How do you remove a compressor from a Honda Civic?

Disconnect the electrical connector on top of the compressor. From underneath the engine, loosen the 14mm belt adjusting bolt and remove the compressor belt. Figure 2. Loosen the A/C compressor belt. Remove the four 12mm bolts on the side of the compressor that secure it to the engine. Remove the A/C compressor.

What happens when the a / C unit fails on a Honda Civic?

When A/C compressor units fail, the refrigerant is no longer able to stay pressurized and can no longer produce cold air. A/C repair costs are usually in the thousand dollar range, because in most cases, the job is labor intensive. However, Honda Civic owners have it easy when it comes to replacing the A/C compressors themselves.

Where is the a / C drier on a Honda Civic?

The A/C drier keeps moisture from building up inside the system. When the compressor is disconnected, air manages to escape, and moisture can make its way into the system. The drier is located right below the windshield washer reservoir. With your 10mm socket and ratchet, remove the two bolts on top of the drier.

What’s the PSI of the air conditioner in a Honda Civic?

So, back to the hoses. This time, I revved the car up to about 1,500 to 2,000 RPM (since the Civic seems to idle at around 500 rpm). Sure enough, he said that the low pressure was being sucked down to about 20 PSI and the high-pressure was kicking way up again past 400 PSI.

How to replace AC condenser 2001-05 Honda Civic?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: TQHbbfYVYvfHHUoH)

Where is the AC relay on a Honda Accord?

Turn the Honda engine on. Turn the AC settings to “Off.” Open the hood of the Honda vehicle. Locate the AC clutch relay. Trace the wire that runs off the AC compressor; this wire plugs into the clutch relay. The relay is mounted on the firewall.

How can I tell if my AC compressor is on?

Touch the test light lead to the middle of the three wires. The middle wire receives power from the clutch relay. The wire should read “Inactive.”. Turn the AC control to “On.”. Unplug the wire harness from the AC compressor. Touch the test light lead to the middle wire once more. The wire should now read “Hot.”.

How do you remove the belt from an A / C compressor?

With a 10mm socket and ratchet, remove the hose connectors along with the hoses. Disconnect the electrical connector on top of the compressor. From underneath the engine, loosen the 14mm belt adjusting bolt and remove the compressor belt. Figure 2. Loosen the A/C compressor belt.

Where is the air conditioner harness on a Honda Civic?

Locate the main vehicle harness, which is in the front passenger’s side of the engine bay. Remove the plug cap. Plug in the A/C harness connector to the main harness. Mount the harness with the pre-installed bracket. The harness routes through the front of the engine bay—in between the radiator support and headlights. Figure 8.

How do you install a bypass pulley on an AC compressor?

Then remove the compressor drive belt. Remove the compressor, but keep the mounting bolts. Place the bypass pulley in place of the compressor and install the bolts to the proper torque. Re-install the compressor belt and tension properly.

How do you remove an AC compressor from a car?

Remove the negative battery cable from its post. Remove the bolt at the compressor that secures the refrigerant lines and inspect the lines carefully for dirt or signs of wear. Disconnect the compressor’s electrical connections. Remove the compressor’s mounting bolts and pull the unit from the vehicle.

Is there an AC repair on my Honda Civic?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: GGp6kApi4_puvn89)

Navigation