What does the OBD code B1352 stand for?
OBD II fault code B1352 is a manufacturer specific code that is defined by carmakers Ford and Jaguar as “Ignition key-in – circuit failure”, and is set when the PCM (Powertrain Control Module) detects a malfunction or general failure in circuits that are active when the ignition is switched off,…
How long does it take to diagnose Ford B1352 code?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the B1352 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
How much does it cost to repair a B1352 Ford?
The cost to diagnose the B1352 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
OBD II fault code B1352 is a manufacturer specific code that is defined by carmakers Ford and Jaguar as “Ignition key-in – circuit failure”, and is set when the PCM (Powertrain Control Module) detects a malfunction or general failure in circuits that are active when the ignition is switched off,…
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the B1352 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
Do you need scanner to read airbag trouble codes?
Working with your airbag system is crucial, and therefore, always read the trouble codes with an OBD2 scanner to get an idea of where to start your troubleshooting. Do never clear the trouble codes before you fix the problem caused by the airbag light.
Do you clear trouble codes before resetting airbag light?
Do never clear the trouble codes before you fix the problem caused by the airbag light. Read the codes and get information about what can cause the problem and therefore continue the diagnosis. You should never just reset the airbag light without repairing the problem.
Where does the P0420 trouble code come from?
P0420 is triggered in the engine control module when there is a problem with the efficiency of the catalytic converter. The engine control unit uses two O2 sensors, one in the front of and one behind the catalytic converter to measure the efficiency of the catalytic converter.
Can a damaged catalytic converter trigger the code po420?
Yes, they can, but not in the way you think. Rich or lean mixtures can damage the catalytic converter, and when the catalytic converter is damaged/filled with fuel, the efficiency will be low, and the rear O2 sensor will see that and show the trigger the code Po420.
What are the causes of a p1352 code?
P1352 Possible Causes 1 Faulty Ignition Control Module 2 Ignition Control Module harness is open or shorted 3 Ignition Control Module circuit poor electrical connection
How much does it cost to repair a p1352 code?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P1352 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.
What is the OBD code for ignition key in circuit failure?
OBD II fault code B1352 is a manufacturer specific code that is defined by carmakers Ford and Jaguar as “Ignition key-in – circuit failure”, and is set when the PCM (Powertrain Control Module) detects a malfunction or general failure in circuits that are active when the ignition is switched off, but while the key is still in the ignition.
Can a soft ignition switch be connected to OBD?
This can be easily done in the OBD stream. If you want anything more than that you need manufacturer specific and then not everyone is going to support it. If a car has a soft ignition switch then it is connected to some module that reads it’s position and turns on relays to power up the car.
What is the OBD2 code for engine performance?
OBD-II Code Decreased engine performance is defined as a Cylinder 8 Deactivation/Intake Valve Control Circuit Performance In an effort to meet fuel and emissions standards, many manufacturers are utilizing cylinder deactivation systems.
How much does it cost to diagnose a Ford code B1359?
The cost to diagnose the B1359 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars?
OBD II fault code B1352 is a manufacturer specific code that is defined by carmakers Ford and Jaguar as “Ignition key-in – circuit failure”, and is set when the PCM (Powertrain Control Module) detects a malfunction or general failure in circuits that are active when the ignition is switched off, but while the key is still in the ignition.
What does run / ACC mean on Ford B1359?
B1359 FORD Meaning The Ignition Switch RUN/ACC circuit provides voltage through the circuits to the Smart Junction Box (SJB) when the key is in the RUN/ACC position. The OBDII sets when the Ignition Switch signal is not factory specifications.