How do you bypass the AC pressure switch?

I use warm water and the can upright, and add only refrigerant (though a bit of dye is ok – no sealers), the warm water raises the saturation pressure and pushes it in rapidly. The compressor will break, reed valves if lucky, connecting rod if unlucky, if you put too big a slug of liquid through it.

Is there a way to bypass the compressor?

There is a way around this problem however; you can actually bypass the compressor all together with a different serpentine belt. Locate the serpentine belt at the front of the engine. It is a rubber belt that goes over all of the accessories of the engine.

How to install an air conditioner bypass pulley?

If you still have refrigerant in your lines goto your local auto garage and get it flushed. 4 bolts to remove the A/C compressor and you’ll need to remove the hose from the back of the unit (which I believe was 2 bolts) . Once it’s out install the bypass pulley with the supplied bolts and reinstall belt.

Which is the best a / C compressor bypass pulley?

A/C Bypass Pulley 5 out of 5 stars. Read reviews for Dorman HELP! A/C Bypass Pulley When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures. Dorman HELP! A/C Bypass Pulley ☆☆☆☆☆ No rating value for Dorman HELP! A/C Bypass Pulley

How do you install a bypass pulley on an AC compressor?

Then remove the compressor drive belt. Remove the compressor, but keep the mounting bolts. Place the bypass pulley in place of the compressor and install the bolts to the proper torque. Re-install the compressor belt and tension properly.

How to bypass the a / C compressor on a Jeep Cherokee?

I used this to bypass the A/C compressor on a 2000 Jeep Cherokee. If you still have refrigerant in your lines goto your local auto garage and get it flushed. 4 bolts to remove the A/C compressor and you’ll need to remove the hose from the back of the unit (which I believe was 2 bolts) .

How is the O’Reilly a / C bypass pulley rated?

A/C Bypass Pulley 4.5 out of 5 stars. Read reviews for Dorman HELP! A/C Bypass Pulley When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures.

How to jumper a / C pressure switch, 2carpros?

Will be charging on the low pressure side of the system, but nothing will happen until I cant get the compressor running. You can still add refrigerant into the low side and it will bring system pressures up so the clutch will engage. helpful? When the pressure increases from charging the compressor will kick on.

How can I increase the pressure on my recharge kit?

To speed up the process, warm the refrigerant can in a bowl of warm water. That will boil the liquid and increase the pressure. Swap out the water for more warm water once it cools. Repeat this process until the gauge on your recharging kit shows a pressure above 25-psi.

What should the pressure be on the low pressure switch?

Swap out the water for more warm water once it cools. Repeat this process until the gauge on your recharging kit shows a pressure above 25-psi. At that point the low pressure switch should allow the AC compressor to engage. Alldatadiy.com and Eautorepair.net are professional-grade shop manuals—period.

Why do I need a low pressure switch?

That’s because the refrigerant carries the lubrication oil throughout the system. The low pressure switch cuts off compressor specifically to prevent compressor damage due to oil starvation. Low refrigerant charge = low or no oil circulation.

Can a low pressure switch cause a compressor to go off?

Put the AC on MAX before checking the compressor. Before starting the next step of diagnosis, you should know that a low-pressure switch can create problems with the compressor clutch’s relay in some car models. The system’s computer keeps the relay grounded but it can go on and off due to the bad switch.

Navigation