What does the p0133 code on my car mean?

What does the p0133 code on my car mean?

What Does the Code P0133 Mean? The code P0133 indicates your vehicle’s oxygen sensor is having a problem. This sensor monitors how much oxygen comes out of the engine and transmits this information to your vehicle’s computer.

How much does it cost to replace a p0133 Ford sensor?

Replacing the Front Heated Oxygen Sensor Bank 1 usually takes care of the problem. What does this mean? The cost of diagnosing the P0133 FORD code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

When to take care of a p0133 problem?

While a P0133 code does not typically point to problems that seriously compromise safety or driveability, it is important to take care of these issues promptly. Even when the problem is fairly minor, addressing it quickly prevents it from snowballing and beginning to affect other components.

What is the problem code for the O2 sensor?

P0133 – O2 Sensor Circuit Slow Response (Bank 1 Sensor 1) P0156 – O2 Sensor Circuit Slow Response (Bank 2 Sensor 2) P0411 – Secondary Air Injection System Incorrect Flow Detected Thanks for …

What does the OBD code p0133 mean?

What does code P0133 mean? OBD-II Code P0133 is defined as an Oxygen Sensor Circuit Slow Response (Bank 1, Sensor 1) Code P0133 is triggered when the powertrain control module or PCM determines that the oxygen sensor voltage switch from below 400 millivolts to above 450 millivolts is taking too long.

Replacing the Front Heated Oxygen Sensor Bank 1 usually takes care of the problem. What does this mean? The cost of diagnosing the P0133 FORD code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

What is the error code for oxygen sensor?

Error Code P0133 is described as Oxygen Sensor Circuit Slow Response (Bank 1, Sensor 1).

What to do when the freeze frame code is p0133?

When the code P0133 is set, record the freeze frame data in fine detail. Next, duplicate the code setting conditions on a test drive, paying particular attention to load, MPH, and RPM. The best tool to use on this test drive is a data streaming scan tool that has factory quality, dedicated live data.

What causes a p0030 code on a HO2 sensor?

Potential causes of a P0030 trouble code may include: Failed or damaged heater circuit element inside the HO2S Open on the O2 sensor heater’s ground circuit Open or short on O2 sensor heater’s B+ battery feed (on some vehicles this may be the control circuit) Many times a HO2 sensors heater element may go bad due to age or impact.

What should I do if I get error code p0340?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: ZaIxO1juVG_c4myN) Videos you watch may be added to the TV’s watch history and influence TV recommendations.

What causes an EGR code to be misfired?

Defective DPFE sensor in the EGR system causing EGR codes are often occurs on Ford vehicles. Misfire codes P0171 or P0174 indicated the engine too much air and/or engine is not enough fuel (fuel mixture running lean).

What Does the Code P0133 Mean? The code P0133 indicates your vehicle’s oxygen sensor is having a problem. This sensor monitors how much oxygen comes out of the engine and transmits this information to your vehicle’s computer.

When do I get a camshaft sensor code p0341?

Code P0341 is triggered when the camshaft sensor does not correlate to the position of the crankshaft. The crankshaft sensor should also be checked during the diagnostic checks for any problems that could cause the code to be received.

What does the p0341 OBD-II trouble code mean?

What the P0341 code means P0341 is an OBD-II generic code that says the engine control module (ECM) detected the engine camshaft position sensor circuit is not within specifications. The sensor pulses do not correlate to the pulses of the crankshaft sensor. What causes the P0341 code?

While a P0133 code does not typically point to problems that seriously compromise safety or driveability, it is important to take care of these issues promptly. Even when the problem is fairly minor, addressing it quickly prevents it from snowballing and beginning to affect other components.

What happens when you get a trouble code p0341?

A P0341 trouble code will generally trigger the check engine light on. Depending on your vehicle’s make, the check engine light may be referred to as the CEL, the Malfunction Indicator Lamp (MIL) or Service Engine Soon (SES) light.

P0133 – O2 Sensor Circuit Slow Response (Bank 1 Sensor 1) P0156 – O2 Sensor Circuit Slow Response (Bank 2 Sensor 2) P0411 – Secondary Air Injection System Incorrect Flow Detected Thanks for