Can a Jeep Laredo go forward or reverse?

Can a Jeep Laredo go forward or reverse?

I am having a bit of a situation. I have a 2002 Jeep Grand Cherokee Laredo. Yesterday it was running forward and reverse with no problems. Well this morning as I do every morning, I started it, let it warm up for about 30 seconds or so, when i shift to reverse, guess what….wont go reverse.

What happens if your Jeep Grand Cherokee is stuck in Park?

The shift linkage on your Grand Cherokee will usually provide a lifetime of dependable service. But, they can go bad. If you are positive that the gear shifter is not stuck in park (see directly above), then it’s likely that the shift linkage may be bad.

What kind of transmission does a Jeep Laredo have?

I have a 2002 Jeep Grand Cherokee Laredo. Yesterday it was running forward and reverse with no problems. Well this morning as I do every morning, I started it, let it warm up for about 30 seconds or so, when i shift to reverse, guess what….wont go reverse. I have no tranny light on.

Why is my Jeep Grand Cherokee not shifting?

Matthew Wright has been a freelance writer and editor for over 10 years and an automotive repair professional for three decades specializing in European vintage vehicles. There is a common issue with shifting on a number of Jeep Grand Cherokee models as they age and their mileage increases.

The shift linkage on your Grand Cherokee will usually provide a lifetime of dependable service. But, they can go bad. If you are positive that the gear shifter is not stuck in park (see directly above), then it’s likely that the shift linkage may be bad.

Matthew Wright has been a freelance writer and editor for over 10 years and an automotive repair professional for three decades specializing in European vintage vehicles. There is a common issue with shifting on a number of Jeep Grand Cherokee models as they age and their mileage increases.

What happens when the Jeep Grand Cherokee is in overdrive?

If the transmission fluid temperature sensor reports an overheating condition (over 260 degrees F) and the transmission is currently in overdrive, the TCM will downshift to third gear. The TCM will also light the LED in the dash-mounted OD off switch until the temperature drops below 230 degrees F.

When did Jeep start using The 42RE transmission?

Jeep Grand Cherokee started using the 42RE transmission in 1993 1/2 models with the 4.0L engine. The “4” stands for 4-speed, “2” is for torque capacity, “R” is for rear-wheel drive, and “E” is for electronically controlled.

What to do when your Jeep won’t move out of Park?

Seconds later my gal jumps in the driver seat and the Jeep won’t move out of park. I discover that if I take off the shift cover (cover that reads P R N D 2 1), I can still push the pin downward and I am able to shift into gear (with foot on the break and pushing in the shift button on the shift handle T-grip).

What causes a Jeep Wrangler to get stuck in Park?

Knows a couple things… It is very likely nothing serious, the usual cause for that issue is a broken plastic push rod that is inside the vertical part of the shifter itself. The top button pushes a cam sideways that pushes down on the plastic shift rod that unlocks the shifter.

How do you change the transmission on a Jeep Wrangler?

The top button pushes a cam sideways that pushes down on the plastic shift rod that unlocks the shifter. The shift rod is easily replaced. The ‘T’ top of the shifter is removed by pulling HARD straight up on it.

Why is my 4WD not working on my Jeep Wrangler?

They could be any of the following but not limited to: These are some of the most common reasons why your Jeep could fail to engage the 4WD system. The symptoms will differ somewhat between them, for example, the 4WD light will flash on the dash but never actually engage, or the 4WD light will shine solid, but you have no active 4WD engaged.

How to disconnect 4 wheel drive Jeep Wrangler?

Locate the four nozzles on the vacuum switch that control your front disconnect system for your 4wheel drive. (Located on top of your transfer case) Locate the red line (constant source) coming from the transfer case and connect it to the original red hose running behind your air cleaner.

Why is my Jeep Wrangler not engaging 4H?

