What are the brake problems on a Hyundai Tucson?
Shudder in brake pedal and steering wheel when applying brakes, on any downhill terrain, especially when cold to not fully warmed up, brake-wise. Dealer tech said they could not duplicate and did not notice condition. Replaced passenger side brake cable. Warning: the aftermarket part is not an exact fit, be sure to by OEM part.
How do you fix a leaky brake line fitting?
1. Unscrew the brake line from the fitting. 2. Clamp the appropriate-sized collet around the line. 3. Connect it to the Surseat lapping tool. 4. Spray some lubricant to the lapping head before using it. 5. Rotate the lapping head back and forth about 6-10 times.
What does it mean when your brake line is leaking?
Brake lines will leak at the flare when there is a poor connection with the seat of the fitting. This type of leak is commonly known as a weep. It is the result of a tiny imperfection in the flare that occurs while flaring the tube.
How much does it cost to repair a Hyundai Tucson?
The repair cost chart excludes repairs made under warranty, do-it-yourself repairs, and repair trips that include maintenance. 164-horsepower 2.0L I4 6-speed shiftable automatic AWD
What should I do about my Hyundai Tucson suspension problems?
Change all rubber bushings on rear and front stabilizer bar. Change of steering link rods thumping sound from of vehicle when at or above speeds of 80KM rear. replaced right rear wheal bearing.
Are there any recalls on the Hyundai Tucson?
Chart based on 486 repairs. See TSBs and recalls for the Hyundai Tucson. Worried about potential repair costs? An extended warranty can provide peace of mind. Chart based on 91 repair trips. The repair cost chart excludes repairs made under warranty, do-it-yourself repairs, and repair trips that include maintenance.
What to do if your brake master is leaking?
If the master is leaking you will be able to see brake fluid dripping from the front of the brake booster and rear of the master. If a leak is observed the brake master cylinder must be replaced. Next, use a flashlight check the backside of each tire and look for leakage which will be obvious.
Why does my Hyundai Tucson squeak while driving?
Squeaking in chassis subsection while driving, gets worse when you drive over bumps or on uneven roads, dealer claims there some area in the subsection that needed tightening. This was done, but noise returned after two days. Rattle over bumps, replace front sway bar links.
How do you Bleed the base brake system?
Bleeding brakes all Saturday afternoon isn’t that fun for you and certainly not for your wife. You’re going to need a scanner that can communicate with the ABS/TCS computer. Then select ABS/TCS Special Functions on the scanner. Then select Automated Bleed Functions from the menu.Then bleed the base brake system.
How do you Bleed brake fluid in a Hyundai?
Connect a clear plastic tube to the wheel cylinder bleeder plug and insert the other end of the tube into a clear plastic bottle that is half filled with clean brake fluid. Connect the scan tool to the data link connector located underneath the dash panel. Select and operate according to the instructions on the scan tool screen.
What to do if your Tuscon has stability control?
If I get my brakes to a point that I at least get decent braking, take the car to a gravel road and slam on brakes to skid thereby engage the ABS, thereby pushing fluid through them. Then bleeding the brakes again. If my specs are correct, your Tuscon has stability control.
What does the brake warning light on a Hyundai Tucson mean?
Your Hyundai Tucson ‘s brake light indicator is there to let you know that there is an issue with the brake system. It is different than the anti-lock brake system, which gets its own ABS warning light. The brake light indicates that there is a problem with the physical braking system itself.
What to do if your Hyundai Tucson is having trouble stopping?
If your Tucson is having trouble stopping, or noticeably leaking fluid, don’t drive it. Just have it towed to a mechanic. If you mess up fixing your engine, the vehicle does not move. If you mess up fixing the brakes, it doesn’t stop.
Connect a clear plastic tube to the wheel cylinder bleeder plug and insert the other end of the tube into a clear plastic bottle that is half filled with clean brake fluid. Connect the scan tool to the data link connector located underneath the dash panel. Select and operate according to the instructions on the scan tool screen.
Bleeding brakes all Saturday afternoon isn’t that fun for you and certainly not for your wife. You’re going to need a scanner that can communicate with the ABS/TCS computer. Then select ABS/TCS Special Functions on the scanner. Then select Automated Bleed Functions from the menu.Then bleed the base brake system.