How to disassemble a Jeep Grand Cherokee dashboard?

Remove the final retainer bolt positioned on top of the brake pedal in a similar fashion.Slide the dash towards you and disconnect the electrical connectors going into the back side of the dash. Drag the dash up and carry it out of your Jeep. “Jeep Grand Cherokee 1993 thru 2004: All Models; Haynes Repair Manual”; John Haynes; 2004

How do you install speakers on a Jeep Cherokee?

Installing a new set of speakers that have been designed specifically for your Jeep is easy too, thanks to factory style plugs and mounting brackets.

How do you remove radio from Jeep Cherokee?

Identify the two retainer screws for the radio panel. There is one screw on each side of the radio. Remove these screws with the Phillip’s head screwdriver and slide the panel forward. Unplug the radio’s electrical connectors. Drag the heater control assembly forward.

How do you hook up a stereo to a jeep?

Hold the receiver assembly near the dash and connect the Crutchfield adapter harness to the factory harness, then plug the antenna lead into the rear of the receiver and slide the entire assembly into the dash cavity. Secure it with the two 3/8” screws you removed earlier, then test the receiver to make sure everything’s working properly.

Installing a new set of speakers that have been designed specifically for your Jeep is easy too, thanks to factory style plugs and mounting brackets.

Can a quadratec subwoofer be replaced in a jeep?

We stock hard to find replacement speakers that you can only get from Quadratec, like the factory subwoofer found in the 01-06 Wrangler, in addition to speaker pairs and all the way up to complete audio system overhaul kits that include every speaker you need for your Jeep. Some kits even include additional amplifiers and subwoofers!

Where do you change the lights on a Jeep Cherokee?

The instrument panel lights on your Jeep Cherokee are small, low-wattage bulbs that illuminate the instrument panel from behind. Occasionally these lights burn out and must be replaced. You will typically purchase replacement lights from a Chrysler dealership, although some auto parts stores may carry the correct size bulbs you need.

How do you change the instrument panel on a Jeep Cherokee?

Use the screwdriver to twist out the two screws on the underside of the Cherokee’s cowl on the instrument panel. Pull the cowl forward by hand, and remove the cowl trim. Remove the four screws holding the instrument panel in place. Slide the instrument panel forward.

What to do if your dashboard light goes off?

The dimmer switch may have been pressed by accident or adjusted by another driver of the vehicle causing the dashboard lights to become dull or switched off. Step 1: Locate the dimmer switch. Step 2: Adjust the dimmer switch. Step 1: Locate the fuse for the dashboard lights. Step 2: Remove and inspect the fuse. Step 3: Replace damaged fuses.

How do you remove a heat lamp from a jeep?

Using a flat screwdriver unclip the clamshell plastic housing and then remove the control board. You will see the three burned out lamps on the face of the board, using a pair of pliers grab them at the plastic base and gently twist, they come off very easy.

How do you change the battery on a Jeep Cherokee?

Open the hood of the Jeep Cherokee, and disconnect the negative battery cable. Loosen the nut on the cable clamp, using a socket wrench, and slide the clamp off the negative terminal. Use the screwdriver to twist out the two screws on the underside of the Cherokee’s cowl on the instrument panel.

What makes up the dashboard of a jeep?

The dashboard is composed of many pieces including the gauges of the instrument cluster and the surrounding panel, the defroster vent cover and radio panel, along with the panel that surrounds the heater controls. Park your Jeep and apply the parking brake.

How do you remove kick panels from Jeep?

Remove the retainer screws for the kick panels and pull the kick panels straight out. Pry off the trim pieces going around the glove box using the flathead screwdriver to reveal the retainer bolts. Remove these bolts with the socket wrench. Locate the retainer bolts on the ends of the dash panel and remove them with the socket wrench.

Where are the fuses on a 2003 Jeep Grand Cherokee?

2003 Jeep Grand Cherokee Fuse Diagrams for Junction Box in cabin and Power Distribution Center under hood 10. Radiator fan relay 40A Alldatadiy.com and Eautorepair.net are professional-grade shop manuals—period. They include wiring diagrams and technical service bulletins.

Which is Jeep has the best wiring diagram?

