Where is the OBD connector on a Hyundai Accent?

OBD connector location for Hyundai Accent (2000 – 2005) You will find below several pictures which will help you find your OBD connector in your car. OBD Connector is located to the bottom left of the steering wheel. Go to the OBD2. scanner for HYUNDAI. OBD Connector is near the fog light button.

Where are the components in a Hyundai Accent?

Components and Components Location Components 1. Shift lever knob 2. Shift lever assembly 3. Control cable 4. Shift lock cable assembly 5. Retainer 6. Brake pedal assembly Push the cruise ON/OFF button (the CRUISE indicator light in the instrument cluster will go off). Turn the ignition off.

Where are the connectors on a Hyundai engine?

Hyundai Engines – Please select the connector for your vehicle from the options below. Locations: Under the drivers side dash panel. Under the passengers side dash panel. Under the drivers side kick panel. Under the passengers side kick panel. Locations: In or next to the fusebox under the dash panel.

What is the pinout for Hyundai OBD II?

This pinout is associated with 24 compatible devices or models. Show them> Note that list is not 100% complete! * ’08 iLoad manual has VSS at pin 3. Some OBD-II cables schemes:

Where do I find the fault code on my Hyundai?

Connect your OBD-II scanner into the OBD-2 port under the dashboard on the driver’s side. Note: Even a $20 generic OBD-2 scanner can retrieve check engine / ECU Hyundai fault codes. Those are P-codes in the Hyundai list below.

What is in the fuse box on a Hyundai Accent?

Instrument cluster, Courtesy lamp, Trunk room lamp, ETACM, DLC, Door warning, Multipurpose check connector ECM, A/T shift lever, Transaxle range switch, Mass air flow sensor, Vehicle speed sensor, Water sensor

What is the fault code for the Hyundai Elantra?

Hyundai Sonata, Excel 90 on , Scoupe 91 & 92 , Elantra. Hyundai Scoupe 93 through 95 and Accent vehicles. 4155 ECM failure A/C relay, IAC, PC.” You will need a Hyundai multi-system OBD-2 scanner to read Hyundai specific fault codes.

What’s the misfire code on the Hyundai Accent?

Mileage may suffer as well when your Accent has P0304 as well. P0304 is a cylinder specific misfire code, which means that Cylinder 4 is misfiring and causing the code.

Where is the cylinder 4 on a Hyundai Accent?

An important thing to understand when finding the location of Cylinder 4 is that it’s going to be the 4’th cylinder in the firing order of the vehicle, and not the 4’th cylinder that you might see when looking at the engine. The P0304 trouble code will trigger the Accent’s service engine soon light. The vehicle itself may begin to run rough.

Why does my Hyundai Accent have a p0304 code?

The engine is also not firing all of the fuel, so raw fuel is also passing through Cylinder 4 into the exhaust. Mileage may suffer as well when your Accent has P0304 as well. P0304 is a cylinder specific misfire code, which means that Cylinder 4 is misfiring and causing the code.

Where is the OBD2 port in my Hyundai?

OBD2 port Hyundai Accent (1995 – 1999) – Find your plug ! Where is my OBD2 port ? All vehicles are equipped with an OBD port to which you can connect your klavkarr diagnostic case. Sometimes, the most difficult thing is to find this port!

How to find the diagnostic connector on a Hyundai?

Hyundai has two different methods of retrieving codes for this connector, you may be able to tell which method to use by checking the terminals in the connector (terminals may only exist for one method not the other). If not, both methods may have to be tried to find the correct one. ‘Method 1’ is thought to be more common than ‘Method 2’.

What does check engine light on Hyundai Accent mean?

A check engine light can indicate a broad spectrum of problems with your 2013 Hyundai Accent. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.

Navigation