What are the torque specifications of a Jeep Cherokee?

31.18 XJ – FRONT Brake Hose to Caliper Inlet Fitting Bolt Type: Bolt 27.12 XJ – Brake Pedel Pivot Pin Nut

How big are the bolts on a flywheel?

The flywheel bolts are stretch to yield and mounting the flywheel calls for 30-40 Nm of initial torque and then a full 90-100° turn of the bolts. This is a tremendous amount torque. Replacing them is best and recommended. But you can reuse the bolts if they measure more then 7.3 mm diameter at the neck.

How big is the balance bolt on a Jeep Cherokee?

Kyle another one for a sticky. BTW good work Jabo. I know this is an old post but I can’t believe nobody has pointed out a lot of the info is incorrect such as harmonic balance bolt and valve cover bolts to name a few…..80 ft lbs on those little 11mm bolts really?? Did you find the recommended reading relevant to this discussion?

How much torque does a 2003 Jeep Wranglers have?

These are all the torque settings that I have at the moment for the 2003 Jeep Wranglers. Ft. Lbs. In. Lbs. Ft. Lbs. In. Lbs. Ft. Lbs. In. Lbs. Ft. Lbs. In. Lbs. Condenser to Radiator Bolts Coolant Overflow Bottle to Plenum mounting bolts – 2.4L only Coolant Pressure Bottle to Plenum mounting bolts Electric Fan to Fan Shroud bolts Ft. Lbs.

31.18 XJ – FRONT Brake Hose to Caliper Inlet Fitting Bolt Type: Bolt 27.12 XJ – Brake Pedel Pivot Pin Nut

Do you know the torque specs for flywheel and pressure plate?

I’m installing the flywheel to the engine and pressure plate to the flywheel either tonight or tomorrow. Does anyone know the torque specs for both set of bolts?

How to torque a brake bracket on a 2015 Cherokee?

Discussion in ‘ Cherokee ‘ started by Gripster, Jan 4, 2020 . Hi, I will be doing a rotor/pad change on a 2015 Cherokee. I read about the one-use-only caliper bracket bolts on your forum – thanks! Purchased the bolts at the local dealer. I cannot find the torque/tightening sequence for these bolts. Does anyone know the correct procedure?

What kind of bolts are in a Jeep Cherokee?

27.12 XJ – Brake Pedel Pivot Pin Nut Type: 7.5 10.17 XJ – REAR Wheel Cylinder Mounting Bolts Type: Bolt 40.67 XJ – FRONT Caliper Mounting (Guide) Pins Type: Bolt 104.4 XJ – FRONT Caliper Achor Plate Bolts Type: Bolt 40.67 XJ – REAR Crossmember to Chassis Sill Bolts Type: Bolt

What kind of drain plug does a Jeep Cherokee use?

XJ – Transfer Case Drain Plug Type: Bolt Head: Hexagon 20 240 27.12 XJ – MANUAL Transmission Drain Plug Type: Bolt Head: Hexagon Drive Shaft To Transfer Case Assembly 22 264 29.83 XJ – Driveshaft to Transfer Case Flange Bolts Type: Bolt Head: Hexagon Drive Shaft To Transfer Case Assembly 35 420 47.45 XJ – FRONT Universal Joint Flange Nut Type:

How to repair a 1999 Grand Cherokee for free?

Access our free Torque Specifications Repair Guide for Cherokee, Grand Cherokee, 1999-2005 through AutoZone Rewards. These diagrams include: Access our Cherokee, Grand Cherokee, 1999-2005 Torque Specifications Repair Guide by creating an account or signing into your AutoZone Rewards account.

How much torque does a 3.8L engine have?

For most of the screws they can simply be snugged up with your screwdriver. If you are rebuilding your engine or simply changing your oil, the torque specs for your 3.8L engine are all in this table.For quick reference the oil pan drain plug should be tightened to 20 ft-lbs.

What kind of engine does a Jeep Grand Cherokee have?

In 2016, FCA released an upgraded Pentastar engine family and a new version of the 3.6L V6 for the Jeep Grand Cherokee and Dodge Durango. The revised engine now has a two-stage variable valve lift (VVL). The VVL system provides low and high valve lifts.

Is there a torque specifications repair guide for Commander?

