What kind of fuel pump does a 1993 Jeep Grand Cherokee use?

Your 1993 Jeep Grand Cherokee uses an electric in-tank fuel pump. However, you do not need to lower the tank to replace a failed pump, which makes it relatively easy to replace. Still, you want to make sure the O-ring under the sending unit assembly, which contains the fuel pump, seals properly.

Where is the fuel pump on a jeep?

To be absolutely sure, raise and support the back of the Jeep on jack stands, unless the height allows you to crawl under the back without raising it. Unplug the fuel pump connector at the back of the fuel tank. It will be easy to find and has four wires in the connector.

How can you tell if your Grand Cherokee fuel pump is going out?

The only way that you are going to know that your Grand Cherokee’s fuel pump is going out is that it is no longer providing enough fuel pressure to keep the engine running under a heavy load, or at high-speed. Typically, if you are heading up a hill (or accelerating) the engine may start to feel like it is just running out of steam.

Can a Jeep Grand Cherokee Run without gas?

Without gas your Grand Cherokee will not run at all. With that in mind, most of the symptoms of a bad fuel pump revolve around the vehicle stalling out or not running at all. In modern fuel injected vehicles, the fuel pump sits right in the fuel tank and “pushes” the gasoline to the fuel rail (s).

Where to get a fuel pump for a Jeep Grand Cherokee?

Find a fuel pump replacement for Jeep Grand Cherokee at AutoZone by shopping our unbeatable line-up. Grand Cherokee fuel pumps feed fuel to the engine through a line by using pressure. Pressure changes lead to the engine jerking when you accelerate or to sputtering at high speeds.

Where does the fuel pump go in a car?

In modern fuel injected vehicles, the fuel pump sits right in the fuel tank and “pushes” the gasoline to the fuel rail (s). It is in the fuel tank because “pushing” fuel to the fuel rail is easier than “pulling” the fuel, which is what an inline pump would do.

What are the symptoms of a bad fuel pump?

Jeep Grand Cherokee Bad Fuel Pump Symptoms. 1 Whining Noise. One of the most common signs that a fuel pump is going bad is a whining sound. The whining sound can indicate that the fuel pump is 2 Sputtering Under Acceleration. 3 Challenges Starting the Engine. 4 Engine Won’t Start.

How do you remove a fuel pump from a jeep?

Remove the fuel sending unit from the Jeep and detach the fuel pump wires from the unit. Loosen the pump hose clamp at the fuel sending unit using the flat head screwdriver then detach the hose from the unit. Unscrew the top bracket nut holding the pump to the fuel sending unit then remove the fuel pump from the unit using a ratchet and socket.

How do you run a fuel pump on an electric car?

Cut the fuel lines in half, once between the fuel tank and the pump and then again from the pump to the engine. Install a universal inline fuel filter at each cut point attaching the hoses with hose clamps and making sure that the arrows on the fuel filters are pointed towards the engine.

When do you need to replace your fuel pump?

These screeches will typically precede a more serious mechanical failure, so act now to have an expert assess your vehicle. Having a mechanic replace your fuel pump can prevent further issues from happening down the road. 5. Engine Won’t Start

Can a fuel pump be replaced in a Jeep Wrangler?

Replacing the Fuel pump, in your Jeep TJ Wrangler really isn’t that hard, it’s just kind of a pain in the ass removing those clips. The Canadian Winters tend to make plastic brittle and removing the fuel line clips was not a good experience as they ended up breaking and I had to hunt around to find new ones.

How do you hook up a fuel pump to an electric tank?

Cut the wire and crimp the terminal to the end with your electrical pliers. Follow the fuel line that came from the old fuel pump back to where it connects to the feed line from the tank. Loosen the hose clamp and remove the hose. Attach the new fuel line from the tank to the electric pump with hose clamps.

How do you get gas out of a fuel pump?

Place a glass jar under the hose connections to the fuel pump and then pull the hoses off the fuel pump; catch any gas that is still in the line in the glass jar. Make sure you also disconnect the line from the fuel pump to the carburetor or fuel injection system, and remove that hose completely.

Can a fuel pump be converted to an electric?

Converting your vehicle from a mechanical fuel pump to an electric fuel pump system can help you avoid vapor lock issues, even out idle speeds and increase the torque of your engine by providing your engine with a reliable and constant fuel at an even temperature.

How big is the fuel line connector on a Jeep Grand Cherokee?

Shop AutoZone for Jeep Grand Cherokee Fuel Line Connector. Notes: Inlet. Nylon Straight. 3/8″ x 3/8″ Notes: Inlet.

How do you refill a fuel tank in a jeep?

