How to install new GM wire harness on fuel pump module?
If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: WfYJuntPOgNiQAf9)
Do you need to remove wire from fuel pump?
You’ll need to remove about a foot of the wire harness and the conduit from the old wire harness before you start cutting. Make sure you’re dealing with the one four wire connector for the fuel pump module, and not the fuel pump’s fuel pressure sensor connector.
What are the connectors for a fuel pump?
The connectors are two different sizes, for the larger wires for the ground and the supply for the fuel pump, and the smaller ones for the fuel stemming unit. Make sure you crimp them firmly, and make sure you don’t get any of the insulation trapped in between the electrical connective crimp.
Can You Heat shrink a fuel pump connector?
To heat shrink these connectors, you want to make sure you use a heat gun, not any open flame source. Also, be sure to keep it away from any fuel spills that may have occurred. Make sure you got that fire extinguisher on hand.
How to remove a fuel pump from a truck?
Basic instructions on how to tip your bed and remove your fuel pump and sender assembly, replacement of the fuel pump from the sender unit and putting it back into the tank with gasket o-ring and lock ring. I also show video of the bolt hole locations on my short bed frame. Loading…
Why does my fuel pump not start when I change it?
You always want to replace the fuel filter when replacing the fuel pump. This could cause the concern you are having. It may seem as you are getting enough fuel from the pressure regulator but if the pressure from the fuel tank is not correct, it will still not start. Another problem you could be having is spark.
What happens when the fuel pump goes out on a GMC Sierra?
There are physical signs that you can feel when your Sierra’s fuel pump is going out. Before taking anything apart, check to see if your engine’s computer has any trouble codes saved in it. The engine may throw a P0087 trouble code. This trouble code detects that the fuel rail/system pressure is too low.
Basic instructions on how to tip your bed and remove your fuel pump and sender assembly, replacement of the fuel pump from the sender unit and putting it back into the tank with gasket o-ring and lock ring. I also show video of the bolt hole locations on my short bed frame. Loading…
If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: WfYJuntPOgNiQAf9)
What are the symptoms of a bad fuel pump?
Also, the symptoms are almost exactly the same as bad/clogged fuel filter. Here are the most common symptoms of a bad fuel pump in your GMC Sierra: One of the most common signs that a fuel pump is going bad is a whining sound. The whining sound can indicate that the fuel pump is going out before there are any performance based issues.
How to tell which wire is positive in a fuel pump?
To find out which one is positive and which is negative pull the wire loom back and look @ the colors of the wires. Doing it this way will make the pump run constantly, because on start up it only runs for a second or 2, this way you can check pressure to the fuel rail w/o the engine having to run in the event you can’t get the engine to start.
Can a fuel pump connector be used on a Dodge Ram?
Good connector, toss the wires it comes with though! The connector was a perfect match for the broken one on my Dodge Ram’s fuel pump, but the wires are much thinner & cheaper than the factory wires were. So I took it apart and installed it onto my factor wires and pins, that worked for me.
Are there any Jeep Wrangler fuel harness left in stock?
Only 2 left in stock – order soon. . . Only 7 left in stock – order soon. . . Only 11 left in stock – order soon. . Only 2 left in stock – order soon.
What kind of wiring harness does a dune buggy use?
COMPLETE ENGINE & CAR WIRING HARNESS. Vw dune buggy plug and play wiring harness.14 inch chopped pan. Meyers manx etc. Have your iPhone or iPad “speak” to the electronic computer systems in your BMW or MINI with Y lightning USB to AUX lead cables.
Do you need engine with swap specialties harness?
YOU NEED THIS TO RUN CORRECTLY IF YOUR ENGINE DID NOT COME WITH IT. This order is subject to all Terms and Conditions found at swapspecialties.com/sale-terms. Please let us know if you have any questions, we would love to hear about your project and help in any way we can!