What does trouble code p0335 mean on Hyundai Santa Fe?
The Hyundai Santa Fe utilizes a crankshaft position sensor in order to regulate the engine timing. This sensor uses a reluctor to gauge the position of the crank. When the Santa Fe’s ECM determines that there is an issue with the signal coming from this sensor, it’ll throw the P0335 trouble code.
What kind of engine does the Hyundai Sonata have?
NF Sonata was launched in August 2004 in Korea on the basis of a new platform created from the NF project. The first all-aluminum engine I4, called Theta, made its debut in the new Sonata. The choice of engine at startup was 2. 4-liter I4 with a power of 164 hp. (122 kW) at 5800 rpm and 3. 3-liter V6 with a power of 237 hp. (177 kW) V6.
Are there any problems with the Hyundai 2.4 engine?
Hyundai and KIA car owners with the 2.4 engine cited various problems including the timing chain. Check out what some owners had to say! “My 08 Sonata with the 2.4L engine was towed to the dealership.
Is there a Repair Manual for the Hyundai Sonata?
Hyundai Sonata PDF Workshop, Service and Repair manuals, Wiring Diagrams, Parts Catalogue, Fault codes free download!! Hyundai Sonata – front-wheel drive sedan.
The Hyundai Santa Fe utilizes a crankshaft position sensor in order to regulate the engine timing. This sensor uses a reluctor to gauge the position of the crank. When the Santa Fe’s ECM determines that there is an issue with the signal coming from this sensor, it’ll throw the P0335 trouble code.
How much does it cost to repair a p0335 Hyundai engine?
Cost of diagnosing the P0335 HYUNDAI code Labor: 1.0 The cost of diagnosing the P0335 HYUNDAI code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0335 HYUNDAI code detected?
What does the p0335 crankshaft position sensor code mean?
Sometimes and in some models, low battery voltage or a weak starter can trigger a Crankshaft Position Sensor code. Before replacing any parts, recharge or replaced battery. 2004 Hyundai Sonata V6 2.7 crankshaft position sensor location and replacement codes P0335 and P1372 User Submitted Video What does this mean?
What is the crankshaft position sensor in a Hyundai?
P0335 Hyundai Description The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. This information is used by the Electronic Control Module(ECM) to control ignition and fuel injection.
Sometimes and in some models, low battery voltage or a weak starter can trigger a Crankshaft Position Sensor code. Before replacing any parts, recharge or replaced battery. 2004 Hyundai Sonata V6 2.7 crankshaft position sensor location and replacement codes P0335 and P1372 User Submitted Video What does this mean?
How does the crankshaft position sensor work on a Santa Fe?
The Hyundai Santa Fe utilizes a crankshaft position sensor in order to regulate the engine timing. This sensor uses a reluctor to gauge the position of the crank.
Cost of diagnosing the P0335 HYUNDAI code Labor: 1.0 The cost of diagnosing the P0335 HYUNDAI code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0335 HYUNDAI code detected?
The Hyundai Santa Fe utilizes a crankshaft position sensor in order to regulate the engine timing. This sensor uses a reluctor to gauge the position of the crank.
Why is the p0335 thrown on the road?
The crankshaft sensor is often the reason that P0335 is thrown. They aren’t very expensive, but they can be difficult to get to in order to service them. If you think you’re up to the challenge (and know how to use a volt meter) this guide from doityourself.com will show you exactly how to test the sensor.
When does the ECM set the trouble code p0335?
It works hand in hand with the reluctor ring that creates a square wave voltage signal that the ECM interprets as the crankshaft position. Trouble code P0335 is set whenever the ECM does not sense crankshaft pulses or senses a problem with the pulses in the output with Sensor “A” Bank 1.
It works hand in hand with the reluctor ring that creates a square wave voltage signal that the ECM interprets as the crankshaft position. Trouble code P0335 is set whenever the ECM does not sense crankshaft pulses or senses a problem with the pulses in the output with Sensor “A” Bank 1.
Can a p0455 code cause a Santa Fe to stop running?
While P0455 is not going to cause the Santa Fe’s engine to stop running, it should not be treated lightly. You could have a fuel leak. Pay extra attention to your tank level and make sure you are not leaking fuel. We recommend taking it in and/or dealing with it right away.
What is the trouble code on my Hyundai Santa Fe?
One of the most common trouble codes with the Hyundai Santa Fe is the P0455 code. This trouble code references a number that is given to you when you plug your Santa Fe into a OBDII scanner. P0455 Indicates that there is a large leak in the evaporative emission control system.
What are the problems with the 2009 Hyundai Santa Fe?
Table 1. Common problems of the 2009 Hyundai Santa Fe Problem Category Number of Problems Other Fuel System 115 Engine And Engine Cooling 50 Service Brakes 44 Electrical System 43
How much does it cost to repair a p1690 Hyundai?
The cost of diagnosing the P1690 HYUNDAI code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
Why does my Santa Fe y2006 not start?
Hello, my Santa Fe Y2006 has this same problem. New glow plugs, currently changed crankshaft position sensor, battery in good condition, starter spins perfectly but no starting when cold (in the morning). Possible to start only after spraying of starting fluid directly to air filter outlet.
What is the code for the Hyundai Santa Fe?
The code in the computer after failure should be P1690 or P1693 (or both). After changing the antenna piece near the ignition (180$ at the dealer), the icon shows up and car starts every time…. been around 50 times to far and no issues. Hope this helps 75 people found this helpful. this sounds so similar to whats happening with our 02 santa fe.