If the lever feels more loose than normal or when you shift the lever back the Jeep fails to engage 4H or 4Lo. If this happens then you need to investigate immediately by crawling underneath the Jeep and have a look at this transfer case linkage.

How to get a Jeep Wrangler 4WD to engage?

1 Ensure no acceleration on the throttle 2 Select 4H or 4Lo to engage the transfer case 3 Press the button and give the cable a one-inch pull into a fully engaged position 4 Release the button once 4WD is engaged.

Why does my Jeep clunk when I put it in reverse?

Ok, one more note: the clunking sound is coming from the pinion/rear diff. Jeep got a 2.5” lift a couple weeks ago and now has 33” MTs. Any adjustment to the angle/pinion depth required? I guess I’m still not sure why it only clunks when going into reverse. Oh, and one more! Haha. Noise goes away when I put it in 4wd.

What kind of lift does a WRANGLER JK have?

Discussion in ‘ Wrangler JK (2007-2017) ‘ started by Jeepwilli, Jun 6, 2019 . I’m new to the forum, but very happy to be here. I tried the search function, but can’t find the answer to my question. I hope this is the right forum. If not, my apologies! 2007 JK automatic 2.5” lift. No other major mods.

What happens when you put a jeep in reverse?

Reverse worked a couple more times. After about five minutes of driving, it died in revese again. I tried to experiment with it.

What happens when I put the car in reverse?

Put the car in reverse holding the brake the car stalls, if I go into neutral or drive it works fine. If I put the car in reverse not holding the brake it shifts rough but doesn’t stall. I have not driven the car at speeds higher than 35mph, so not sure of the other gears.

Ok, one more note: the clunking sound is coming from the pinion/rear diff. Jeep got a 2.5” lift a couple weeks ago and now has 33” MTs. Any adjustment to the angle/pinion depth required? I guess I’m still not sure why it only clunks when going into reverse. Oh, and one more! Haha. Noise goes away when I put it in 4wd.

Discussion in ‘ Wrangler JK (2007-2017) ‘ started by Jeepwilli, Jun 6, 2019 . I’m new to the forum, but very happy to be here. I tried the search function, but can’t find the answer to my question. I hope this is the right forum. If not, my apologies! 2007 JK automatic 2.5” lift. No other major mods.

Can a Jeep Grand Cherokee have a reverse?

2004 grand cherokee, automatice, all forward gears work fine, no reverse. Check your transmission fluid level. Make sure its full and red like cherry kool-aid. If its low fill to the proper level. If its brown/black and smells burnt you might get lucky and save the transmission with a transmission flush.

I am having a bit of a situation. I have a 2002 Jeep Grand Cherokee Laredo. Yesterday it was running forward and reverse with no problems. Well this morning as I do every morning, I started it, let it warm up for about 30 seconds or so, when i shift to reverse, guess what….wont go reverse.

2004 grand cherokee, automatice, all forward gears work fine, no reverse. Check your transmission fluid level. Make sure its full and red like cherry kool-aid. If its low fill to the proper level. If its brown/black and smells burnt you might get lucky and save the transmission with a transmission flush.

I have a 2002 Jeep Grand Cherokee Laredo. Yesterday it was running forward and reverse with no problems. Well this morning as I do every morning, I started it, let it warm up for about 30 seconds or so, when i shift to reverse, guess what….wont go reverse. I have no tranny light on.

Why does my Jeep Grand Cherokee turn on auto park?

If you open a door while it Is in Drive or reverse, it will change to ‘Park. 42 people found this helpful. Can you shut that feature off? 33 people found this helpful.

What should the reverse light wire be on a jeep?

Nobody knows? should be white/Lt green @ the Integrated poweer module. Should be the same color @ the light itself, i’d just go there. If you go to Just4jeeps.com and find the factory back-up cam instructions it shows you what color and where to find it.

What happens when reverse goes out in a jeep?

