Why does my Car start but no spark?
If the problem is no spark, anything in the ignition circuit that creates the spark may be at fault. Use your AutoTap Express DIY to look for an RPM signal from the Crankshaft Position sensor while cranking the engine. A bad Crankshaft Position sensor is a common cause of no starts.
How long does it take for accent spark to get to 60kph?
I replaced the coil pack, and it is still the same weak spark that misses and loses power above 2K revs when plugs gapped to 1mm, takes about 30 seconds go get to 60KPH.
Why does my Hyundai Accent car not start?
I see this as a manufacturing fault with the electrical system and Hyundai should take care of this major safety issue at no cost to the consumer. The contact owns a 2013 Hyundai Accent. The contact stated that the vehicle failed to start without warning. The failure occurred on several occasions.
Why is the spark not showing at the plug?
To give that plug body to ground arc means that there is plenty of power in the coil packs, stacks of it in fact but why is that not showing as a strong spark at the plug. Bosche or NGK behaved the same.
How to know if your engine has no spark?
First Confirm Your Engine Has No Spark. 1 Disable the fuel system by removing the fuel pump fuse or relay. 2 Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. 3 Finally, Have someone crank the engine and watch for spark.
Why does my car have a no spark light?
In this case you most likely have a failed ignition coil. That would explain why you have injector pulse and no spark. If the light does not flash, you still have a problem with both injector pulse and spark, suspect a problem with the ECM (engine control module).
What causes a car to stall with no spark?
Consequently, An old or failing ignition pickup may cut out signal intermittently, which may cause the engine to stall. The engine may suddenly just shut off, almost as if the key had been turned off. Depending on the nature of the issue, sometimes the vehicle can be restarted and driven.
What do I need to know if my car wont start?
I found the problem. you must have a late production date 2000 as the wire colors match for the 2001 year model. See if you have power to the orange wire to both coils, then see if your test light will flash if you probe the blue, and brown wires with the engine turning over please.
What to do when your car cranks but won’t start?
If the coil is sparking and the rotor turning, check ignition timing. If there’s no spark, check the points or ignition module. If the rotor isn’t turning, the distributor shaft has most likely snapped and you need to replace the distributor. Check the condition of the distributor cap. Is the underside of the cap wet?
What to do when your engine has no spark?
Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. Finally, Have someone crank the engine and watch for spark. Remove one of the coils from the spark plug. Use an extra spark plug. A spark plug tester. Or even a screwdriver in the end of the coil.
Why does my Nissan club have no spark?
It has no spark, the tack does not move. We changed the crank sensor, and no change. My scanner said that it should have 5 vdc on one pin of the connector and that the sensor should ohm out at 165 to 200 ohms. When I tested the plug I had 12 vdc and the sensor reads open across all the pins. Did you rebuild the motor? did it die when driving.
Why does my car not start when I crank the engine?
The crankshaft position (CKP) sensor monitors the position or rotational speed of the crankshaft. If the crankshaft position sensor has failed completely, and isn’t sending a signal to the (ECU) at all, then the computer won’t send any fuel to the injectors. This will leave you unable to start the car.
Why is the crank sensor on my car not working?
This is because the crankshaft position sensor gives the signal for both fuel and spark, and it is very common for this sensor to fail on this vehicle. First, check the wiring and connector to the crank sensor. If that is ok, replace the sensor: