Why does my Harley Davidson bike not start?

BIke won’t start. Acts like a dead battery but it isn’t! | Harley Davidson Forums BIke won’t start. Acts like a dead battery but it isn’t!

What does it mean when your car wont start but battery is good?

While a partially clogged filter might not prevent your vehicle from starting, a completely clogged filter doesn’t allow any fuel from getting to the engine, and thus, your vehicle won’t start even if you have a good battery.

Why does my bike not start in ACC mode?

I just found out the hard way, if it is doing that your key switch has 3 balls and springs, in ACC mode, it only relies on 2 balls and springs, once put all the way into ignition, it requires the all 3 balls and springs to work in contact…I can guarantee that the ignition mode ball and spring have corroded and failed.

BIke won’t start. Acts like a dead battery but it isn’t! | Harley Davidson Forums BIke won’t start. Acts like a dead battery but it isn’t!

What happens when you disconnect the battery on a Harley?

Since disconnecting the battery on my harley it wont start. Bike still has power all lights etc since disconnecting the battery on my harley it wont start. Hey there!

What to do if your car battery won’t start?

If the replaced battery car won’t start, the first thing to check is whether you replaced the battery correctly. Are the cable clamps tight? Are the cables themselves in good shape?

What to do if you have a bad starter?

– You have a bad starter. Check out common car parts when seeking car part replacements. – Dirt or residue may be on the inside of the connectors. – The new battery may need to be fully charged before installing it into your car. – Make sure there is a solid connection between the cables and the battery.

What to do when your Harley Davidson won’t start?

Try neutral with clutch pulled in. Also battery connections , solenoid wire. The security system lights only flash after I turn off the bike. I have the bike in neutral and I even tried pulling in the clutch a couple of times. I checked the wire to the solenoid and it had power.

What should I do if my battery charger is not working?

Almost certainly it’s a battery problem, either low charge or bad cable connection. Charge the battery on a good bench charger, not a Tender, but a real charger. Remove and reconnect both battery cables making sure they are tight and connections are clean. This sounds like a discharged battery to me just saying.

Whenever you are trying to diagnose why your bike won’t start, it is always a good idea to remember the elements that allow for combustion to occur: fuel, spark, and battery power. Especially with fuel injected models, if any one of these three elements is removed from the equation, you end up with an engine that will not run.

Is there an issue with my electric bike battery?

Has anyone ever had an issue with the battery not charging? It has happened to me a few times now, where I plug in the battery to charge and the charger indicator light just keeps flashing green to signify ‘Standby’ mode. Checking all the plugs on the leads are secured.

How can you tell if a Harley Davidson ignition coil is bad?

Harleys’ that run on a single-coil engine will make cranking sound, but there will be no spark from the cylinders. If your bike stalls while working, this is another sign that indicates there’s something wrong with the ignition coil. When some irregular sparks are sent to plugs from the coil, the issue occurs.

What to do if your Dyna bike won’t start?

Apparently, starter issues are quite common on various Dyna models, so if yours is in need of replacement, see How to Replace Starter. If you are in a bind and your starter motor is acting up, a quick tap of the solenoid with a hammer or similar small object can sometimes free the starter to start the bike.

How can I tell if my motorcycle battery is over charged?

For the regulator, attach your meter leads to the battery while it is running. It should not read higher than 14.5 volts and no lower than 13.5 volts. If it is higher, the battery will be over charged and if it is lower, the battery will continue to drain as the bike runs. If these tests do not check out, you will need a new regulator/rectifier.

If you can start the bike this way; the start switch is probably bad, or a wire may be damaged. Let us know what you find. Sounds like you know what you are doing. You are not going to believe this – but – it was the battery in the key fob. The bike has to have a signal from the key fob before it will allow the bike to start.

What’s the voltage on a Harley Davidson starter?

I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.

Is there a problem with my Sportster 1200 XLH?

Before I go out and buy parts I think I need, maybe somebody can jump in and pinpoint the problem. 1995 Sportster 1200 XLH. Ride it daily to work. Last Friday I shut the motor off with the stop switch and then turned the ignition key off.

