How to clean idle control valve on Hyundai Getz?
Remove the clip (be careful and work slowly) and the 2 screws. Gently remove the valve. With the 2 holes in an upside down position, spray with carb cleaner. Repeat a few times, and let it dry upside down. Replace, and rev the engine a few times untill all sounds normal when idling.
Why are the tappets on my Hyundai Getz not working?
This is caused by a known issue with the tappets. Before you try to adjust the tappets, or even replace them you should change the engine oil. Using a different type of engine oil can resolve the issue. Try using a better quality oil, but if this does not sort the problem you will need the tappets adjusted, or even replaced.
What to do when your Hyundai Getz Jerks?
The car has developed a minor jerk that occurs whenever you accelerate. Any hesitation or ‘jerking’ in your car needs to be addressed. Start by checking the spark plugs and either clean or replace them and the housing unit. It’s also worth cleaning the throttle body if your spark plugs are fine.
Why does my Hyundai Getz refuse to start?
The car refuses to start, especially in the cold. You have already checked the battery and found it to be working and charged. This could be caused by a range of issues, but for any Hyundai Getz manufactured after 2010, there’s a high likelihood that it’s being caused by the alarm module.
How to clean and relearn Hyundai throttle body?
1. Remove the breather hose and air intake hose. 2. With ignition key off disconnect the ETC connector from the throttle body. 3. Remove the 4 ETC throttle body mounting bolts and then pull out the ETC throttle body away from the intake manifold.
Remove the clip (be careful and work slowly) and the 2 screws. Gently remove the valve. With the 2 holes in an upside down position, spray with carb cleaner. Repeat a few times, and let it dry upside down. Replace, and rev the engine a few times untill all sounds normal when idling.
This is caused by a known issue with the tappets. Before you try to adjust the tappets, or even replace them you should change the engine oil. Using a different type of engine oil can resolve the issue. Try using a better quality oil, but if this does not sort the problem you will need the tappets adjusted, or even replaced.
Is there a problem with my Hyundai Getz 1.3?
Actions taken so far: 1. Swap … read more Subaru and Nissan factory training. 01 Hyundai accent 1.5l with 89000, has bad hesitation and runs very rough only when engine is in a low vacume, idels rough, and hesatation is worse when the engine is cold.
Are there any problems with the Hyundai Getz?
I have an automatic Hyundai Getz 2010 and I have recently changed its timing belt, spark plugs and filters, and maintained the injectors as well. The last few days, it has been having problems to start when cold. It was only after the second or third time of trying that the engine finally started working.
Why does my Hyundai Getz make a ticking noise?
The Getz has known issues with a ticking noise coming from the engine, particularly when the engine is cold. This is caused by a known issue with the tappets. Before you try to adjust the tappets, or even replace them you should change the engine oil.
How can I raise the RPM on my Hyundai Getz?
Raise the rpm manually with the graduation screw, so that you maintain it a bit more accelerated, up to the desired revolutions. Check the wire that goes from the alternator to the battery and check that it is the same voltage the one that leaves the alternator and the one the battery receives.
I have an automatic Hyundai Getz 2010 and I have recently changed its timing belt, spark plugs and filters, and maintained the injectors as well. The last few days, it has been having problems to start when cold. It was only after the second or third time of trying that the engine finally started working.
The Getz has known issues with a ticking noise coming from the engine, particularly when the engine is cold. This is caused by a known issue with the tappets. Before you try to adjust the tappets, or even replace them you should change the engine oil.
Raise the rpm manually with the graduation screw, so that you maintain it a bit more accelerated, up to the desired revolutions. Check the wire that goes from the alternator to the battery and check that it is the same voltage the one that leaves the alternator and the one the battery receives.