How do you change the starter on a Dyna Glide?

Remove the seat, typically with just a thumb turn screw at the back of it. Remove the outer battery cover fastener (1) and pull the battery cover (2) away from the battery tray (3). Disconnect both battery cables, beginning with the negative (black) terminal. Undo the battery strap (6) and remove the battery from the battery tray.

What to do if your Dyna bike won’t start?

Apparently, starter issues are quite common on various Dyna models, so if yours is in need of replacement, see How to Replace Starter. If you are in a bind and your starter motor is acting up, a quick tap of the solenoid with a hammer or similar small object can sometimes free the starter to start the bike.

What makes a Harley Dyna hard to start?

1. Spark plugs in bad condition or have improper gap or are partially fouled. 2. Spark plug cables in bad condition. 3. Battery nearly discharged. 4. Loose wire connection at one of the battery terminals, coil or ECM connector. 5. Water or dirt in fuel system. 6. Intake air leak. 7. Fuel tank vent hose and vapor valve plugged. 8.

How does the starter work on a Harley Davidson?

Much like a car, the starter motor on various Harley Davidson models cranks the engine over via a geared shaft that engages the teeth on the clutch sprocket. When battery voltage is supplied to the starter solenoid, the starter interlocks with the clutch sprocket and uses the primary drive setup to spin the engine over.

What should the voltage be on a Harley Davidson Dyna Glide?

Use a voltmeter to measure the available voltage at the battery. A battery that is 100% charged will have approximately 12.6 volts, whereas a battery with a 0% charge will read 11.8 volts or lower. If your battery is low, charge the battery on a setting no higher than five amps for a few hours.

How do you replace a starter on a Harley Davidson?

While the starter can often be replaced with the battery and battery tray in place, Harley recommends they be removed for additional working room. Remove the seat, typically with just a thumb turn screw at the back of it. Remove the outer battery cover fastener (1) and pull the battery cover (2) away from the battery tray (3).

When do you need to replace the starter solenoid?

If you test your starter solenoid and find that it’s bad, you’ll need to replace it in order to start the vehicle again. For further instruction on how to replace the starter solenoid in your specific vehicle, it is recommended that you read the service manual for its specific year, make and model.

How do you replace a starter on a lawn mower?

Using a new starter O-ring, slide the starter into place. Apply Threadlocker (blue) to the mounting bolts and reinsert, tightening until they are sufficiently tight (torque to 27-33 ft/lbs according to the factory). Re-connect the starter solenoid electrical plug.

How do you change the starter in a car?

Step 1 – Lift the hood and remove the negative battery cable from the battery making sure the cable end is clear of the battery to avoid an accidental connection. Step 2 – After the battery has been disconnected, remove all access shielding and covering to expose the starter terminals on the solenoid.

How much does it cost to replace a Honda starter motor?

Many part stores will give you the core charge refund If you return the old starter motor (core). An original or OEM starter motor is more expensive ($270-$480). One of our friends decided to replace the starter motor in his 2014 Honda Accord.

Do you need to remove negative cable to replace car starter?

You only need to remove the negative cable. This is a good move any time you’re working on the car. NOTE: Many vehicles need to be raised up to reach the starter. On others, obtaining starter access can be difficult. Check your vehicle repair manual for location and replacement details.

What do you use to remove solenoid from car starter?

You may need to spray the fasteners with a rust remover like WD40 in order to loosen them. Be careful not to break the bolts as you remove them. Pull the solenoid out away from the starter.

When does the starter motor need to be replaced?

New aftermarket starter motor. In some vehicles with larger engines (e.g. BMW, Cadillac Northstar V8, Toyota V8), an intake manifold or other parts must be removed to get to the starter motor and that will require more labor ($260-$450). An aftermarket starter motor (part) costs $85-$220 plus the core charge.

How to diagnose a car starter motor problem?

When Diagnosing starter motor problems; always start with the battery. For the starter motor to work; make sure that your car battery is in excellent working condition and fully charged. Starter motors are used to rotate an engine to begin the starting process.

Why is my starter not working on my Harley Davidson?

Here’s a Harley Davidson starter issue that can have a simple solution. We talked about the electrical circuits on our motorcycles and this is a good example of how the mechanical component might not be working even if the electrical component is. The starter sprag clutch is an easy fix and we show you how it’s done.

How much does it cost to replace a starter clutch on a Harley?

This starter clutch, however, will cost us a little more than its predecessor. How long it takes to replace your Harley starter clutch will simply depend on what model HD you own. Once the starter is on the bench, it is a quick, easy process to separate the gear housing section of the starter from the motor and solenoid sections.

How to replace the battery on a Harley Davidson Dyna Glide?