What to do if your motorcycle relay won’t turn?

If you don’t have a meter, disconnect the wiring at the solenoid and run a jumper wire straight from the battery to it to see if it turns. Disconnect the plug wires if you don’t want it to actually start! Check the voltage coming out of the relay when it clicks.

Why does my Harley won’t start up?

Common Reasons Why Harley Won’t Start Troubleshooting Weak or Dead Battery This is the first major reason you might be having a problem starting your bike. If you are experiencing very dim light or if the light goes off when you turn on the ignition, it could be that your battery is dead.

What should I do if my motorcycle battery wont start?

If you don’t see these symptoms or are otherwise unsure what to look for, the first step is ensuring that the battery is operational and providing the maximum voltage. To confirm your battery is still good, you should visually inspect it, check the voltage, and load test the battery. A visual battery inspection should involve:

Why is my battery not cranking on my Harley?

If the battery can no longer crank the starter and can no hold a charge for long, it’s due for replacement. If after all the cranking and the bike is still not cranking, it could be that one of the electrical wires may be off.

Where is the start relay on a Harley Davidson?

It is the GRAY one. On the inside cover there is a label that will identify the START Relay. 4) Look at the bottom of the removed gray relay closely. You will see pin notation as follows. 87,,87A,,30,,85,,86. 5) Leave the relay REMOVED from the bike.

Why is the fuel pump not working on my Harley?

Key fob battery was dead. Discovered that with a good battery in the fob when I turn ignition to on I can hear the fuel pump charging the system. When the fob is out of range everything works except the fuel pump. Hence the no start issue. Thank you a thousand times over. I spent Over two hours checking every electrical item I could.

Why does my Harley Davidson bike not turn over?

Can’t even push start it! After riding my bike will not turn over. It acts like the motor is locked up but it isn’t because we push it and it turns over but doesn’t fire up. It starts using the starter after setting 2-3 hrs. While pushing I try to engage starter but it wont turn the motor over.

If the engine doesn’t crank, it could be because of a failure at any of those stages, a weak battery, or a bad starter. If the motor cranks and still won’t start, then it is likely a fuel or spark issue. A few tests can be performed to quickly track down the problem.

What to do if your Harley does not have a spark?

If you do not see any sort of spark, turn your bike on. Sometimes, ignition switches can malfunction and might not work properly under that situation. Besides, if your Harley has a security system installed, it might not be getting the juice properly. And that might hinder the bike from turning on.

Can a bad ignition coil cause a bike to stall?

When fuel is present more than air, it is rich and otherwise, it is lean. Vehicle stalling: Bad ignition coil will cause your bike to stall while the engine is working. The engine does not start: one of the most common signs of a bad ignition coil is when the engine fails to start. Rough idling: Weak ignition coils make the bike jerk.

What should I do if my fuel injected Harley wont start?

On fuel injected models, make sure that you can hear the fuel pump cycle when switched to RUN. If not, check your fuses. As always, the best way to avoid being stranded with your Harley Davidson is to be diligent about your bike’s maintenance.

What should I do if my motorcycle won’t start?

How to fix it: There is only one fuse that can affect the starting of a motorcycle. Every motorcycle usually has a main fuse which is between 30 to 50 amps (occasionally some bikes will have 20 amps). It is usually located off of the positive battery wire.

Why are the lights on my Harley not working?

I went out to start up my bike and noticed that the lights and horn were not working and the headlights a … read more Disclaimer: Information in questions, answers, and other posts on this site (“Posts”) comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts.

What does no start no crank no click mean?

If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that. In the old days, power flowed through the ignition switch and down to the starter solenoid. Not anymore.

Why does my starter click when trying to start?

The starter will either push the jack shaft out and spin (then the starter is good )or the jackshaft will click in and out rapidly and then you’ll know it’s the solenoid hold in coil. But it’s probably just the battery. Was this answer helpful?

What to do when your bike won’t start?

