What does the code po333 knock sensor 2 mean?
We are having problems with fixing the problem on our 2001 Subaru Outback 3.0L. The code we got is PO333 Knock Sensor 2 Circuit High Input Bank 2. We are not sure which side is Bank 2 and does this mean the sensor itself needs to be replaced or does this mean the wires to the sensor are faulty?
What does the p0333 code on my car mean?
All our repairs are backed by our 12-month / 12,000-mile warranty. The P0333 code indicates that your car’s computer has detected an input reading for one cylinder’s knock sensor circuit that goes beyond the manufacturer’s limit.
Why is the knock sensor on my Jaguar not working?
The Jaguar knock sensor on the passenger side below the intake manifold is not making solid contact with the engine, due to it overheating. Take the cover off the engine and look through the runner to check for any damage to the connector where the knock sensor is clipped onto the thermostat housing.
What are the symptoms of a p0333 DTC?
Symptoms of a P0333 DTC may include: MIL (Malfunction Indicator Lamp) illumination Audible knocking from the engine compartment Pinging from engine under acceleration Potential causes of a P0333 code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage
What does the p0333 code mean on a knock sensor?
A P0333 code is a generic DTC, thus it applies to all makes of vehicles, and refers to a high output voltage of the knock sensor. In many cases, this means the voltage is above 4.5V but that specific value depends on the specific make and model of vehicle.
Symptoms of a P0333 DTC may include: MIL (Malfunction Indicator Lamp) illumination Audible knocking from the engine compartment Pinging from engine under acceleration Potential causes of a P0333 code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage
What is the diagnostic code for knock sensor 2?
P0333 is a diagnostic trouble code (DTC) for “Knock Sensor 2 Circuit High Input (Bank 2)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
What causes a knock sensor to ping under acceleration?
Pinging from engine under acceleration Potential causes of a P0333 code include: Knock sensor connector is damaged Knock sensor circuit is open or shorted to ground Knock sensor circuit is shorted to voltage Electrical interference in circuit Mechanical engine problem
What does the p0333 code on Bank 2 mean?
What the P0333 code means. The P0333 code means that the input voltage from a knock sensor circuit in one of the cylinders on bank 2 is higher than the manufacturer’s limitation. In most instances, a 10% variation is needed for this code to set. However, your vehicle will likely require multiple instances to set the code.
What does knock sensor 1 circuit high input mean?
Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) What does that mean? This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model.
P0333 is a diagnostic trouble code (DTC) for “Knock Sensor 2 Circuit High Input (Bank 2)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
We are having problems with fixing the problem on our 2001 Subaru Outback 3.0L. The code we got is PO333 Knock Sensor 2 Circuit High Input Bank 2. We are not sure which side is Bank 2 and does this mean the sensor itself needs to be replaced or does this mean the wires to the sensor are faulty?
What does p0333 stand for in PCM?
P0333 stands for knock sensor high input. This means the PCM has detected a problem with the knock sensor or its circuit. Some vehicles may be equipped with two knock sensors. Code P0333 pertains to the sensor on bank 2 (the opposite side of the engine where the #1 cylinder is located).
Where is the knock sensor on Bank 2?
Code P0333 pertains to the sensor on bank 2 (the opposite side of the engine where the #1 cylinder is located). What are the common causes of code P0333 ? To sum things up, the common causes for code P0333 are as follows: What are the symptoms of code P0333 ? You may notice a lack of power, hesitation and/or pinging.
What the P0333 code means. The P0333 code means that the input voltage from a knock sensor circuit in one of the cylinders on bank 2 is higher than the manufacturer’s limitation. In most instances, a 10% variation is needed for this code to set. However, your vehicle will likely require multiple instances to set the code.
Why do I get a p0330 error code?
Here are the possible causes of the P0330 error code: 1 Defective knock sensor 2 Issues with the knock sensor circuit (e.g., damaged wiring or poor connections) 3 PCM issues 4 Engine mechanical problems