Harley Davidson Dyna Glide: How to Replace Battery. 1 Step 1 – Loosen the battery cover/support. Loosen the battery cover/support and slide it outboard. The battery cover/support looks like a rectangular 2 Step 2 – Disconnect the old battery. 3 Step 3 – Install and connect the new battery. 4 Step 4 – Tighten the battery cover/support.

Where is the drain plug on a Dyna Glide?

Remove the primary drain plug located at the rear of the primary cover and allow the oil to drain into a suitable catch-pan. Be sure to retrieve the drain plug O-ring. Figure 2. Draining primary oil. After the oil has drained, remove the primary cover fasteners.

How often should I Change my Harley Davidson battery?

When they do die, it can be a major bummer. It is easy to avoid this issue by changing your battery regularly. I recommend changing your battery every three to four years at a minimum, so you don’t end up stranded somewhere. Like most things, all batteries are not created equal.

Can you remove the seat from a Dyna Wide Glide?

Removing the seat from your motorcycle for the first time can be a bigger challenge than it should be. Harley-Davidson’s Dyna Wide Glide offers a unique challenge, as the sissy bar — the passenger back rest — seems to forestall any apparent possibility of removing the seat without taking the sissy bar off as well.

When did the Harley Davidson Dyna Wide Glide come out?

500cca Lightning Start 12v 20ah WPX20L-LS Ultra High Performance Sealed AGM Motorcycle Battery upgrade replacement for Harley Davidson FXDWG Dyna Wide Glide 1340, 1450, 1584, 1690 for year 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2007, 2008, 2010, 2011, 2012, 2013, 2014.

Harley Starter Clutch Replacement. Once the starter is on the bench, it is a quick, easy process to separate the gear housing section of the starter from the motor and solenoid sections. The clutch assembly is held in with only a light, press fit. An internal o- ring assists in keeping it aligned, properly orientated, and sealed within the housing.

How does the starter motor work on a Honda Accord?

When battery voltage is supplied to the starter solenoid, the starter interlocks with the clutch sprocket and uses the primary drive setup to spin the engine over. Unfortunately, cranking over a big V-twin has a tendency to take its toll on the starter motor.

How does a Harley Davidson Dyna Glide starter work?

This article applies to Harley Davidson Dyna Glide models (1996-2016). Much like a car, the starter motor on various Harley Davidson models cranks the engine over via a geared shaft that engages the teeth on the clutch sprocket.

Where is the starter relay on a Harley Davidson?

Can someone please tell me where my bike’s starter relay is located? Some have said it’s back by the battery compartment, others have said it’s between the fuel tanks the only stuff I saw between the fuel tanks were mainly a bunch of wires…..my bike is a 1986 Heritage Softail (1340cc Evo). Any assistance would be greatly appreciated, thanks!

How do you change the battery on a Dyna Glide?

Remove the outer battery cover fastener (1) and pull the battery cover (2) away from the battery tray (3). Disconnect both battery cables, beginning with the negative (black) terminal. Undo the battery strap (6) and remove the battery from the battery tray. With the battery removed, undo the battery tray fastening screws.

What is a good high torque starter for 06 Electra Glide?

Regardless have been looking at starters and there are so many options. Does anyone have a recommendation on a good high torque starter for 06 electra glide beefed up to a 107″ Thanks in advance. When I purchased my new ‘08 Ultra I had it upgraded to 103 with cams and fought hard starting for many years.

1993: The Dyna Low Rider and Dyna Wide Glide are introduced, the two among the most popular Dyna models throughout the frame’s 26 year production run. 1995: Until this year, all Dynas had a 32-degree front rake, but in 1995 a more responsive 28-degree rake was introduced to the sportier Dyna models.

What to do if your Dyna Glide won’t start?

Typical Dyna Glide fuse box layout. It usually a good idea to open up the right handlebar switch assembly and check for corrosion on the starter and run switches. While it is not a very common problem, checking for a faulty starter switch is one last area to inspect before setting your sights on the starter assembly itself. Figure 6.

When did the starter change on a Harley Davidson?

Harley’s starter design changed in 2007 and we found ourselves no longer having to get into the primary drive to repair or replace a starter! Prior to 2007, the starter clutch and the starter gear were two separate parts. Harley has since changed the design.

Can a stator be removed from a Harley Davidson?

Mike demonstrates Harley Davidson stator and rotor removal so we can replace it with a 50 amp upgrade. Follow along. There are plenty of tips along the way. Did you test your system?

How do you close the modal on a Harley Davidson?

This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. Sign up for premium membership and get access to our best Harley repair videos and step-by-step instructional projects.

Navigation