How do you remove motorcycle fork seals?
How do I change the fork seals on my motorcycle?
- Step 1: Wind off the spring preload and screw down the rebound adjuster.
- Step 2: Loosen the top caps.
- Step 3: Remove the forks.
- Step 4: Remove the bottom bolt.
- Step 5: Drain the old oil.
- Step 6: Remove the dust seal.
- Step 7: Remove the snap ring.
Is it easy to replace fork seals?
Replacing your fork seals is an easy enough job if you know a few tricks. The first step to any DIY job is to do a little research and get all the parts you’ll need for the job. You’ll at least need the new seals and fork oil but should also consider wipers, bushings and any seals or o-rings for the caps.
How do you change fork seals?
Remove the old seal.
- Wedge the dust seal from the fork leg.
- Find the fork seal itself. It is held into place by a clip within a groove.
- Pry the seal out carefully.
- Flush the area as you go to remove debris within the fork.
- Take the tube in 1 hand and the stanchion in the other. Use muscle to pull the 2 apart.
How do you remove a seal from a fork?
Free the damper rod by inserting a tool into the cavity to reach it. Memorize the assembly of the fork’s springs, washers and spacers for easy re-installation later. Remove the old seal. Wedge the dust seal from the fork leg. Find the fork seal itself. It is held into place by a clip within a groove. Pry the seal out carefully.
How do you replace a fork seal in RevZilla?
RevZilla photo. It’s easy to do. Cut off a chunk of 35mm film. Pop your dust boot up. Gently slide the film between the seal and the fork tube. Work it around the seal, up and down, until you get back to where you started.
How to save a fork seal on dirt bike?
How to Save a Fork Seal – 3 Simple Steps to Fix Leaky Dirt Bike Forks!! If playback doesn’t begin shortly, try restarting your device. The Mx Factory is a channel that aims to educate and entertain the world on dirt bikes!
What’s the best way to replace a fork?
Remove the brake calipers, fender, front wheel and any other hanging cables. Disassemble the fork. Loosen the bolts further and pull downward on the fork while twisting. Remove the fork cap carefully. Because it is spring loaded, be careful not to stand in the way of the cap as you remove it.
How do you replace a seal on a front fork?
Barring accident damage, seals are what go out first. To replace a seal you must first drain the fork fluid, if possible, and then remove the front wheel, fender, fork brace (if there is one), and, if the brakes are hydralic, the brake calipers.
What should I do if my fork is not coming out?
If the leg does not want to come out and you have the bolt and circlip out, the problem is a bushing under the fork seal. Push the fork leg in and then pull it out sharply. You may have to do this several times. This will slowly work the seal and bushing out of the fork leg. Clean all the old fluid out of the leg. Slide the old seal off the leg.
How to remove dust seal from fork leg?
1 Wedge the dust seal from the fork leg. 2 Find the fork seal itself. It is held into place by a clip within a groove. 3 Pry the seal out carefully. 4 Flush the area as you go to remove debris within the fork. 5 Take the tube in 1 hand and the stanchion in the other. Use muscle to pull the 2 apart.
How often should you replace Fork seals on a motorcycle?
Have two fork seals at hand; you never know when you’ll ruin one during the install or, more likely, decide the job is so much fun you can’t resist doing the other seal at the same time. Have a sufficient quantity of fresh fork oil at the ready, too. Here are 10 easy steps to walk you through how to replace motorcycle fork seals.