Can you change the front wheel bearing on a Saturn?
Backyard mechanics can change the front wheel bearing on a 2002 Saturn in a few hours with the right tools to separate the suspension components. However, the hub must be forced in and out of the steering knuckle with a hydraulic press.
How do you put a new bearing hub on a car?
Place the new bearing hub into the center of the steering knuckle and use the press to force the hub into the knuckle. Push the retaining ring into the center of the steering knuckle to secure the bearing hub. Slide the hub onto the drive-axle shaft.
How do you remove a wheel hub from a car?
Pull the cotter pin from the end of the stud on the lower control arm. Remove the retaining nut on the end of the stud with a socket wrench. Place a metal punch against the end of the drive-axle shaft and hit the punch with a hammer to detach the wheel hub from the shaft. Remove the steering knuckle.
How do you tighten a hub nut on a car?
Attach the ABS speed sensor electrical connector to the harness. Place the hub washer and hub nut onto the drive axle shaft. Tighten the hub nut with a torque wrench. Place a large pry bar between the lug studs and wedge the other end under the frame to stop the shaft from turning. Tighten the hub nut to 145 ft.-lbs.
Backyard mechanics can change the front wheel bearing on a 2002 Saturn in a few hours with the right tools to separate the suspension components. However, the hub must be forced in and out of the steering knuckle with a hydraulic press.
Place the new bearing hub into the center of the steering knuckle and use the press to force the hub into the knuckle. Push the retaining ring into the center of the steering knuckle to secure the bearing hub. Slide the hub onto the drive-axle shaft.
Pull the cotter pin from the end of the stud on the lower control arm. Remove the retaining nut on the end of the stud with a socket wrench. Place a metal punch against the end of the drive-axle shaft and hit the punch with a hammer to detach the wheel hub from the shaft. Remove the steering knuckle.
Attach the ABS speed sensor electrical connector to the harness. Place the hub washer and hub nut onto the drive axle shaft. Tighten the hub nut with a torque wrench. Place a large pry bar between the lug studs and wedge the other end under the frame to stop the shaft from turning. Tighten the hub nut to 145 ft.-lbs.
Backyard mechanics can change the front wheel bearing on a 2002 Saturn in a few hours with the right tools to separate the suspension components. However, the hub must be forced in and out of the steering knuckle with a hydraulic press. Most machines shops will remove and install the bearing hub inside the steering knuckle for a small fee.
What kind of car was the Saturn’s series?
The Saturn S-series was a family of compact cars from the Saturn automobile company of General Motors. Saturn pioneered the brand-wide “no haggle” sales technique.
What was the trim level for the Saturn L series?
The L series had also adopted a type of a trim level structure that was similar to the trim level structure on the Saturn ION. The L300 sedan and the L300 station wagon models both used the L300.1, the L300.2, and the L300.3 for both the L300 sedan and the L300 station wagon models.
What was the first generation of Saturn SC1?
The first generation Saturn SC1 coupes shared the same fixed headlight front fascia as the SL sedans and the SW station wagons, rather than the pop-up headlight design used on the SC2 and the original SC. The SC1 also lacked a rear trunk lid reflector and a rear stabilizer bar.
Are there any problems with the Saturn’s series?
Saturn experimented with making these out of plastic, it was a huge failure. ALL of them failed, if you still own one of these cars and it hasn’t been replaced, it has failed. Symptoms include hard starting, rough idle, temperature gauge not working, awful fuel economy, poor performance, and stumbling, among many other things.
Why does my Saturn Vue make a grinding noise?
I have a 2007 saturn vue 4 cylinder .Ihave a low grinding noise fromthe front end I believe may be the wheel berrings or the front pads or rotors. There is a vibration on the accelerator pedal as i dr … read more 1997 saturn: ~100K miles and has developed a leaky sunroof. I have an opportunity to repurchase my 1997 Saturn SC1.
Why are my coil springs broken on my Saturn s?
-Broken coil springs in 3rd generation (00-02) cars. If you’re doing struts, replace the springs. OE junkyard replacements from a gen-1 or gen-2 car are your best bet. This is caused mainly by overdrawing from the 12v socket, or high power aftermarket accessories drawing from the same circuit.
What causes a Saturn’s to slam into reverse?
This causes the car to “slam” into reverse and/or harsh upshifts, depending on which is worn. It will eventually destroy the line pressure solenoid, which will make for very hard upshifts. If left for a while, it will knock the input shaft nut loose, further worsening the condition of the shifts.