Where is the fuel pump on a 1996 Jeep Cherokee?

Changing the fuel pump on your 1996 Jeep Cherokee Classic can alleviate many problems related to the fuel system, including inadequate acceleration or engine stuttering due to poor fuel delivery. The pump is easily accessible and is located in the fuel tank.

How to remove gas pump from Jeep classic?

Care must be taken while removing the pump, and using metal tools on metal surfaces should be kept to a minimum, lowering the chances of a spark-related fire. The 1996 Jeep Cherokee Classic models, all with 4.0 engines, use an electric pump. Disconnect the negative battery cable with a wrench. Remove the gas cap.

What to do if your Jeep Cherokee stops running?

If the Jeep Cherokee has stopped running or will not start and you feel that the fuel pump has failed, then this is the proper way of diagnosing the problem before replacing an item that may not be needed. Starting from the basics, take off the fuel cap and listen closely for the fuel pump to come on as a helper turns on the ignition key.

Where are the fuses in a Jeep Cherokee?

Here you will find fuse box diagrams of Jeep Cherokee 1997, 1998, 1999, 2000 and 2001, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay. Cigar lighter (power outlet) fuses in the Jeep Cherokee are the fuses #1 and #2 in the Instrument panel fuse box.

When to replace fuel pump module on Jeep XJ?

Please try again later. Replacing fuel pump module on 1999 Jeep Cherokee XJ. Bosch pump module. Should be same procedure for all 1997+ XJ’s. Used my old FlipHD to record this, as it fits onto of my tripod and I don’t mind getting it dirty, still works well. Loading…

Where is the check valve on a Jeep Cherokee?

Well, I replaced the fuel pump, both fuel filters, and the fuel pressure regulator with the check valve on top of the tank. The jeep now starts easily and the check valve seems to be doing what it’s supposed to be doing. I was unable to get any pictures, as I was so greasy and grimy the last thing I wanted to touch was my camera.

How do you remove a fuel pump from a car?

Disconnect the hoses running to and from the fuel pump and the electrical connections running to the fuel pump and the attached fuel sending unit. Turn the ring holding the fuel pump and fuel sending unit counterclockwise until it can be removed from the outer retaining ring. Remove the mounting bracket and place it onto the new fuel pump.

Why do I need a new fuel pump for my Jeep Cherokee?

A broken fuel pump affects those dynamics by causing the engine to surge, sputter or not start at all. You need a fuel pump replacement for Jeep Cherokee from AutoZone to get your Jeep back to driving up to standard. Your Jeep Cherokee fuel pump uses pressure to feed gas through a line from the fuel tank to the engine.

Where is the fuel pump connector on a jeep?

Unplug the fuel pump connector at the back of the fuel tank. It will be easy to find and has four wires in the connector. Use a circuit tester and test the harness side for power as your helper turns the key on and off.

What to do when your fuel pump wont turn on?

The computer shuts the power off to the pump if it does not see a signal from the crankshaft sensor. Have the helper turn on the key for 3 seconds and off for 5 seconds and on again a couple of times. If the pump cannot be heard, then replace the cap and lift the hood. Check to see if the fuse to the fuel pump is good.

How does the fuel pump relay work in a jeep?

As you’re cranking the engine to get it started…. the PCM maintains the fuel pump relay activated only if it receives a crankshaft and camshaft position sensor signal (that shows the engine cranking or running). If either sensor indicates no engine RPMs, the PCM will not activate the fuel pump relay past the 1-3 seconds initial run time.

Where does the fuel pump go in a Jeep Grand Cherokee?

1993, 1994, 1995 4.0L Jeep Grand Cherokee. Fuel pump troubleshooting notes: The fuel pump relay gets power from fuse #6 (15 Amp) of the Power Distribution Center (PDC). The PCM activates the fuel pump relay and the auto shut down (ASD) relay at the exact same time and thru’ the same circuit (PNK wire).

What is the fuel pressure on a Jeep Grand Cherokee?

If either sensor indicates no engine RPMs, the PCM will not activate the fuel pump relay past the 1-3 seconds initial run time. Key On Engine Running: 31 PSI (2.2kg/cm²). Key On Engine Off: 39-41 PSI (2.7-2.9kg/cm²). Key On Engine Running (but no vacuum applied to fuel pressure regulator): 39-41 PSI (2.7-2.9kg/cm²).

How do you remove a fuel pump from a tank?

Remove fuel pump mounting bolts or retainer ring to access the fuel pump module and remove the unit. Use a hammer and punch to remove the ring counterclockwise. Remove the fuel pump which will be attached to the mounting plate or positioned down inside the tank held by plastic retainer clips. Here is a typical fuel pump removed from the fuel tank.

Refer to your service manual for instructions on removing the fuel pump assembly from the tank. There’s typically a plate held in place with screws or bolts, which, once released, enables removal of the pump. Install the new pump in the opposite order you used to remove the old one.

What to do with a 1996 Jeep classic?

