How to replace the lift gate on a jeep?

This replacement gas strut from Omix fits the lift gate on 99-04 Jeep This replacement gas strut from Omix fits the lift gate on 93-98 Jeep This replacement gas strut from Omix fits the lift gate on 93-98 Jeep This replacement gas strut from Omix fits the lift gate glass on 99-04…

How do you replace a support strut on a liftgate?

Using a small flat blade screwdriver, pry the locking tab away from the socket end of the support strut and pull the strut away from the mounting ball. 5. Position the new support strut over the mounting ball and press to snap it in to place.

Where can I get a new lift gate?

This replacement lift gate strut from Omix fits 06-10 Jeep Commander. This replacement gas strut from Omix fits the lift gate on 99-04 Jeep This replacement gas strut from Omix fits the lift gate on 93-98 Jeep This replacement gas strut from Omix fits the lift gate on 93-98 Jeep …

What do I need to replace tailgate lift support?

This is my detailed procedure for easily replacing weak or failing lift struts on tailgates and is the same for lift gates, hatchbacks, trunk lids, and hoods. These gas charged devices are also called lift supports, shocks, and strut arms whose purpose is the support the weight of the liftgate and make it easy to open and close.

Where can I get lift support for my Jeep Grand Cherokee?

When you begin to notice the hood isn’t staying up like it should, it is time to replace the Grand Cherokee lift supports with high-quality components from AutoZone. AutoZone makes ordering easy with Same Day Store Pickup and ship to home when you shop with us online.

How do you mount a support strut on a liftgate?

Using your torx bit again, mount the lower end of the support strut to the liftgate and tighten the bolt. Before working on the liftgate support struts, be sure to sufficiently support the liftgate, or have a friend hold it up while you’re working. The liftgate is much heavier than it appears.

What kind of gas strut does a 93 Jeep Cherokee need?

This replacement gas strut from Omix fits the lift gate on 93-98 Jeep This replacement gas strut from Omix fits the lift gate on 93-98 Jeep This replacement gas strut from Omix fits the lift gate glass on 99-04… This replacement gas strut from Omix fits the lift gate on 05-10 WK Gr…

Where does water leak from in liftgate Jeep?

If the leak is from the grommet thru the rear flipper glass for the defroster harness, there is a memo for that. See the very bottom of Milous’ TSB page:

Why is there water coming out of my lift gate?

Dried water and sprayed water very easy to resemble rain and when i opened lift gate water rolled off back of hatch and into channel. Water leaked through gasket then out plastic trim in back of head liner . Looks like a gasket leak. I had water that got thought the rubber grommet in the liftgate glass.

What kind of liftgate cover does a jeep wrangle use?

This tailgate bumper by Omix fits 97-01 Jeep Cherokee XJ and 93-98 Jee… This left or right liftgate hinge cover from Omix fits 07-18 Jeep Wran… This liftgate glass to hard top seal from Omix fits 07-10 Jeep Wrangle…

If the leak is from the grommet thru the rear flipper glass for the defroster harness, there is a memo for that. See the very bottom of Milous’ TSB page:

What to do if your liftgate is leaking?

If it’s pooling on the cargo mat, open the liftgate and check the two rubber looms (appx 1.5″ in diameter) that pass through the roof of the cargo area. Not the flipper glass. Make sure they are seated fully. I’ve searched for a similar problem, but couldn’t find one.

How to repair, replace rotted stud wall bottom plate, non?

This is due to the fact that a load bearing wall would require you to erect a temporary stud wall from floor to ceiling a few inches away from the existing stud wall that you want to modify. Then once the new bottom plate is inserted beneath the studs of the load bearing wall, you would then remove the temporary brace wall.

Navigation