Jeep Grand Cherokee Questions – reverse went out without any warning, all other gears work perfectly f… – CarGurus reverse went out without any warning, all other gears work perfectly fine. i can feel it shift into reverse but no movement at all. 2004 grand cherokee, automatice, all forward gears work fine, no reverse.

When did the Jeep Grand Cherokee ZJ come out?

In this article, we consider the first-generation Jeep Grand Cherokee (ZJ) after a facelift, produced from 1996 to 1998. Here you will find fuse box diagrams of Jeep Grand Cherokee 1996, 1997 and 1998, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

Why are the turn signals on my Jeep not working?

Jeep Turn Signals not Working? Here is a quick fix. – YouTube Jeep Turn Signals not Working? Here is a quick fix. If playback doesn’t begin shortly, try restarting your device.

What to do if your Jeep Wrangler is stalling?

You ignore a bad OPDA at your own peril, since failure to replace this relatively inexpensive component will result in lack of sufficient lubrication and eventually catastrophic engine failure. The repair is a DIY repair for any hands-on type of person without the need for any special tools.

Can a Jeep Grand Cherokee Drive in two gears?

You’re often still able to drive the vehicle, but it only operates in one or two gears. For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually.

Why does my Jeep Grand Cherokee not shift gears?

For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually. The most common cause of transmission problems is the easiest to fix: check the fluid level in the transmission and restore it to the proper levels.

You’re often still able to drive the vehicle, but it only operates in one or two gears. For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually.

For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually. The most common cause of transmission problems is the easiest to fix: check the fluid level in the transmission and restore it to the proper levels.

Why does my car not move in drive but will in reverse?

One such vexing issue is car wont move in drive but will in reverse. Why Does The Car Wont Move In Drive But Will In Reverse? Transmissions, especially, the automatic transmission only goes in reverse in the event of the failure or damage of a component in the system. It could also be a fault with the speed sensor.

Why is my reverse camera not working on my Jeep Laredo?

I had the same issue with my MY2014 Grand Cherokee Laredo. The reverse camera simple stopped working and problem coincided with me blowing the 20A cigarette lighter fuse (Fuse F93 in the fuse panel under the bonnet/hood/engine bay) when using the cigarette lighter to run a 12V to 240V inverter to charge my laptop battery.

Why is my back up camera not working on my Jeep?

But they said they couldent re-flash the computer because the tipm now ive read about the tipm problems with my year jeep (2011 jgc limited) now i have not had any problems with the tipm besides this. Now if you guys could please give me your advice i would greatly appreciate it alot.

What to do when your car won’t go in reverse?

Pump the clutch a few times if your car has a manual transmission system. You can also try to partially release the clutch while shifting into reverse. If the transmission doesn’t engage, switch off your car’s engine, then shift into First, then Neutral.

Why is my Jeep Wrangler not shifting gears?

Transmission Problems and Shifting Linkage ProblemsThe two causes of shifting problems most likely to be found in a Jeep Wrangler are related to the shift linkage and the transmission.

Why is it having trouble moving in reverse?

So when forward and reverse are selected at the same time the transmission binds and the car ends up going nowhere fast. The more revs you give it the worse it gets. They replaced the main shaft and now the problem is gone. Read more at http://www.honda-tech.com/showthread.php…

Why does my Jeep Grand Cherokee have no traction?

I was driving in forward then reverse to make a path in the snow when I heard a loud “clunk”. My tires spun after that. The Jeep drives fine except that it is all over the place with no traction. Obviously, my 4 wheel drive is out.

When to replace front diff on Jeep Grand Cherokee?

Dealer replaced the front diff. under warranty. Exactly 12 months and 10,000 miles later, in year 2 the same exact thing happened again, only this time it didn’t completely lock up right away and I was able to get off the road.

Why is my Jeep Grand Cherokee AWD not working?

The Jeep drives fine except that it is all over the place with no traction. Obviously, my 4 wheel drive is out. My Jeep is AWD and you would never even notice anything was wrong except in the inclimate Ohio weather we are having right now. I was told by a friend that my transfer case needs replaced.

