How do you reinstall a clock spring on a car?
Take note of the alignment markers of the clock spring and the steering column shaft. These marks must be close when reinstalling the clock spring. Locate the clock spring mounting screws which will be accessed through a series of small holes. The clock spring outer plate may need to be rotated slightly to access the screws.
Where is the clock spring on a steering wheel?
The clock spring connects to a vehicle’s steering wheel, allowing it to turn while still running the other electronic components. This device is found in the steering wheel of a car, but it also has other uses in technology. In older vehicle models, a clock spring was not necessary since the steering wheel’s only function was to turn the car.
What is the clock spring on an airbag?
Airbag clock spring replacement overview. The clock spring is a special connector that allows the car’s steering wheel to turn while creating a connection with the airbag, horn, and other parts of the car’s electrical system.
Do you need a manual to change a clock spring?
Keep in handy the user manual of your car, as well as the manual that came along with the replacement clock spring you bought, so that if a detail regarding either of the two raises its head, it can be immediately cross-checked. If your car manual includes a procedure to change your spring coil, follow it to the letter.
Where is the clock spring on a car?
The clock spring is usually located on the steering column behind the steering wheel. Almost every road going vehicle with a steering wheel has one of these devices. However, if your vehicle has no airbag, steering wheel controls, or horn buttons, you may not have a clock spring.
What do I need to replace clock spring?
The clock spring has the wiring which controls the Horn, Cruise Control, and the Radio Controls on the steering wheel. There is one special tool needed to remove the air bag. The rest are general tools. I used a TX30 star bit screwdriver which seemed just slightly small but it did get the job done.
Why is my steering wheel dependent on a clock spring?
Because the airbag in your steering wheel is dependent on a functional clock spring, it’s crucial that the clock spring is in good working condition. Keep reading to understand how a clock spring works, what symptoms of a broken clock spring are, and the average replacement cost is. What is a Clock Spring? What Does a Clock Spring Do?
How do you find the center of the clock spring?
Find the center position of the clock spring. You can do this by turning the clock spring all the way to the left and stop as soon as you feel slight resistance. Then turn it all the way to the right and count the total turns. Let’s say you get 6 full turns.
Where to find clock spring on steering column?
Take note of the alignment markers of the clock spring and the steering column shaft. These marks must be close when reinstalling the clock spring. Locate the clock spring mounting screws which will be accessed through a series of small holes.
Where is the clock spring on a Mercedes Benz?
Once you have the steering wheel off, the clock spring is right there. I’m about to have to do this job on my car, and it shows just what you need to do.
Can a clock spring be removed from an airbag?
This is required on some models. Gently work the clock spring back and forth and outward from the steering column shaft and gently remove. Electrical connectors are attached to the bottom of the airbag clock spring to transfer signals and controls to the steering wheel and airbag. This can also be a wiring harness on some models.
How do you remove a clock spring from a car?
The clock spring outer plate may need to be rotated slightly to access the screws. These screws are a number 15 Torx head. Using a Torx head screwdriver or socket to remove the mounting screws by turning them counterclockwise. Use caution as not to drop the crews down inside of the steering column.
Where does the clock spring go on a steering wheel?
4. Remove the Clock Spring: The clock spring sits over the center shaft of the steering column and is held in place by a set of small screws or plastic clips. Once the steering wheel has been removed do not rotate the clock spring upper plate.
What happens when you take off the clock spring?
If you are taking off the clock spring : Mark the clock spring and angle position sensor . If you rotate the angle position sensor when the steering wheel is off and then install the steering wheel. The car will think that you have the steering wheel rotated when you are driving straight.
How do you remove clock from steering column?
Using a small pick or screwdriver to release the plastic retainer clips while pulling the unit outward. This is required on some models. Gently work the clock spring back and forth and outward from the steering column shaft and gently remove.