Where is the serpentine belt on a 2015 Jeep latitude?
I hope I’m on the right platform, I don’t know what KL means, but I have a 2015 Cherokee Latitude, .3.2 engine (V6). I have been searching the web or any information on how to get to my serpentine belt. Its located on the right hand side of the passenger side, I believe that this engine is sideways. .
How is the serpentine belt in a Chev?
Pictures, diagrams of serpentine belt routing. 2.4L. Belt Diagram 3.4 DOHC Cam Engine Drive Belt Diag… 3.5L Engine Serpentine Belt in Chev… 4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro…
How big of a hole do you need for a jeep serpentine belt?
I have had numerous reports from readers that in 2002 Jeep changed the belt-tensioner square hole size to 1/2″. So, you may need a 3/8″ or a 1/2″ breaker-bar depending on what year your vehicle is. SAFETY GLASSES! 1 Serpentine Belt (I use Goodyear Gatorback P/N 4060882)
How do you tighten a serpentine belt on a car?
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.
Pictures, diagrams of serpentine belt routing. 2.4L. Belt Diagram 3.4 DOHC Cam Engine Drive Belt Diag… 3.5L Engine Serpentine Belt in Chev… 4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro…
How is the tension set on a serpentine belt?
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
How do you remove a serpentine belt from a battery?
Use the appropriate sized wrench or socket to loosen the nut holding the black ground cable on the negative terminal of the battery. Slide the cable off of the terminal and tuck it to the side of the battery. You will not need to disconnect the positive terminal. Locate the serpentine belt.
How often should a serpentine belt be replaced?
Most serpentine belts need to be replaced every 40,000 to 70,000 miles. If there are signs of the belt rubbing on something, make sure to identify and repair whatever it was rubbing on to avoid damaging the new belt.
How do you replace a belt on a Jeep Grand Cherokee?
Check the belt routing so you know how to replace the belt. You may be able to find a belt routing diagram on a decal on the fan shroud or in support documentation. Otherwise, make you own sketch for reference. Rotate the belt tensioner pulley, using the wrench, to and relieve tension on the belt.
How to tell if your serpentine belt needs to be replaced?
Look for signs of damage or wear on the belt. Once you have located the serpentine belt, inspect it visually for signs of damage. If the belt is frayed, coming apart, or has marks that indicate that it has been rubbing on something, it will need to be replaced.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
How to remove the serpentine belt on a jeep latitude?
Drain the cooling system. Remove the heater hose (1) at the water pump. Remove the lower radiator hose (2) at the water pump. Release the serpentine belt tensioner (1) by rotating the pulley counterclockwise. Remove the accessory drive belt (4).
Check the belt routing so you know how to replace the belt. You may be able to find a belt routing diagram on a decal on the fan shroud or in support documentation. Otherwise, make you own sketch for reference. Rotate the belt tensioner pulley, using the wrench, to and relieve tension on the belt.
How often should I replace my serpentine belt?
The manufacturer recommends checking the serpentine belt every 7,500 miles or 6 months for potential replacement due to normal wear. Find the belt tensioner pulley. The tensioner pulley is generally between the crankshaft and a component toward the top of the hood area. Check the belt routing so you know how to replace the belt.
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.
What’s the best way to replace a serpentine belt?
Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it.
What kind of pulley does a serpentine belt use?
Determine if there is a belt tensioner pulley. Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times.
What happens if a serpentine belt goes bad?
The serpentine belt in most modern vehicles transfers power from the crank pulley to the various accessories mounted on the engine. A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function.
Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it.
Are there any Jeep Cherokee serpentine belts left in stock?
Only 1 left in stock (more on the way). . Only 5 left in stock (more on the way). . Only 4 left in stock – order soon. . Only 2 left in stock – order soon.
Determine if there is a belt tensioner pulley. Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times.
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.