Attach the fuel hoses to the fuel sending unit and tighten the clamps using the flat head screwdriver. Lower the Jeep with the floor jack. Refill the fuel tank. Reattach the ground battery cable (black) using the wrench then retighten the fuel filler cap. Start the engine and check for fuel leaks at the tank.

Where is the pressure test port on a Jeep Cherokee?

Detach the ground battery cable (black) using a wrench and loosen the fuel filler cap. Unscrew the cap from the pressure test port on the fuel rail. The test port is similar to the air valve on your Cherokee tires and is located on the fuel pipe leading to the fuel injectors on the top area of the engine.

What causes a fuel pump to wear out?

As your fuel pump begins to wear out, its components often wear down at different rates. When this mismatch becomes great enough, the pressure in your fuel lines can become inconsistent.

What are the symptoms of a bad fuel pump in a Jeep Grand Cherokee?

Here are the most common symptoms of a bad fuel pump in your Jeep Grand Cherokee: One of the most common signs that a fuel pump is going bad is a whining sound. The whining sound can indicate that the fuel pump is going out before there are any performance based issues.

What to do if your Jeep Cherokee stops running?

If the Jeep Cherokee has stopped running or will not start and you feel that the fuel pump has failed, then this is the proper way of diagnosing the problem before replacing an item that may not be needed. Starting from the basics, take off the fuel cap and listen closely for the fuel pump to come on as a helper turns on the ignition key.

Where does the fuel pump go in a Jeep Grand Cherokee?

1993, 1994, 1995 4.0L Jeep Grand Cherokee. Fuel pump troubleshooting notes: The fuel pump relay gets power from fuse #6 (15 Amp) of the Power Distribution Center (PDC). The PCM activates the fuel pump relay and the auto shut down (ASD) relay at the exact same time and thru’ the same circuit (PNK wire).

What is the fuel pressure on a Jeep Grand Cherokee?

If either sensor indicates no engine RPMs, the PCM will not activate the fuel pump relay past the 1-3 seconds initial run time. Key On Engine Running: 31 PSI (2.2kg/cm²). Key On Engine Off: 39-41 PSI (2.7-2.9kg/cm²). Key On Engine Running (but no vacuum applied to fuel pressure regulator): 39-41 PSI (2.7-2.9kg/cm²).

How do you siphon fuel from a jeep?

Catch the squirt of fuel with the shop towel then replace the cap on the test port. Siphon the fuel from the fuel tank into an approved container using a hand siphon pump. Lift the rear of your Jeep using a floor jack. Place a jack stand on each side for support and lower the vehicle.

Where is the fuel injection connector on a Jeep Grand Cherokee?

1993, 1994, 1995 Jeep Grand Cherokee 60 Pin Connector (4.0L) The fuel injection computer (known in tech speak as the PCM = Powertrain Control Module) is located on the firewall (passenger side) of your Jeep Grand Cherokee.

What are the pins on a 1993 Jeep Grand Cherokee?

1993, 1994, 1995 4.0L Grand Cherokee 60 Pin Connector Pin Wire Color Description 1 RED/WHT MAP Sensor Signal 2 TAN/BLK ECT Sensor 3 PNK/BLK RED Battery Power ( 1993 Only) Battery Power 4 BLK/LT BLU Sensor Ground

How do you connect a fuel pump to a fuel tank?

Attach the fuel pump wires to the unit. Place a new O-ring seal on the fuel tank opening. Install the fuel sending unit in the tank and rotate the retaining locking ring clockwise with the brass punch and hammer until the ring hits the stops. Plug the wiring harness electrical connector to the fuel sending unit.

Do you need to lower tank to replace fuel pump?

However, you do not need to lower the tank to replace a failed pump, which makes it relatively easy to replace. Still, you want to make sure the O-ring under the sending unit assembly, which contains the fuel pump, seals properly.

How do you remove a fuel pump from a fuel sending unit?

Loosen the pump hose clamp at the fuel sending unit using the flat head screwdriver then detach the hose from the unit. Unscrew the top bracket nut holding the pump to the fuel sending unit then remove the fuel pump from the unit using a ratchet and socket.

Where can I buy a fuel pump kit?

Images depict actual item and necessary components *** This Complete Fuel Pump Kit contains the Module, Sending Unit and all necessary components – all built according to the highest standards of quality and precise specifications. These items are shipped from and sold by different sellers.

What kind of fuel pump does a GMC k1500 have?

Had to do the job twice so not very happy about that, waste of my Sunday. This was a exact fit for my 92 GMC K1500 with a 5.7L VIN K motor. It fixed my low power, runs rough and start / stall issue.

Navigation