Is there a problem with my Jeep Grand Cherokee?

Very often, this will solve the problem. But Jeep Grand Cherokees seem especially prone to more serious transmission problems, and some owners are quite vexed at their inability to determine the causes.

Where was the Jeep Cherokee that shifted into neutral?

While approaching a stop, the vehicle inadvertently shifted into neutral. The failure occurred intermittently and without warning. The vehicle was taken to monroeville Chrysler Jeep 3 (651 william penn hwy, monroeville, PA 15146, (412) 856-1422) where the transfer case was repaired twice and the motor as well.

What was the worst problem with a 2001 Jeep Grand Cherokee?

Worst 2001 Jeep Grand Cherokee Problems #1: Knocking Noise, Cracked Piston 2001 Grand Cherokee Average Cost to Fix: $4,000 #2: Gauges Don’t Work 2001 Grand Cherokee Average Cost to Fix: $3,000 #3: Power Window Stopped Working 2001 Grand Cherokee Average Cost to Fix: $200

Worst 2001 Jeep Grand Cherokee Problems #1: Knocking Noise, Cracked Piston 2001 Grand Cherokee Average Cost to Fix: $4,000 #2: Gauges Don’t Work 2001 Grand Cherokee Average Cost to Fix: $3,000 #3: Power Window Stopped Working 2001 Grand Cherokee Average Cost to Fix: $200

Where can I Donate my 2001 Jeep Grand Cherokee?

Donate your old car in minutes through the CarTalk Vehicle Donation Program. Click on a category below for details. Help? Loading Curious how the 2001 Grand Cherokee compares to other years?

Why does my car reverse but not go forward?

The gear cable could be stretched further than the normal length and requires adjusting. The failure of some internal components can be the cause too. The car will reverse but not go forward because of worn out solenoids, clutches, or gears.

What causes a manual transmission to not move?

Now its time to talk about why a manual transmission won’t move. The number one cause is the clutch components have worn out and no longer have enough friction material to overcome the weight of the vehicle. A second possibility is the transmission can be stuck in two gears at the same time and it won’t move.

What to do if your transmission is unresponsive?

Your symptoms are pointing to an unresponsive transmission. When the transmission fails to respond, the first thing to do is check the level of the transmission fluid. If it is low, then there is a leak, and possibly further engine damage.

Why is my Jeep Grand Cherokee shifting funny?

The automatic transmission in my wife’s 2002 Jeep Grand Cherokee began shifting “funny” one day while in traffic. The next morning when she went to pull out of our driveway she thought the transmission felt like it was slipping. That night when she returned from work I took it for a test drive. I backed out the driveway in reverse with no problems.

How is the transmission sensor on a Jeep Grand Cherokee held down?

Notice in the picture and in your transmission that the plate holding down the governor pressure solenoid and sensor is held on by only three 7/16 bolts and two Torx screws. This is TOO EASY! Remove the bolts and screws. Place your hand under the SOLENOID so it doesn’t drop and evenly pull down on the holding plate.

What happens when the reverse goes out in a Jeep Grand Cherokee?

reverse went out without any warning, all other gears work perfectly fine. i can feel it shift into reverse but no movement at all. 2004 grand cherokee, automatice, all forward gears work fine, no reverse. Check your transmission fluid level. Make sure its full and red like cherry kool-aid. If its low fill to the proper level.

How to change reverse light on Jeep Grand Cherokee?

The reverse light gets dimmer over time and we suggest changing them in pairs. Try not to touch the glass part of the new bulb with your finger when changing the reverse light in your Grand Cherokee, the oil in your finger will cause the that part of the reverse light bulb to burn hotter out therefore burn out quicker.

Where was the 2004 Jeep Grand Cherokee Laredo purchased?