Linduy, Clean and tighten all connections from battery to the starter and all grounds, as this can be a big issue on bikes. Have battery tested at auto parts store, a lot offer free battery testing and can give you print out of the status on battery.

When I turn on the bike and put it in the run position, the fuel pump kicks on, but when I push the start switch the bike doesn’t even try to turn over. The battery is fully charged and the fuel pump turns on when I push the switch, but nothing else happens.

If the reading stays steady, your battery is good to go—and your motorcycle likely has another problem (or a few problems). Fortunately, there are other troubleshooting means that can help determine why your bike won’t start.

Why does my motorcycle not start with the side stand down?

Newer bikes (and some older ones) may refuse to start with the side stand down. Along with all the other high-tech sensors that are on board, your motorcycle might have a built-in code that keeps the ignition from starting if your kickstand is engaged.

How to start a bike without a fob?

Here is how to use the code you jus entered to start your bike without the Fob present!! 1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window. 2. Enter the first digit of your PIN (a) by pressing the left turn signal switch (a) times.

What should the current be on a Harley Davidson starter?

In addition to the starter current draw test, you can measure the voltage at the wire connected to the starter solenoid from the ignition switch. With the ignition in the on/run position and the button pressed, 12 volts should be present at this wire.

Where is the starter on a Harley Davidson 883 Sportster?

Connect your red probe to the solenoid positive wire. This is a fat 12 or 14 gauge wire on the cylindrical portion of the starter. Connect the black probe to a known good ground. 12v should be present in this wire at all times. Figure 3. The starter location on a 883 Sportster.

How often does a Harley Davidson engine fail?

This metal-to-metal contact promotes engine failures which can be dangerous to you and your bike. This problem can occur anywhere from 15,000 to 75,000 miles depending on the severity. The only way to truly avoid this problem is to completely swap out the chain system for a gear-driven system.

What is the displacement of a Harley Davidson 88B engine?

Although they’ve subsequently been 88B models. Read on for a brief overview of the specs of these engines. cubic inches. The 88B is 96 cubic inches, for a total of 1584 cc displacement. This is a marked improvement over the previous engine models, allowing for greater horsepower for the motorcycles. 88B twin cam engines is the dual coil system.

What was the first production Harley Davidson engine?

– Jeff Leighton’s 1942 Harley-Davidson Flathead at Born Free 8. Made from 1936 through 1947, the Harley-Davidson Knucklehead motor was Harley’s first production bike to have overhead valves. A more-efficient circulating oil lubrication system on the knucklehead replaced the “total-loss” lubrication system that previous models featured.

How often do new Harley Davidson engines come out?

For more than 100 years, Harley-Davidson has been producing its legendary lineup of Big Twin engines. Through the decades, various technological advances have led the company to develop nine different types of basic Big Twin motors. New Harley-Davidson engine designs arrive about every 15 years.

How big is a Harley Davidson 88 twin cam engine?

The total displacement of the 88 twin cam engine is 1450 cc, or 88

Why do the lights keep blinking on my Harley?

The lights keep blinking and the ignition won’t turn over. It has been in storage for a year. Submitted: 11 years ago. Category: Motorcycle If you have stored the bike it may have went into storage mode. Do dissable that, turn the ignition to on and the system should flash and go CRAZY! Double click the FOB and it should disarm.

Where does the Blk / red wire go on a bike?

Try jumping 12 volts directly from the battery to where this blk/red wire enters the relay plug. See what the outcome is. You may also want to try this with the blk/red wire removed from the relay plug. If you can start the bike this way; the start switch is probably bad, or a wire may be damaged. Let us know what you find.

When did I replace the battery on my Street Glide?

I have a 2014 Street Glide Special with about 40k miles. I replace the main battery in February and then last week I took the bike for a ride. After stopping for a drink, the bike would not start.

Why does my bike light flash when I turn it off?

The security system lights only flash after I turn off the bike. I have the bike in neutral and I even tried pulling in the clutch a couple of times. I checked the wire to the solenoid and it had power. Almost certainly it’s a battery problem, either low charge or bad cable connection.

The clutch switch is part of an interlock system that prevents starting the bike with the transmission in gear unless the clutch lever is pulled in. Besides checking the start/run switch, also make sure the bike’s transmission is in neutral to eliminate this possibility for the no-start problem.

Why does my motorcycle battery last so long?

More than likely, you have a problem with your motorcycle’s electrical system and not the battery.

How many volts does a motorcycle battery need to be?

A healthy 12 volt battery should ideally register around 12.7-12.8 volts at rest, but anywhere between 12.5-13.5 volts indicates a serviceable battery. Once a battery drops below 12.4 volts, your bike will struggle to start, and at under 11.8 volts, 12 volt batteries are considered to be dead.

Can you push start a motorcycle with a car?

Push starting your motorcycle is a great option, but sometimes if the battery is dead enough, even a push start won’t be able to get it to turn over and you’ll need to resort to using other vehicles to help you get your motorcycle started again. So, can you jump start a motorcycle with a car? It is possible to jump start a motorcycle with a car.

Why is my push starter not working on my motorcycle?

Also, if the push starter was getting an electrical current and still not working, it would have drained your battery after about 10 tries with no engine turn over. So you most likely just need to replace the push starter.

Why does my bike not start when I Turn on the ignition?

If okay, check that the switch is getting power from the ignition switch when the ignition switch is turned on. If not, your ignition switch may be faulty at the lead that supplies power to the starter switch and is probably the culprit because we know the ignition circuit works – it’s the starter circuit in question.

What happens when a motorcycle battery is dead?

If your battery is completely dead, you motorcycle will not make any noise at all when you try to start it. How a motorcycle battery dies: If a motorcycle battery is not used and just sits, it will lose it’s capacity to power your motorcycle. There is also a phenomenon called parasitic drain.

I {Heart} Hookers. I turned the bike off for 10 minutes, went back to start and only got a little short rapid clicking sound, but no turnover at all. That clicking shortly turned in to nothing after a few more tries. Going for the easy fix since I was in a parking lot at 100 degrees I put a new battery in, still nothing. The fuel pump does come on.

Why does my Dyna FXDC bike not start?

Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing. Not even a click or a buzz. Bike has been sitting for about 2 weeks.

Can a cold engine start a Harley Davidson?

After waiting say 15 or 20 minutes, it starts fine. It doesnt do this all the time and never when I first start with a cold engine. Only after I have been riding awhile sometimes it will start right away but seems after the 4th or 5th stop nothing, it just cranks like it not getting any gas or not firing.

What kind of bike won’t turnover or start?

I took a 9 mile ride yesterday on my 06 electra glide standard, everything was fine. I turned the bike off for 10 minutes, went back to start and only got a little short rapid clicking sound, but no turnover at all. That clicking shortly turned in to nothing after a few more tries.

Is the Harley Davidson Nightster a Sportster or a Nightster?

Initially, the market thought that since Sportster sales were at a low, Harley-Davidson merely painted one of their bikes black and called it the Nightster. But once experts reviewed it, they found it to be a very different motorcycle, in a good way.

Why are there no pillion seats on a Harley Davidson Nightster?

Many riders also said that the front and the rear brakes of the motorcycle needed a harder-than-usual grip to kick into proper place, but this was less a defect and more of something you needed to get used to. The Nightster also did not come with a pillion seat, so there was that issue as well with added expense if you truly wanted one.

Which is the current model of Harley Davidson Sportster?

The current Sportster models are the Iron 883 and the well-respected Iron 1200, as well as the Roadster, the SuperLow, and the Forty Eights. But in 2007, the most notable model in the Sportster line was the Nightster.

What does it mean when your motorcycle won’t start?

Not every rider uses their kill switch with regularity, but if you have used it recently, it’s possible the engine cutoff switch is still activated. Either that or someone else flicked it, or you did it by accident—either way, it’s worth a quick glimpse, as the switch remaining in the on position will prevent the motorcycle from starting.

How do you turn off the ignition on a Harley Davidson?

