Where are the fuses and relays in the engine?
The injector fuse and relay are usually located in the relay box or power distribution center in the engine compartment. Fuses are used to protect various electrical circuits while supplying power to components. They help the fuel pump, fuel injection and computer systems from suffering a short circuit.
Where is the fuse for the fuel injector located?
Blown injector circuit fuse Bad fuel injector power relay A fault in the wiring harness to the injectors So, the injector fuse and relay are usually located; in the relay box or power distribution center in the engine compartment. Fuses are used to protect various electrical circuits, while supplying power to components.
Where is the fuse for the ECU located?
Locate the fuse for the ECU using the fuse diagram on the underside of the fuse panel cover. Pull the fuse for the ECU using the fuse pullers in the fuse panel. Turn the ignition to the “On” position but don’t crank the engine (it won’t start anyway).
What are the symptoms of a faulty fuel pump relay?
1 Engine does not start. A common symptom of a faulty fuel pump relay is an engine that just refuses to start, even though the engine may still crank when the 2 Engine stalls. One of the most common symptoms of a failing fuel pump relay is an engine that suddenly stalls. 3 Loss of Power. 4 No noise from the fuel pump. …
Where is the fuel pump relay located on a car?
The fuel pump relay is an electronic component that is found on virtually all vehicles equipped with an internal combustion engine. It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by…
Where do you find the fuel pump relay?
When you shut off the ignition, it powers down the fuel pump. In most vehicles, the fuel pump relay can often be found in the fuse box in the engine bay, which is usually a long black box which contains fuel pump relay along with various other fuses and relays.
What happens if the fuel pump relay fails?
If the fuel pump relay fails, the fuel pump will receive no power and will not operate, thus it will be silent. Always start with a visual inspection first before moving on to other tests, which will be specified below.
Is the fuel pump relay controlled by the PCM?
Consequently, the fuel pump relay is usually controlled by, the ignition or powertrain control module (PCM). As a result, when switched on, the fuel pump relay; will provide current to the fuel pump, so that it may function. Therefore, any faults with it, can cause fuel pump issues.
Where to check for no start fuel pump?
The first thing you want to do is check the fuse panel to see if the fuse is blown. If your car has two fuse panels than the one in the engine compartment; should be the correct one to check. The fuse panel or circuit box is usually located near the battery; and is a small black box with a removable lid.
The injector fuse and relay are usually located in the relay box or power distribution center in the engine compartment. Fuses are used to protect various electrical circuits while supplying power to components. They help the fuel pump, fuel injection and computer systems from suffering a short circuit.
What should I do if my fuel pump is not working?
Fuel pump breakers usually have a button on top that pops up when it trips. Simply push this button back in until it clicks. Check the owner’s manual for the exact location. Fuel Pump Testing – If the fuse is good and the circuit breaker is not tripped; then the engine is not getting fuel pressure.
What should fuel pressure be when no Buzz?
Fuel pressure is typically in the 35 to 45 psi range. If your Anti-Theft light is flashing; the anti-theft system is disabling the fuel pump to prevent the engine from starting. Bad fuel pump (Pump should run for a few seconds when ignition key is turned to start, no buzz means no fuel delivery to the engine).
What should the pressure be on an electric fuel pump?
Electric fuel pumps on electronically controlled fuel injection systems need to produce enough “high” pressure to allow the injectors to produce a sufficient spray of atomized fuel into the intake path (or into the combustion chamber in a direct-injection system). Fuel pressure is typically in the 35 to 45 psi range.