Mileage: 130,446 miles Body Type: SUV Color: Silver Engine: 6 Cyl 4.0 L No accident or damage reported to CARFAX. Purchased on 04/01/03 and owned in TX until 04/21/21. Driven an estimated 10,687 miles/year. Last serviced in Dallas, TX on 03/12/21 • Vehicle serviced • Emission system checked • Emissions or safety inspection performed.

reverse went out without any warning, all other gears work perfectly fine. i can feel it shift into reverse but no movement at all. 2004 grand cherokee, automatice, all forward gears work fine, no reverse. Check your transmission fluid level. Make sure its full and red like cherry kool-aid. If its low fill to the proper level.

Very often, this will solve the problem. But Jeep Grand Cherokees seem especially prone to more serious transmission problems, and some owners are quite vexed at their inability to determine the causes.

What makes a Jeep Grand Cherokee stay in Park?

The shift lock solenoid is the mechanism that keeps you from shifting out of park without your foot on the brake. The good news is that most shift locks have an override button. You will need to find it for your particular model year of Grand Cherokee (if applicable). Finding it is usually pretty easy.

Are there any problems with the Jeep Cherokee?

Although it is one of the most recognizable models on the SUV landscape, the Jeep Cherokee has been plagued through the years by driver complaints about chronic stalling. There are countless instances of Jeep Cherokees stalling while traveling at low speeds or high speeds, driving straight or losing power in the midst of a turn.

What should I do about my Jeep Cherokee stalling?

A deep dive into actual solutions offered by the most trusted sources, fellow Jeep Cherokee owners like you.

What does the PCM do on a Jeep Cherokee?

The PCM (Powertrain Control Module) is a computerized system that monitors and controls various systems on a Jeep Cherokee, including vital operations such as engine timing, the transmission (gear shifting), anti-lock braking, fuel to air ratio mixing and quite a few others.

What makes the Jeep Grand Cherokee L Special?

A LEGACY EXTENDED 1 EXTRAORDINARY CAPABILITY. Highly versatile, the Grand Cherokee L offers three available 4×4 systems and a host of capability features designed for off-road trails, city streets and everything in between. 2 EXPANSIVE INTERIOR. 3 THE PEAK OF TECHNOLOGY.

How many trims does the Jeep Grand Cherokee L have?

The All-New Grand Cherokee L comes in four trims that are ready for any day trip or daily routine.

What’s the towing capacity of a Jeep Grand Cherokee?

The highly versatile Grand Cherokee L offers three available 4×4 systems and a host of capability features designed for off-road trails, city streets and everything in between. Available all-weather capability and a Best-in-Class Maximum Towing Capacity of 7,200 pounds continue to advance the legendary reputation of Grand Cherokee.

What happens when you reset the transmission shift points?

It is not going to make your shifting abnormal. If your gear shifts are abnormal you have something else going on. Resetting the transmission shift points makes the transmission the same as when the car is out of the factory. Within 30 driving cycles, the ECU will monitor your driving habits and adapt the shifting points to your driving style.

Can a bad throttle position sensor cause idle surging?

Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. 3) Check Engine Light

Why does my Jeep Cherokee stall while driving?

A significant number of drivers have reported that not only did their Jeep Cherokees lose engine power while driving, but in nearly all cases, stalling occurred without any warning and with no indicator lights on the instrument panel.

How is the 2004 Jeep Grand Cherokee Laredo?

2004 Jeep Grand Cherokee Laredo We love our 2004 jeep grand Cherokee Laredo. Have 110,400 miles to date. Bought it new. One outstanding feature is the music system – great speaker quality. The car is extremely comfortable to drive and ride in. It has been quite maintenance free, as we have been faithful about servicing every three thousand miles.

Why does my Jeep Grand Cherokee not turn?

