What is a track bar on a Jeep TJ?
Jeep Wrangler TJ track bars are simple devices that connect one end of the axel to the frame of the chassis on the other side of the vehicle. The pivots of the track bar allow either end to swivel up and down, but not side to side.
What is the bar on the front of a jeep called?
It’s called a stinger. It’s supposed to prevent you from flopping forward when coming off a steep decline, but mainly it’s for looks.
What front axle is in my Jeep TJ?
TJ Wranglers will have either a Dana 30 in the front and a Dana 35 in the rear unless you have a Rubicon model. In which case you’ll have 44s front and back.
What is a 2003 Jeep Wrangler called?
The Jeep Wrangler (TJ) is the second generation of the Jeep Wrangler off-road and sport utility vehicle….Jeep Wrangler (TJ)
| Jeep Wrangler TJ | |
|---|---|
| Length | 1996–99: 151.2 in (3,840 mm) 1999–2003: 155.4 in (3,947 mm) 2004–06 SWB: 154.9 in (3,934 mm) 2004–06 LWB: 171 in (4,343 mm) |
Where are the track bars on a Jeep Wrangler?
Jeep Wrangler Track Bar kits. The factory Track bars locate the body in relation to the axle. It is located at the framerails and runs down to the axles. When a jeep is lifted, the axles shift sideways.
What kind of drivetrain does a Wrangler have?
A Wrangler’s drivetrain is its bread and butter. That said, there is always room for improvement, or to hone it to your off-road needs. Stronger axles, different gear ratios, and even a tougher differential will help you tackle more difficult trails. Wranglers are known to have a terrain capable and rugged drivetrain.
What are the bushings on a Jeep Wrangler?
The bushings, usually polyurethane, are made to preserve the track bar, allowing some flex between the collar and the track bar. If your bushings are old and dry rotted, they will not be doing any good. The bushings may provide excessive flexing of the track bar and cause the dreaded death wobble. The collars separate the bolt from the bushing.
Which is the best rear axle for a Jeep Wrangler?
The Dana 30 will only be found as a Jeep front axle while the Dana 35 will only be found as a rear axle on Wranglers. Dana 35 axles have earned a very poor reputation in the off-roading world, however, it is a great axle for stock Wranglers.
What kind of track bar do you need on a Jeep Wrangler?
Lifted Jeeps require longer track bars while normal Wranglers can stick to the regular length bars. Make sure you get the right track bar length/adjuster that is compatible with your lift size. After removing the old track bar and before installing the new one, you need to center the axle.
What causes the track bar to wobble on a Jeep Wrangler?
Preventing Death Wobble & Jeep Wrangler Track Bar Replacement. The Jeep Wrangler death wobble refers to a vibration that can be caused by your track bar bushings, collars, or brackets which makes the axle want to free itself from your Wrangler. Check out the track bar bushings.
The bushings, usually polyurethane, are made to preserve the track bar, allowing some flex between the collar and the track bar. If your bushings are old and dry rotted, they will not be doing any good. The bushings may provide excessive flexing of the track bar and cause the dreaded death wobble. The collars separate the bolt from the bushing.
What kind of 4 wheel drive does a Jeep Wrangler have?
In 4WD Low mode, the clutch pack is locked and power flows through a 2.72:1 planetary gear set for higher torque at lower speeds. The 2018 and newer JL Wrangler comes by default with Command-Trac, but its Sahara trim can be upgraded to Selec-Trac II, marketed as simply Selec-Trac, utilizing the MP3022 transfer case.