How do you replace brake pads on a Jeep Cherokee?
Insert the two new brake pads in to the bracket with the wear bars situated at the bottom of both the inner and outer pads. Push the pads together until they are flush against the rotor. Swing the caliper down over the new brake pads and in to the bracket.
How do you remove rotors from brake pads?
Once the pads are off, remove the rotor. On many vehicles, you’ll need to remove the caliper mounting bracket in order to remove the rotor. The brake caliper bolts to the brake caliper mounting bracket which bolts to the spindle assembly. To remove the brake rotor, first remove the brake caliper and then remove the brake caliper bracket.
What kind of brake caliper does a Jeep Cherokee have?
The Cherokee is equipped with a “screw-in” type rear caliper piston. An optional item you may want to purchase for this procedure is a brake caliper piston tool. I found it relatively easy to wind back the rear caliper piston by using a pair of needle nose pliers.
How much does it cost to replace a brake rotor?
Brake rotor and pad repair generally comes out to around $250 to $500 per axle when visiting a professional shop. Calipers are the most difficult and expensive aspect of the braking system to replace. A single caliper can cost up to $130 and several will reach prices even higher.
When to replace the brake pads on a Jeep Cherokee?
If your Cherokee previously exhibited shuddering, pulsations, or vibrations in the rear end during braking, you may need to have your rotors “turned” (resurfaced) or just replace them with brand new rotors.
How do you replace a brake rotor at Advance Auto Parts?
You may need to compress the caliper piston in order for the caliper to slide back on the rotor. Use a c-clamp or caliper spreading tool—borrow one for free at your local Advance Auto Parts. If you use a c-clamp, position the clamp on an old brake pad and the back of the caliper’s piston, then tighten.
The Cherokee is equipped with a “screw-in” type rear caliper piston. An optional item you may want to purchase for this procedure is a brake caliper piston tool. I found it relatively easy to wind back the rear caliper piston by using a pair of needle nose pliers.
How do you reset a parking brake rotor?
If a brake caliper utilizes a parking brake mechanism, a caliper reset tool is needed. Step 16 – Once the caliper has been retracted, insert the caliper mounting bracket over the rotor. Step 17 – After fitting the caliper bracket into place, insert the mounting bolts and tighten.
What kind of brake rotor do I need for my Jeep Cherokee?
Your Jeep Cherokee goes everywhere, but not without the right set of brakes. At AutoZone, we specialize in high-carbon brake rotors for Jeep Cherokee that are precisely machined to match your Jeep’s signature versatility, providing long-lasting performance both on and off the road.
How do you replace rear disc brake pads?
If your new set of rear pads includes replacement brake hardware, pull the old metal pad abutment or “anti-rattle” clips out of the top and bottom of the bracket. Apply a thin layer of brake caliper grease to the to new pad abutment clips where they will come in contact with the bracket or the new brake pads.
Where is the EPB on a Jeep Cherokee?
Push the lower pin back in to its rubber dust boot at the bottom of the bracket. Attention : If your Cherokee is equipped with an electronic parking brake or “EPB”, you must place it in “service” / “maintenance” mode by using the display screen on the dashboard as shown at the top of this page.
To remove the existing rotors and install new ones, remove the two bolts on the rear of the caliper bracket that attach it to the steering knuckle. Then loosen the old rotor with a rubber mallet, pull it off, and slide the new one in its place. I’ve had good luck with the Wagner ZD1734 ceramic brake pads.
How to replace rear brake pads and rotors?
Step 5 – Using a pair of dikes remove the rotor retainer clip which is used in initial assembly and will not be reinstalled. Step 6 – Next, use a socket to remove both upper and lower caliper mounting bolts. Use a wrench if necessary to secure the slide.
Why is my park brake not working on my Jeep Cherokee?
If the electric park brake (EPB) switch is actuated with the caliper removed from the caliper bracket and still connected electrically, the EPB motor will fully extend causing damage to the caliper piston. Disconnect and isolate the negative battery cable before servicing any EPB component.
To remove the existing rotors and install new ones, remove the two bolts on the rear of the caliper bracket that attach it to the steering knuckle. Then loosen the old rotor with a rubber mallet, pull it off, and slide the new one in its place. I’ve had good luck with the Wagner ZD1734 ceramic brake pads.
If your new set of rear pads includes replacement brake hardware, pull the old metal pad abutment or “anti-rattle” clips out of the top and bottom of the bracket. Apply a thin layer of brake caliper grease to the to new pad abutment clips where they will come in contact with the bracket or the new brake pads.
Push the lower pin back in to its rubber dust boot at the bottom of the bracket. Attention : If your Cherokee is equipped with an electronic parking brake or “EPB”, you must place it in “service” / “maintenance” mode by using the display screen on the dashboard as shown at the top of this page.
How do you Grease a new brake caliper?
Apply a thin layer of brake caliper grease to the to new pad abutment clips where they will come in contact with the bracket or the new brake pads. Push the new pad abutment clips in to the top and bottom of the bracket. In order for the brake caliper to operate smoothly, the two caliper slider pins need to be well lubricated.