Jeep Grand Cherokee LaredoJeep Grand Cherokee PartsJeep Cherokee SportCherokee FoodCherokee TribeRadiosJeep Wrangler EngineTrailer Wiring DiagramCherokee Language Repair Guides Within 98 Jeep Cherokee Wiring Diagram In 2004 Grand | Best Diagram Collection

How to remove a battery from a Jeep Grand Cherokee?

Connect a test light or a voltmeter across the terminals of the fuse. 3. Starting at the fuse block, wiggle the wiring harness about 6 – 8 inches apart and watch the voltmeter/test lamp. fPage 324 Terminal Removing Tool 6934 fPage 221 Control Module HVAC: Service and Repair REMOVAL 1. Disconnect and isolate the battery negative cable. 2.

Do you need to remove the dashboard on a Jeep Cherokee?

You may decide to remove the dashboard on your Jeep Cherokee for several reasons. Whether you are replacing one of the components of the instrument cluster or you need to repair your heating system; you will have to get the dashboard out of the way before you begin.

How do you disassemble a Jeep Cherokee?

Unbolt the top portion of the dash with the socket wrench. Unscrew and the defroster vent cover then undo the retaining clips manually. Remove the cover and the weather stripping by pulling it straight off. Insert the flathead screwdriver under the panels at the bottom of the dash by the doors. Pull down on the screwdriver to pry the panels off.

How do you remove battery from Jeep Cherokee?

Prop your hood open and detach the black negative battery cable from its port on the battery with the socket wrench. Open your front doors. Remove the four retainer screws from the base of the instrument cluster panel with the Phillip’s head screwdriver.

Is there a problem with my Jeep dashboard?

The company is not aware of any reported injuries related to wrinkled dashboards. As with all out-of-warranty customer claims, FCA reviews each case on an individual basis with the goal of satisfying our customer. So FCA won’t cover the problem because it’s out of warranty.

When does a jeep dashboard start getting wrinkles?

At first, it’s a striking upgrade. But given time the only thing that’s striking about the dash is how it becomes more wrinkled than Peepaw’s skin. Problems start bubbling up between 45,000 and 60,000 miles, just out of the warranty period.

How do you remove the dash from a Jeep Cherokee?

Locate the retainer bolts on the ends of the dash panel and remove them with the socket wrench. Remove the final retainer bolt positioned on top of the brake pedal in a similar fashion.Slide the dash towards you and disconnect the electrical connectors going into the back side of the dash. Drag the dash up and carry it out of your Jeep.

How to remove the front axle on a Jeep Cherokee?

Locate the lower mounting bolts for the front shock absorbers on the axle near the base of the coil springs. Remove the bolts with a wrench and leave the shocks sitting in place. The upper mounts will retain them to the body when the axle is removed. Locate and remove the banjo screw that attaches the brake calipers to the rubber brake hose.

Where are the shock absorbers located on a Jeep Cherokee?

Locate and remove the four retaining bolts where the front drive shaft meets the axle. Use a 10 mm wrench to loosen the bolts and slide the shaft out of the axle yoke, setting it out of the way. Locate the lower mounting bolts for the front shock absorbers on the axle near the base of the coil springs.

How to remove automatic transmission from Jeep Cherokee?

Push the transmission over to the passenger side until the transfer case linkage comes free which will cause the whole unit to drop even farther. Disconnect electrical connections, breather lines, sensors, and shift linkages from the top of the transmission.

How do you change the stereo in a Jeep Grand Cherokee?

Use a panel tool to pry around the edges of the stereo trim panel and release four retaining clips. Next, remove the four Phillips screws securing the radio to the dash. Pull out the stereo and disconnect the wiring harness and antenna cable. That’s all there is to it.

What does the Dashboard Light mean on a Jeep Grand Cherokee?

This Dashboard sign illuminates on your Jeep Grand Cherokee to specify that the engine oil pressure may get a leak in your Cherokee. So we recommend you to inspect your car at the Cherokee service centre. This dashboard light blinks on your Jeep Grand Cherokee dashboard to indicate that you may not close the hood of your Jeep.

What’s the problem with my 2011 Jeep Laredo?

My wife just recently began experiencing an issue with her 2011 Jeep Grand Cherokee Laredo. She will have the blower motor running and it will just quit, then cycle back on again maybe a moment or two later. Sometimes the motor will quit running for up to a minute.