Turn the ignition switch on-off-on-off-on quickly. With a proximity fob system, press the left turn signal switch three times and the right turn signal switch once. The blinkers will flash and the PIN should appear in the odometer window.

I have a 2014 Street Glide Special with about 40k miles. I replace the main battery in February and then last week I took the bike for a ride. After stopping for a drink, the bike would not start.

How to turn off the FOB on a Harley Davidson?

Here’s how to do it!! 1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual. 2. With an assigned FOB present, turn IGN key ON – OFF – ON – OFF – ON 3. Press Left turn signal switch 2 times. 4. Press Right turn signal switch one time and release.

What are the diagnostic codes for Tri Glide reverse system?

Much testing can be completed with, only, a test light and a multimeter. However, a factory Tri Glide supplement manual and a breakout box is also necessary for complete diagnostic testing. There are four DTC’s that can arise for reverse failure. These codes are #s P1775 – ECM detects an error within the reverse system (this one is rather vague!)

Do you need a breakout box for Tri Glide?

Why is the battery draining on my Harley Davidson?

My battery was completely drained so I recharged the battery and when I go to put it back in as soon as I went to hook-up the negative terminal you can hear the fuel injection kick on…with the key off! Im sure this is what is draining the battery and I think it is probably a faulty ignition switch.

How many times has a Harley Davidson battery been replaced?

I turned the ignition back off, removed the key and the alarm set properly with key light flashing. Charged the battery up before taking it back to the dealers. This has happened 3 times before – the first time, the battery was replaced even though this wasn’t faulty.

Is there a problem with my Harley Davidson?

Help….. Bike is currently at Dealers for the 4th time with same problem. After riding it home from a service the day before, putting her away in the garage, turning the ignition off and leaving her for the night, I returned to ride her the next day. The engine was cold, with the ignition in the ‘off’ position, as I’d left her.

Why is my Harley Davidson Sportster not charging?

If a new battery fixes your problem, confirm the charging system is working properly by performing the same test with the engine running. A normal reading is near 14 volts. If you find a different value, move to Step 6. Even if your battery’s charge level is normal, it may not have the capacity under load to supply enough amperage.

Why is my petcock on my motorcycle not working?

The line between the petcock and the engine can sustain damage, too, which keeps the system from operating properly. With leaks—whether from cracking, rot, or road damage—you might be able to reseal the line, or you may need a replacement before you’re road-worthy again.

Why does my bike not start with a side stand down?

With leaks—whether from cracking, rot, or road damage—you might be able to reseal the line, or you may need a replacement before you’re road-worthy again. Newer bikes (and some older ones) may refuse to start with the side stand down.

What happens when you push the start button on a bike?

When you push the button it gives power to the starter to crank the motor. When you push start the bike, with it in gear you crank the motor manually, so check the connection (s) at or around the start button. As for the clutch hmmm does it engage, as in when you pull in the lever does it work as intended?

What does it mean when your bike won’t start?

Has fuel, battery was enough to turn starter which usually means there’s enough to fire the ignition if bump-started, spark plug lead is firmly connected, compression seems to exist from the rhythm of the starter and how the rear wheel locked if bumped on the slightly loose surface outside the garage in too low a gear…

What does it mean if your Harley won’t start?

If that test was a “pass”, it would eliminate with 100% certainty, the starter and starter solenoid from the picture and all the associated wiring, all the way back to the fuse box. It would demonstrate that all the heavy starter grounds were OK also. Passing just that one simple test would eliminate a dozen possible items it could have been.

your bike will not start because you have no IGNITION power. the ignition power runs the starter relay, coil and ignition module. the power source for lights and ignition are 2 separate switch contacts.

Why are my lights not working on my Harley?

What to do if your Harley Davidson voltage regulator is not working?

You can troubleshoot the issue in your garage and find a solution to the problem without visiting a repair shop. If your Harley Davidson voltage regulator problems are giving you some tough times, this article will guide you through diagnosing the issue while suggesting solutions to fix it. What’s the Possible Reason to Face This Problem?