If you’ve broken a drive/axle shaft, your Jeep Grand Cherokee’s transmission has no way to turn the wheels anymore. If this were the case, there would not be any movement whatsoever from the vehicle. You also wouldn’t feel the slight jerk your Grand Cherokee as you put it into gear. 4. Bad Transmission

What did Edmunds say about the 2004 Jeep Grand Cherokee?

Edmunds’ expert review of the Used 2004 Jeep Grand Cherokee provides the latest look at trim-level features and specs, performance, safety, and comfort. At Edmunds we drive every car we review, performing road tests and competitor comparisons to help you find your perfect car.

What are the repairs on a 2004 Jeep Grand Cherokee?

Only major repairs is a transmission solenoid about 450 at 160k miles, fuel pump at 90k miles (ran the gas too low for a long period of time my own fault). Other than that change all fluids when your supposed to and has been a good reliable vehicle for me. I purchased my Rocky Mountain Edition as a dealer demo.

What are the trim levels of the 2004 Jeep Grand Cherokee?

2004 Jeep Grand Cherokee models The Grand Cherokee now comes in six trim levels: Laredo, Limited, Freedom Edition, Special Edition, Overland and Columbia Edition.

What’s the price of a 2004 Jeep Laredo?

MSRPs range from $26,980 for a six-cylinder 2WD Laredo to $38,995 for a 4WD Overland with a V8. Rebates of $3,000 and zero-percent financing can sweeten the deal. But there’s no question that this is a dated product.

Reverse worked a couple more times. After about five minutes of driving, it died in revese again. I tried to experiment with it.

Why does my car drive in reverse but not forward?

The car continued to drive fine but the remote starter would not function. The check engine light went out (remote starter now works) and 2 days later the car would not drive in forward gear. The gear shift will go into all the positions, but the only gear that will engage is the Reverse gear.

Where is the neutral switch on an automatic transmission?

The neutral safety switch for an automatic transmission is located inside the transmission case or in the linkage that allows the vehicle to shift gears. This switch prevents you from starting the engine when the transmission is in any gear other than Park or Neutral.

What happens if you hit the neutral switch?

This component is the neutral safety switch. For instance, if you inadvertently set the gear to Drive and then try to start the engine, the neutral safety switch will prevent the engine from starting. That way, the vehicle will not roll forward right afterward.

Why does my Jeep Grand Cherokee not shift into overdrive?

BTW: it’s a 95 4.0l grand cherokee w/130k on it. if u have a push button on dash for overdrive c if it works? borg warner has alot of overdrive problems with 42re and 44re overdrives check ur wiring out on transmission does it happen all the time or maybe when trans is cold or hot?

Where does the torque converter lock up in a jeep?

In the 1-2 position, the torque converter can lock up in first or second gear. In 3 or D it will only lock in 3 or four. The normal sequence is to shift to second, and then third, then forth and then the torque converter will lock up giving an engine speed of about 2700 RPM at 55 MPH.

How does the torque converter work on a jeep AW4?

Normally, the transmission with switch to 2nd at 20 to 25 mph depending on the TPS signal. It gets its speed reference from the internal speed sensor so if you are in low range, the speed will be different. In the 1-2 position, the torque converter can lock up in first or second gear. In 3 or D it will only lock in 3 or four.

The neutral safety switch for an automatic transmission is located inside the transmission case or in the linkage that allows the vehicle to shift gears. This switch prevents you from starting the engine when the transmission is in any gear other than Park or Neutral.

What causes gears to chatter in Jeep Liberty?

Insufficient gear oil due to a leak can cause the gears to chatter. Check the transmission oil seal or vehicle speed sensor O-ring. Drive the vehicle and check for gear slippage, noise or no drive in forward or reverse gears. Lack of automatic transmission fluid can cause these issues.

How to troubleshoot a Jeep Liberty’s transmission?

The main drive gear bearing or countershaft also may be damaged. Check for noise in a particular gear. This indicates worn, damaged or chipped gear teeth. The synchronizer for the gear may also be worn or damaged. Drive the vehicle and check for slippage in high gears.