What should I do about my Jeep Grand Cherokee?

The jeep has caused us a lot of heart ache over the years with random repairs and we trying not to get rid of it since it’s paid for (don’t want another car payment). So any help and advise would be great. In the meantime, I will look into Passenger Side Blend Door that was linked.

Is there a problem with the Grand Cherokee dashboard?

Surging Complaints on CarComplaints.com ∞ Model Year Problem Grand Cherokee 2011 Leather dashboard is bubbling / wrinklin 2012 Leather dashboard has delaminated 2013 Leather dashboard melting, wrinkling 2014 Leather bubbling on dashboard

Why is the leather on my Jeep dashboard Bubbling?

Leather dash started bubbling 2 years after purchasing new, dealer would not do anything because it was not severe enough and I was told the same thing by two different Jeep dealers several times over the next couple years. It continued to get worse and is now beginning to cause air flow issues with defroster.

What’s the warranty on a new Jeep dashboard?

Per this bulletin, they can replace the dashboard (leather and upper carrier) under warranty after inspecting it. Here’s the catch………… The warranty coverage is good for 6 months from the date that the bulletin is issued.

Why is the instrument cluster on my Jeep Cherokee not working?

The cluster has stopped working again too. I decided to hook my OBD2 scanner up figuring there was probably a code and I pulled the following: P1686, P1694, P1698. All of them have to do with the PCM not communicating with the instrument cluster.

Is there a problem with my Jeep Grand Cherokee?

The Jeep factory Engineers have been consulted and are aware of the problem. About the only thing that has not been replaced is the full wiring harness. The Electrical Technician is factory trained and has tried his best and also followed Jeep’s guidance.

How to get a Jeep Grand Cherokee case number assigned?

Parallel approach recommendation: Call the Jeep Customer Care 800 number and get a Case Number assigned. Write a comprehensive letter detailing service dates, mileage, and compoents replaced and how much you paid.

What are the fuse diagrams for a 2001 Jeep Grand Cherokee?

2001 Jeep Grand Cherokee Fuse Diagrams for Junction Box in cabin and Power Distribution Center under hood Alldatadiy.com and Eautorepair.net are professional-grade shop manuals—period. They include wiring diagrams and technical service bulletins.

What to do if your Jeep Grand Cherokee has electrical problems?

THE AUTO ELECTRICIAN JUST RESET THE POWER TO THE SWITCH FOR THE ELECTRIC WINDOWS. THIS HAS THEN RESET THE COMPUTER AND IT IS ALL WORKING NOW. CHECK ALL YOUR WIRES TO MAKE SURE YOU DONT HAVE A LOOSES CONNECTION. I have a 2006 Jeep Grand Cherokee that I bought from a dealer. It has about 45000 miles on it. Runs great.

Is there a problem with my Jeep Grand Cherokee dashboard?

The contact owns a 2009 Jeep Grand Cherokee. While driving 25 mph, the electronic dashboard failed without warning. The vehicle was taken to a dealer where it could not be diagnosed. The failure recurred on several occasions. The manufacturer was not made aware of the failure.

What does the warning sign on the Jeep Grand Cherokee mean?

This warning symbol illuminates your Jeep Grand Cherokee to notify you about the airbag sensors’ technical defect. It indicates that these sensors are not blowing well. So, we endorse you once to inspect your Cherokee at the Jeep service centre.

What does the Dashboard Light on a jeep mean?

This dashboard light blinks on your Jeep Grand Cherokee dashboard to indicate that you may not firmly close the door of your Cherokee. So make sure to shut all the doors adequately. This dashboard light illuminates your Jeep Grand Cherokee Instrumental cluster to notify the engine coolant temperature dropping in your Cherokee.

What does the park light on a Jeep Grand Cherokee mean?

This light activates on your Jeep Grand Cherokee when the transmission fluid temperature is running hot. In this situation, Safely stop your car and switch it into PARK mode. This light activates on your Jeep Grand Cherokee instrument cluster to notify you that a vehicle is coming towards your car.

Can you replace blend doors on a Jeep Grand Cherokee?

Thought I’d share my experience of replacing blend doors on my WJ without removing the entire dash. The tech manuals say you have remove the entire dash to replace the blend doors; you do unless you are willing to make a simple cut with the Dremel tool.

Navigation