Are there any problems with the new Harley Davidson?

This is one Harley to avoid. Yes, it’s a new bike, but the Livewire has had numerous problems in its short on again off again life. The electric bike has experienced problems with its charging system, which in turn led Harley to stop production of the bike in October of 2019.

When does the new Harley Davidson electric bike come out?

The electric bike has experienced problems with its charging system, which in turn led Harley to stop production of the bike in October of 2019. The bike only started shipping in September of 2019. Harley-Davidson has started production again, saying the bike is safe, coming out with a rather vaguely-worded statement according to The Verge.

How to get a long-stored Harley running again?

“IMO – 1st change the oil and filter as described above. Put a new AGM battery in it, drain the old gas by removing the rubber hose on the front of the tanks tank to tank. Refill with new gas and turn the key on. Listen for the fuel pump to start and stop, turn key off, and repeat. This time crank it up and let her idle a while.

Is it time to start a new Harley Davidson?

But despite what you might think, it’s not a good idea to jump on your dusty ride and immediately try to crank it up. This is especially true of any Harley that’s been sitting for more than a few months. A few years? You’ll want to do a little preventative maintenance first.

What to do about a clattering Harley Davidson?

Use at your own discretion. Remove the seat. Remove the tank bolts. Remove the console and disconnect the wiring, then set aside. Lift the tank enough to remove the rocker covers. Remove rocker arms and the hold down bolts. Inspect the rocker shafts. At the end of the rocker shafts, add a thin film of Blue Loctite 609 or 620. Button her back up.

Why does my starter click when the key is turned on?

Hope this helps!!! Nope it’s not a dead battery the starter sounds like it wants to go but all it does is click. it almost sounds like what my old s10 did when the starter is over heated. what does a starter go for?

Why does my 2002 Ford F150 not start?

Engine cranks but won’t start. 2002 Ford F150 ford 2002 Occasionally engine cranks but won’t start. Getting worse. I had fuel pump relay checked and it was good. Purchased a new one anyway. Checked fuel pressure once it started. It was 32 psi. Lost less than 5% when shut off. Replaced fuel pump.

How can you tell if a Harley Davidson starter is working?

What to do if your Harley Davidson won’t start?

Harley Davidson Sportster: Why Won’t My Bike Start? 1 Test your starter. Refer to Step 4 of the article Electrical Diagnostic Guide for information on starter testing. 2 Check for fuel. If your bike cranks but doesn’t start, the first thing to check is the fuel supply. 3 Check for spark.

Why does my bike not start when I push the starter button?

Pressing the button sends power to the starter solenoid, which sends a large amount of current from the battery to the starter to turn the motor. If the engine doesn’t crank, it could be because of a failure at any of those stages, a weak battery, or a bad starter.

Why does my bike click when trying to start?

SOLVED: Clicks when trying to start does not engage. – Harley-Davidson Sportster Evolution – iFixit Clicks when trying to start does not engage. I have a Harley-Davidson 1999 sportster 1200. I get a hard fast clicking sound when trying to start. I Have put the battery on a charger and let it charge overnight. It still does the same thing.

How does a Harley Davidson XL1200 Sportster feel?

It’s like an unintentional speed-limiter, where above 70mph the footpegs vibrate, the wind tries to lift your boots from the widely-spaced pegs (unless you hook them forward of the gear/brake pedals), and in clinging onto the wide ’bars you feel like a human parachute.

Are there any problems with a Harley Davidson?

Let’s be up front, Harley Davidson bikes aren’t known to be the most reliable or durable among the riding community. Despite that, there are enough Harley riders that most problems are well-documented with easy enough solutions. One of the main issues that plagues Harley owners have to do with the voltage regulator.

What does it take to start a Harley Davidson Sportster?

This article applies to the Harley Davidson Sportster. What does it take to start a Sportster? When you turn the ignition switch to the on position, current is sent to the start button. Pressing the button sends power to the starter solenoid, which sends a large amount of current from the battery to the starter to turn the motor.

When did the Harley Davidson 1200 Custom come out?