The 1996 Jeep Cherokee Classic models, all with 4.0 engines, use an electric pump. Disconnect the negative battery cable with a wrench. Remove the gas cap. Locate the test port and place towels around the port. Use a small screwdriver to press against the port and relieve the fuel pressure.

Why do I need a gas pump for my Jeep Grand Cherokee?

Pressure changes lead to the engine jerking when you accelerate or to sputtering at high speeds. Faulty pumps allow too much fuel to pass to the engine, which drastically increases your gas usage. A high-quality Jeep Grand Cherokee fuel pump from AutoZone eliminates these issues.

Can a fuel pump be replaced if there is no power?

If there is power, the fuel pump took a dump and needs to be replaced. If there is no power, there is an open in the harness to the pump from the fuse block. This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.

How to test fuel pump in Jeep Cherokee?

Use a circuit tester and test the harness side for power as your helper turns the key on and off. Remember that there will be power for only 2 seconds, so have your helper cycle the key on and off as you check the terminals, allowing 5 seconds between cycling for the computer to reset.

Can a fuel pump run when there is no power?

If there is no power, there is an open in the harness to the pump from the fuse block. Don Bowman has been writing for various websites and several online magazines since 2008.

Why does my Jeep stall when I start the engine?

If it starts, the fuel pump is the problem. If not, the engine should be checked for spark. It could be a sensor or computer-related problem. To be absolutely sure, raise and support the back of the Jeep on jack stands, unless the height allows you to crawl under the back without raising it.

Can you replace the fuel tank on a Jeep Cherokee?

We stock everything you need to get the most out of your Jeep and we provide the right products at the right prices for added value. A replacement Jeep Cherokee fuel tank is designed to fit perfectly according to the mounting points and original manufacturer’s specifications, making installation a snap.

Where is the fuel filter located on a Jeep Grand Cherokee?

Jeep Cherokee (1984-2001); Grand Cherokee (1993-2004): nut/bolt sizes may vary, but the removal process is similar. Pull Tip: On later model Cherokee there is no replaceable fuel filter. The fuel filter resides in the pump and is suppose to last the lifetime of the pump.

How do you drain a fuel tank in a jeep?

For safety and environmental reasons, Pull-A-Part punches a hole in the fuel tank to drain the fuel. Use a ratcheting wrench to loosen the tank straps or just cut them off with a sawzall if you don’t need to reuse them. Remove the electrical connectors by pinching the clips and pulling the connectors apart.

How do you install a new fuel pump?

Turn the ring holding the fuel pump and fuel sending unit counterclockwise until it can be removed from the outer retaining ring. Remove the mounting bracket and place it onto the new fuel pump. Disconnect the wires from the old fuel pump and attach them to the new fuel pump. Install the lock ring onto the new pump.

Install the new fuel pump using the items included in the kit, especially the rubber gasket for the fuel tank. Rotate the fuel pump until the alignment arrow points toward the alignment mark. Be sure the fitting on top of the fuel pump faces towards the driver’s side. Tighten the lock ring with tool 9340 until all seven notches engage.

How do you remove the lock ring on a fuel pump?

Remove the lock ring on the fuel pump using tool 9340 with a ½ inch drive breaker bar to rotate the lock ring counter-clockwise. The fuel pump should rise up slightly when you remove the lock ring. Remove the fuel pump using care not to bend the float arm.

What happens if your fuel pump is failing?

The fuel pump feeds fuel to the engine at a reliable rate; without this pump, your fuel would just sit in your tank, useless and inert. If you’re attentive, you can catch the symptoms of a failing fuel pump and have it repaired or replaced before it leaves you stranded on the side of the road.

Where is the fuel pump in a car?

To resolve this issue, the fuel tank must be accessed and repaired or removed. The location of the fuel tank depends on the construction of the vehicle. In a vehicle equipped with a carburetor, the fuel pump is often located outside of the fuel tank. With a vehicle that has a fuel injector, the fuel pump is located inside of the tank.

Can a Jeep Grand Cherokee Run without gas?

Without gas your Grand Cherokee will not run at all. With that in mind, most of the symptoms of a bad fuel pump revolve around the vehicle stalling out or not running at all. In modern fuel injected vehicles, the fuel pump sits right in the fuel tank and “pushes” the gasoline to the fuel rail (s).

What are the symptoms of a bad fuel pump?

Jeep Grand Cherokee Bad Fuel Pump Symptoms. 1 Whining Noise. One of the most common signs that a fuel pump is going bad is a whining sound. The whining sound can indicate that the fuel pump is 2 Sputtering Under Acceleration. 3 Challenges Starting the Engine. 4 Engine Won’t Start.

Where does the fuel pump go in a car?

In modern fuel injected vehicles, the fuel pump sits right in the fuel tank and “pushes” the gasoline to the fuel rail (s). It is in the fuel tank because “pushing” fuel to the fuel rail is easier than “pulling” the fuel, which is what an inline pump would do.

Navigation