault Reset Procedure: Turn the Ignition switch OFF and take the key out. Short pins 4 and 9 on the OBD connector located under the dash on the driver side. Now put your foot on the brake pedal and hold it down lightly while turning on the ignition switch to position “II” (all the dash lights come on, but don’t start it).
Why are the traction control lights on on my Honda Odyssey?
2012 Honda Odyssey EX-L – had issue with ABS and TRaction control lights on, door would not open unless ignition off. This procedure with pin 4 and 9 and light braking worked quickly, thanks. Practiced once, got on 2nd try. If not covered by warranty (or Honda claims damage), Honda wanted $280 just to diagnose.
Why do the lights go off on my Honda Odyssey?
I recently started having this trouble with my 2002 odyssey. The TCS and ABS lights come on and go away intermittently. I took it to the honda dealership and they ran the initial tests and basically cleared the lights. I drove it home no lights, once parked I shut off the engine, restarted it and the lights came back on.
Where are the fuses on a Honda Odyssey?
Check Fuse # 50 (30A) in the Under-hood Fuse/Relay Box. Check ground in the motor power circuit. Check Fuse # 14 (7.5A) in the Passenger’s Under-dash Fuse/Relay Box. Check ground and a loose connection in the Under-dash Fuse/Relay Box and the ABS Control Unit. Check ground in the MCK circuit. Check pump motor relay in the Under-hood ABS Relay Box.
What does it mean when the ABS light blinks twice?
8. After a few seconds, the ABS indicator blinks twice and the DTC is cleared. If the ABS indicator stays on after it blinks twice, check the DTC, because a problem was detected during the initial diagnosis before shifting to DTC clearing mode.
Why are the VSA lights on on my Honda Odyssey?
Power Sliding Doors Won’t Open! Another annoying side effect of the VSA/ABS lights being illuminated (besides the fact that the important safety features of anti-lock braking and stability assist are disabled), is the two power sliding rear doors on the Odyssey will not open with the engine running.
When does the ABS warning light come on?
Anytime a problem occurs in the ABS brake system the warning light gets on. In fact, ABS light stays on unless you fix the core issue. Basically, the warning light alerts the driver that the safety system is no longer active.
Where are the short pins on the OBD?
Short pins 4 and 9 on the OBD connector located under the dash on the driver side. I used a paper clip, but any stiff (solid) light gauge wire will do. Click on the photo below right to expand and you can see the pin numbers marked in the plastic.
Power Sliding Doors Won’t Open! Another annoying side effect of the VSA/ABS lights being illuminated (besides the fact that the important safety features of anti-lock braking and stability assist are disabled), is the two power sliding rear doors on the Odyssey will not open with the engine running.
How can I tell if my ABS sensor is bad?
Warning lights appear on the dashboard: If the ABS computer finds a problem with a wheel speed sensor or its circuit, it will trigger the ABS warning light on the dash. It may also turn on the traction and stability control warning lights, if the car has those systems.
Why does the VSA light keep coming on on Honda Odyssey?
If it stays on, it is letting you know that there is some problem with the Odyssey’s VSA itself. When the light comes on, Honda suggests getting someplace safe and restarting the engine. If the VSA light doesn’t come back on, you are good to go. If it does come back on, it is time to diagnose the issue, or take it in to the shop. 2.
Why do the VSA and ABS lights stay on?
However, even after boosting the battery (we carry a portable booster just for such occasions) and getting the vehicle started, the ABS and VSA dash lights remain illuminated indicating a fault. In this instance, clearly the “fault” is some anomaly caused by the low battery voltage.
Where is self diagnostic results Terminal on Honda Odyssey?
To start the self diagnostic results mode, ground the self-diagnostic (check) terminal located on Data Link Connector. The location of the malfunction is indicated by the warning lamp flashing. 1. Drive vehicle over 30 km/h (19 MPH) for at least one minute. 2. Turn ignition switch OFF. 3.