Is the solenoid on a Jeep Liberty defective?

If the gear shift button can depress, the solenoid is defective. Chris Orr began his career in 1988 as a sports writer. His work has appeared in “USD Vista,” “UNLV Rebel Yell” and the “East Honolulu Newspaper” among other publications.

Is there a problem with the Jeep Liberty transmission?

Well now when I slow to a stop there is a jerking feeling. It happens at 30 mph. Does anyone else have this problem? Hi Dean12…Well as an update I took it to the dealer and I told them of my issue and they plugged my car into the computer and recalibrated the transmission. So far no problem but I am not holding my breath.

How can I pull out of a Jeep Liberty?

When you engage 4WD/Part-time the front wheel on the passenger’s side is the only one that can help you pull out. There is no limited slip on the front differential, so the front wheel driver’s side is “floating”. Just keep in mind the transfer case can lock the front right and the rear left wheels if you don’t have Trac-Loc.

Insufficient gear oil due to a leak can cause the gears to chatter. Check the transmission oil seal or vehicle speed sensor O-ring. Drive the vehicle and check for gear slippage, noise or no drive in forward or reverse gears. Lack of automatic transmission fluid can cause these issues.

Why are the reverse lights not working on my Jeep Grand Cherokee?

The reverse lights are a known problem on this generation of Jeep Grand Cherokee. 99-2003. The factory switch that activates the reverse lights is part of the valve body inside the transmission. When it fails typically the only problem is the lights not working, so I was not about to pay the $400+ for the valve body and open up the tranny.

Nobody knows? should be white/Lt green @ the Integrated poweer module. Should be the same color @ the light itself, i’d just go there. If you go to Just4jeeps.com and find the factory back-up cam instructions it shows you what color and where to find it.

What kind of acceleration does a Jeep Cherokee have?

Jeep Cherokee: starts fine..pedal..it wont accelerate past 30 or rev… 2008 jeep grand cherokee laredo. just changed rear end. Howl is gone but can’t accelerate over 38 mph with gas pedal floored. check engine light … read more Grand Cherokee: I have a 1999 Grand Cherokee Limited.

What’s the gear shift on a Jeep Cherokee chief?

Hello, Shifting into first (and then into second) gear on my manual transmission ’96 Cherokee Chief has suddenly become extremely difficult. I’ll try to force the gear shift, and sometimes that will w … read more

Why does my Jeep Rev when I Shift?

Jeep revving, hesitating, and jerking jeep transmissions I have a Jeep Grand Cherokee Laredo with over 107,000 miles. A few weeks ago it revved up once when I shifted into drive. I thought maybe my foot had hit the gas pedal accidentally, so I thought nothing of it.

BTW: it’s a 95 4.0l grand cherokee w/130k on it. if u have a push button on dash for overdrive c if it works? borg warner has alot of overdrive problems with 42re and 44re overdrives check ur wiring out on transmission does it happen all the time or maybe when trans is cold or hot?

What are the problems with the 2005 Jeep Wrangler?

See all problems of the 2005 Jeep Wrangler . Jeep started stalling either when parked or in traffic. Dealership says its the powertrain control unit (pcm or computer). Twice engine stalled as I was driving.

What causes a Jeep Wrangler to pop out of gear?

Manual transmission sometimes pops violently out of gear when shifting to 3rd. Dealership test drove but didn’t experience the problem. Manual transmission violently pops out of gear when shifting to 3rd gear. Does not affect any other gear. Chrysler said to give it “sufficient follow through” when shifting into 3rd gear.

What was the problem with the Jeep Wrangler transmission?

Diagnosis by dealer indicated Transmission needed to be repaired, so they put in a new one under warranty. Clutch made noise when engaged which was only noticeable when engine was off. Throwout bearing replaced. Rear axle seals leaking. Passenger rear axle seal was leaking after off-road trip.