Find out how to access AutoZone’s Torque Specifications Repair Guide for Commander 2006-2007. Find out how to access AutoZone’s Torque Specifications Repair Guide for 300, 300C & Magnum 2006-2008, Charger 2006-2008. Find out how to access AutoZone’s Torque Specifications Repair Guide for Cherokee, Grand Cherokee, 1999-2005.

How big is front caliper on Cherokee SRT8?

The WK1 SRT8 w/ 4 pot fronts have a steel bridge between caliper halves that are tapped directly, no plug and the FSM are available online free for info purposes and call for 140 ft. lbs. This value is derived from a 2006 LX FSM that I found in a pdf format and it covers the SRT8 models.

How big is the front caliper on a Jeep Grand Cherokee?

This value is derived from a 2006 LX FSM that I found in a pdf format and it covers the SRT8 models. The 4 pot front caliper are identical across all SRT8 chassis up to the ’12-’14 Jeep Grand Cherokee SRT8 WK2.

What kind of brake rotor do I need for my Jeep Cherokee?

Your Jeep Cherokee goes everywhere, but not without the right set of brakes. At AutoZone, we specialize in high-carbon brake rotors for Jeep Cherokee that are precisely machined to match your Jeep’s signature versatility, providing long-lasting performance both on and off the road.

How to find the correct tire size for a Jeep Cherokee?

Jeep Cherokee – Specs of wheel sizes, tires, PCD, Offset and Rims – Wheel-Size.com Jeep Cherokee – Find out the correct alloy wheel fitment, PCD, offset and such specs as bolt pattern, thread size(THD), center bore(CB) for all model years of Jeep Cherokee. Choose a model year to begin narrowing down the correct tire size

How big are the wheels on a 1990 Jeep Cherokee?

It has been corrected. For 1990 Jeep Cherokee 15″ wheels offset is 25 mm. I’m looking to put a 18″ on my jeep … Hi,Jay,Can you explain your questions?

What’s the difference between charger and Cherokee rims?

But the offset differs about 15 mm maybe and the bolt pattern isn’t exactly the same (Charger = 5×115 and Cherokee = 5×114,3). Not a very large difference but it is not recommended, tension might build up in the material/rim even though it’s just 0,7 mm different.

How much torque does a Wrangler YJ engine have?

4.0L & 4.2L Engine Torque Specs Description Specification Camshaft Sprocket Bolt 50 ft-lbs Crankshaft Pulley To Vibration Dampener 20 ft-lbs Cylinder Head Bolts 4.2L 85 ft-lbs Cylinder Head Bolts 4.0L First 22 Then 45 Then 45 Then 100 ft-lbs

What should I do with my Jeep torques?

Jackstands, wheel blocks, disconnecting the battery are a few of the basic safety precautions that should be used and may not be mentioned in the write ups on this site. You are responsible for your own installation, these write ups are a helpful guideline and should not be taken as an official installation instruction.

What are the torque specifications for a Chrysler 5.2L V8?

Oil Pump Cover To Oil Pump 7.92 10.74 Pulley To Vibration Damper/Hub 16.67 22.6 Thrust Plate To Engine Block 17.5 23.73 Timing Chain/Belt Cover To Engine Block 40.67 Timing Chain/Belt Sprocket To Camshaft 47.45 Torque Converter To Flexplate/Driveplate 22.5

Can a Jeep Commander be run at 3000 rpm?

Allowable Stem-to-Guide Clearance (Rocking Method) * CAUTION: If pressure is zero at curb idle, DO NOT run engine at 3000 rpm. Did you find the recommended reading relevant to this discussion?

How much torque does a YJ engine have?

2.5L Engine Torque Specs Description Specification Camshaft Sprocket Bolt 80 ft-lbs Crankshaft Pulley To Vibration Damper Bo 20 ft-lbs Cylinder Head Bolts (1987-1988) Bolt 8 = 75 ft-lbs Rest = 85 ft-lbs Cylinder Head Bolts (1989-1995) Bolt 8 = 100 ft-lbs Rest = 110 ft-lbs

Where can I find the latest torque specs?

Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.

What are the torque specs on a Jeep Cherokee?

Upper nuts are the rear upper nuts, lower nuts are the front lower nuts. No need to torque the stud end of the front shock or the lower rear shock mount. Tighten those till the bushing is snug and tight. For hydraulic lines, torque specs are typically listed in “flats past finger tight.”

Why do I need to torque my Jeep Wrangler?