The 1200 Custom has been in the Sportster lineup since 1996, but it’s changed with the times—mostly. Harley-Davidson The Harley-Davidson Sportster 1200 Custom is one of those classics that’s been a staple in Milwaukee’s lineup since 1996, but for whatever reason we hadn’t had a chance to ride in 1,200cc engine form.

What kind of engine does a Harley Davidson Sportster 1200 have?

The latest incarnation of the Custom throws out a fairly thick front end with a 130mm front tire and 39mm fork to accompany the tried-and-true 1,202cc, air-cooled, overhead-valve Evolution engine, which put out 57.8 hp and 66.8 pound-feet of torque on our dyno last year.

Can you start a Harley Davidson HD without a fob?

Starting your HD without a Fob! Your HD has the ability to be started without a Fob present jus in case the Fob is lost or the battery goes dead! Your Pin# to over-ride the security system is usually loaded up with the last 5 numbers of your Harley’s serial # backwards! (EX: serial # last 5 is 1 2 3 4 5……….it was entered as 5 4 3 2 1).

Is the factory security system on a Harley Davidson?

Does the bike have the factory security system. Do the flashes start to blink on/off when you try to start it. It the answer is “No” to both questions perform this test. 1) Place Bike in NEUTRAL. 2) Remove the fuse cover and locate the start Relay.

What to do when you press the starter button on a V twin?

You can jumper a wire from your battery positive post or the battery post on your starter to your green wire solenoid connection to see if the starter activates (make sure your in neutral and the ignition is shut off). If it does starter is ok and suspect the bad relay.

What happens when you press the starter button?

Battery is almost fully charged , what I had expected after 4 months of sitting. Also, press starter button with lights pointed on wall nearby no dimming of lights at all. Otherwords no load being put on battery. Will go play with it when it warms up a bit.

Why is my gas gauge not working at high fuel level?

Some systems are wired so that high fuel level contacts the low-resistance section, gradually increasing resistance as fuel level drops. The system thus outputs higher voltage at high fuel level, gradually dropping voltage as fuel level drops.

Why does my bike not start after load test?

Thought I had a bad starter, but after the load test, determined that the battery was bad. Great example, and even then, it could also have been the cables, with excessive corrosion or a loose connection causing resistance in the circuit to shoot to a point where not enough amperage was avaialble to engage the solenoid and crank the motor.

Why is my Harley Davidson Sportster not starting?

Place your Sportster in second or third gear for the best results. A battery that can’t start your engine may no longer be recharging properly because of its age and current state of charge. The ground cables that connect the battery to your Sportster frame must also be undamaged and free of corrosion.

How often do you ride a Sportster 1200?

I own a 2007 sportster 1200. I ride this bike often, several times a week. Recently I went on vacation and the motorcycle sat for 10 days. At the same time the weather cooled down significantly while we were away.

What does it mean when a motorcycle won’t start?

At the same time the weather cooled down significantly while we were away. When I came back I put in the key the lights and odometer came on but the motorcycle didn’t have enough juice to start. It tried to turn over and ultimately just died. The lights went off, the odometer turned off, no power.

What to do if your motorcycle won’t start?

It appears the turn signal and stalls or cranks but will not start. Try removing the ecm and security fuses, wait ten minutes and reinstall the fuses. This “reboots” the turn signal module and the motorcycle will then start from that point on. The historic codes will remain for 50 starts or until cleared.

Why does my new Harley Davidson not start?

Newer model Harley’s have a safety switch to prevent the bike from being started in gear without the clutch pulled in. Be sure your bike is either in neutral or, if in gear, the clutch is pulled in before starting. So if you have made it this far, your bike is cranking and your fuel pump is operational, but you still have no ignition.

What does it mean when your Harley won’t crank?

Harley Davidson Softail will not crank refers to when the crankshaft will not turn so as to start the engine. In other words, not only will the Softail engin… Harley Davidson Softail will not crank refers to when the crankshaft will not turn so as to start the engine. In other words, not only will the Softail engin…

Navigation