Can you change transmission fluid in a Hyundai Tiburon?
Changing fluids in your vehicle is a simple procedure that can help save you time and money. The Hyundai Tiburon features both manual and automatic transmission models. Each has different fluid requirements and a different method of refilling, but you can add transmission fluid to both with a minimal amount of time and effort.
What’s the best way to drive a Tiburon?
Drive your Tiburon about 15 to 20 miles on an expressway, or the equivalent distance in city driving, to achieve normal engine operating temperatures. Park the car on a level surface, with the engine idling and the emergency brake applied. Shift the gear selector through each of the gear positions, including reverse.
How do you clean the bottom of a transmission pan?
Use the socket wrench to remove the filter-retaining bolts, and remove the filter. Clean the bottom pan with a noncombustible solvent. You might need to scrape the remaining pieces of the old gasket off the pan with a razor blade. Also, clean the gasket surface of the transmission.
What to do if your transmission fluid runs out?
Find the transmission fluid filler hole on the driver’s side of the transmission. Remove the filler plug. If lubricant runs out, or you can feel lubricant inside the reservoir with your little finger, the transmission fluid is at the proper level. Otherwise, proceed to Step 3.
Where is the transmission fluid in a car?
It is at the rear of the engine compartment, on the passenger side. Wipe it clean with a paper towel. Replace the dipstick, making sure it seats completely, before removing it again. The fluid level should be between the “Add” and “Full” lines. If not, fill with transmission fluid as indicated in your owner’s manual.
Changing fluids in your vehicle is a simple procedure that can help save you time and money. The Hyundai Tiburon features both manual and automatic transmission models. Each has different fluid requirements and a different method of refilling, but you can add transmission fluid to both with a minimal amount of time and effort.
Find the transmission fluid filler hole on the driver’s side of the transmission. Remove the filler plug. If lubricant runs out, or you can feel lubricant inside the reservoir with your little finger, the transmission fluid is at the proper level. Otherwise, proceed to Step 3.
It is at the rear of the engine compartment, on the passenger side. Wipe it clean with a paper towel. Replace the dipstick, making sure it seats completely, before removing it again. The fluid level should be between the “Add” and “Full” lines. If not, fill with transmission fluid as indicated in your owner’s manual.
Drive your Tiburon about 15 to 20 miles on an expressway, or the equivalent distance in city driving, to achieve normal engine operating temperatures. Park the car on a level surface, with the engine idling and the emergency brake applied. Shift the gear selector through each of the gear positions, including reverse.
What to do when transmission fluid comes out of drain?
Remove the drain plug and allow the transmission fluid to empty into the drain pan. It will initially come out with some force, so be ready to adjust the placement of the drain pan as the fluid drains. Fill the transmission to the filler hole with the appropriate lubricant (either SAE 75-85W or 85W-90 gear oil). Replace the filler plug.
What kind of lubricant to fill transmission filler hole?
Fill the transmission to the filler hole with the appropriate lubricant (either SAE 75-85W or 85W-90 gear oil). Replace the filler plug. Empty your transmission fluid when it is at normal operating temperature. The higher temperature will help flush out any particles with the old fluid.
What kind of transmission fluid do I Need?
Pour 4 quarts of Mopar ATF Plus Type 7176 automatic transmission fluid down the filler tube. Start the engine, with the transmission in “Park.” Allow the car to idle for a few minutes, then shift the gear selector through all the gears. Check the transmission fluid level, and adjust as needed.
Remove the drain plug and allow the transmission fluid to empty into the drain pan. It will initially come out with some force, so be ready to adjust the placement of the drain pan as the fluid drains. Fill the transmission to the filler hole with the appropriate lubricant (either SAE 75-85W or 85W-90 gear oil). Replace the filler plug.
Fill the transmission to the filler hole with the appropriate lubricant (either SAE 75-85W or 85W-90 gear oil). Replace the filler plug. Empty your transmission fluid when it is at normal operating temperature. The higher temperature will help flush out any particles with the old fluid.