Remember to torque your Wranlger’s bolts after every modification! When your Wrangler rolled off the factory assembly line, every single nut and bolt of the steering, drivetrain, suspension, and many other areas, were torqued to manufacturer’s specification. The reason for this is that if the bolts were not tight enough they could fall out.

How to install cylinder head on Jeep 4.0L?

Apply sealant to both sides of new cylinder head gasket. Install new gasket with the word “TOP” upward. Ensure all holes are aligned. 2) Install cylinder head. Apply sealing compound to threads of cylinder head bolt No. 11 prior to installation. See Fig. 3. Install head bolts. lbs. (149 N.m) on 4.0L or 85 ft. lbs. (115 N.m) on 4.2L models.

What kind of torque does a jeep lug nut have?

The Jeep Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Jeep vehicle.

What kind of engine does a jeep straight six have?

But the final, and most important reason that these jeeps are so coveted, is the 4.0L in-line “straight six” AMC engine. Chrysler’s 4.0L Straight Six Engine The 4.0L AMC inline six is known as one of Chrysler’s best engines. Dating back to 1986, its torquey 190 hp engine would commonly chug along for upwards of 300,000 miles.

What kind of engine does a Jeep Grand Cherokee use?

The inline six has powered Cherokees, Grand Cherokees, Wagoneers, Wranglers, and even Comanches. We think its best known for its time with the Cherokee, but it remains a major selling point no matter what it’s been dropped in. Unfortunately, the AMC 4.0L inline six was replaced by the 3.8 OHV V6, which originated in Chrysler minivans.

When did the Jeep Grand Cherokee inline six come out?

Dating back to 1986, its torquey 190 hp engine would commonly chug along for upwards of 300,000 miles. Over the course of nearly 20 years this engine was refined and tweaked before being phased out in 2006. The inline six has powered Cherokees, Grand Cherokees, Wagoneers, Wranglers, and even Comanches.

How big are the bolts on a jeep?

OH NO! This chart, lists out most of the common bolts and nuts you will encounter while working on your Jeep as well as the torque settings required for each of them. 13mm. 15mm. T-55. NO PURCHASE OR PAYMENT OF ANY KIND IS NECESSARY TO ENTER OR WIN.

How to repair a 1999 Jeep Grand Cherokee?

These diagrams include: Access our Cherokee, Grand Cherokee, 1999-2005 Torque Specifications Repair Guide by creating an account or signing into your AutoZone Rewards account. Once you sign in, follow these instructions to access our Repair Guides. Add your vehicle in Manage My Vehicles. Enter your vehicle details.

Where can I find torque specifications repair guide?

Once you sign in, follow these instructions to access our Repair Guides. Add your vehicle in Manage My Vehicles. Enter your vehicle details. Click the “View More” button, and then click “Vehicle Repair Guides.” Select the chapter “Torque Specifications Repair Guide”.

Why does my Jeep Grand Cherokee whine when I accelerate?

The power steering pump is a very common reason why your Jeep Grand Cherokee might whine when accelerating. If it gets too low on fluid they’ll make the it’ll whine a lot. You need to check the fluid level and fill it back up to the factory fill line.

How much horsepower does a 1999 Jeep Grand Cherokee have?

The 1999 Jeep Grand Cherokee (WJ) 4.7i V8 has 230 PS / 227 bhp / 169 kW horsepower. How much does a Jeep Grand Cherokee (WJ) 4.7i V8 weighs? What is the top speed of a Jeep Grand Cherokee (WJ) 4.7i V8? Is Jeep Grand Cherokee (WJ) 4.7i V8 All Wheel Drive (AWD)? Yes, the Jeep Grand Cherokee (WJ) 4.7i V8 is All Wheel Drive (AWD).

What is the top speed of a Jeep Grand Cherokee?

With a fuel consumption of 15.8 litres/100km – 18 mpg UK – 15 mpg US (Average), 0 to 100 km/h (62mph) in 8.3 seconds, a maximum top speed of 122 mph (196 km/h), a curb weight of 4050 lbs (1837 kgs), the Grand Cherokee (WJ) 4.7i V8 has a naturally-aspirated V 8 cylinder engine, Petrol motor.

The 4.7 V8 engine also features a modern coil-on-plug ignition system and a hybrid cooling fan system (in-line electric and engine-driven fans). In 2002, Chrysler introduced a “High-Output” version of the 4.7L PowerTech engine as an option for the Jeep Grand Cherokee Limited and standard for the Overland models.

Where can I get torque for my Jeep Wrangler?

Find the aftermarket Wrangler parts you need, at ExtremeTerrain. Remember to torque your Wranlger’s bolts after every modification! When your Wrangler rolled off the factory assembly line, every single nut and bolt of the steering, drivetrain, suspension, and many other areas, were torqued to manufacturer’s specification.

Why did my torque nut snap on my Jeep Wrangler?

If the bolts were over-tightened they could get stuck in the hole, snap, or pull the threads out. During routine maintenance and after doing any kind of modification to your steering, suspension, or drivetrain, all bolts and nuts should be checked to ensure that they have been tightened to specification.

Where is the slip yoke located on a Jeep XJ?

The slip yoke is located on the output shaft of the transfer case. On 84-95 models, the yoke slides in and out of the transfer case and is lubricated by the ATF fluid internally. On 96-01 due to a design change, the slip yoke is external (does not slide in and out of the transfer case).

What is the correct tyre pressure for a Jeep Grand Cherokee?

The chart also lists the Jeep Grand Cherokee Wheel Nut Torque Setting. What is the correct tyre pressure for a Jeep Grand Cherokee ? What is the correct wheel nut torque setting for a Jeep Grand Cherokee ?

. The available 5.7L HEMI ® V8 engine provides up to 360 horsepower and 390 lb-ft of torque for a maximum towing capacity of up to 7,200 pounds ( Disclosure 3). Fuel saving technology automatically deactivates four cylinders for added maximum efficiency when all eight are not necessary.

Which is the Best 4×4 system for Jeep Grand Cherokee?

The Quadra-Drive® II is our most advanced 4×4 system. Standard on Grand Cherokee Trailhawk®, it delivers superior off-road capability by transferring up to 100% of engine torque to a single wheel if needed.

Where can I find air pressure on my Jeep Grand Cherokee?

This cars tyre air pressure guide chart can in some cases contain actual tyre pressure placards from a Jeep Grand Cherokee which can list the space saver tyre pressure and the laden / fully loaded tyre pressure. To find the right pressure you will require the vehicles current tyre size and the vehicle’s year of manufacture.

What are the torque specifications for an Amc 2.5L 150ci?

Flexplate/Driveplate To Crankshaft 40 480 54.23 Drive Plate Bolts – 2 Step: 40FtLbs; +60deg Type: Bolt 50 600 67.79 Flywheel Bolts – 2 Step: 50FtLbs; +60deg Type: Bolt 16 192 21.69 Mechanical Fuel Pump Mounting Bolts Type: Bolt Head: Hexagon Intake Manifold To Cylinder Head 23 276 31.18 Type: Bolt Head: Hexagon 7 84 9.49 Type: Bolt

How much torque does a drive plate have?

480 54.23 Drive Plate Bolts – 2 Step: 40FtLbs; +60deg Type: Bolt 50 600 67.79 Flywheel Bolts – 2 Step: 50FtLbs; +60deg Type: Bolt 16 192 21.69 Mechanical Fuel Pump Mounting Bolts

Is the slip yoke external on a Jeep XJ?

On 96-01 due to a design change, the slip yoke is external (does not slide in and out of the transfer case). This slip yoke is covered with a rubber boot. (Note on Dana 35 axles sometimes referred to as Dana 35C – The “C” does not stand for c-clip. It stands for “custom” meaning it came from Dana unfinished.)

How many axles are in a Jeep Cherokee?

I only have data going up to 1997 so if you can add to this list it would be greatly appreciated. Axles are grouped by part number rather than year of vehicle. This information was compiled as a result of trying to run down various axle id’s & not having a good single source to start from that also gave part numbers.

What are torque specs on 66 El Camino?

Hey everyone! Enter your ride HERE to be a part JUNE’s Ride of the Month Challenge! Working on a 66 El Camino and I have been looking all over for torque specs. Installing new A-Arms, Spindles, and steering with a disc brake conversion. Here are the specs that I need. There are a few that I have found, please correct me if I am wrong.

What kind of torque does a fox body Mustang have?

A list of torque specifications for your fox body Mustang’s suspension and steering systems.

Where can I get a Chevelle torque manual?

They are only around 20-25 a piece. Borrow them free at the library. I have thought about the manuals. If someone has one with the numbers that I need that would be great. Not available at library and I can not wait 4-6 more weeks to get the car back together. Click to expand…

Navigation