What does the p0010 code on a car mean?
What Does the P0010 Code Mean? Code P0010 stands for “A” Camshaft Position Actuator Circuit (Bank 1). The code indicates that your car’s primary computer, which is also referred to as the powertrain control module (PCM), perceives a problem with one of the engine’s VVT solenoids.
What is the trouble code for a camshaft?
P0010 is a diagnostic trouble code (DTC) for “”A” Camshaft Position Actuator Circuit (Bank 1)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. Our certified mobile mechanics can come to your home or office to perform the Check Engine Light diagnostic.
What is the code for a camshaft position actuator?
P0010 Code: “A” Camshaft Position Actuator Circuit (Bank 1) – In The Garage with CarParts.com Intake/Exhaust Camshaft Actuator Solenoid test (P0010, P0011) – GM 2.4
When do I get a p0010 error on bank 1?
When the Engine Control Module tries to adjust the timing of the Bank 1 intake camshaft with one of these oil control valves, and it alerts an electrical issue with the solenoid windings in the valve or the circuit that goes into the valve, the code P0010 error is triggered.
What does the p0010 code mean on a car?
A P0010 code refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car’s PCM (powertrain control module) or ECM (engine control module). VVT is a technology used in the engine to allow it to get greater power or efficiency at different running points.
What to do if your camshaft position sensor says p0340?
Visually inspect the camshaft position sensor connector in search of corroded or broken connectors. Make any other repairs (if other codes are present) to make sure that other codes are not sources of the trouble code P0340. Check your camshaft position sensor’s voltage, ground, and signal readings with a multimeter.
What is the error code for the camshaft position actuator?
OBD check showed P0010, (camshaft position actuator circuit ) looked and found that a critter had eaten the wiring to the positioning solenoid. I repaired the wiring, but the error code remains. Circuit testing shows 12.43 volts on the connector a…
Why do I need to change the camshaft position sensor?
The problem with changing out the camshaft position sensor is that sometimes the issue is actually due to the sensor wiring harness; which might be the reason this OBD-II error code was triggered initially. The P-0340 trouble code indicates that the signal to and from the camshaft position sensor and the PCM is broken.
What does the odb2 code p0010 mean?
The ODB2 code P0010 indicates that there is likely to be an issue the timing of the mechanical variable valve in your car.
What are the symptoms of p0010 in a Chevy Equinox?
Here are some of the typical symptoms of P0010 in the Chevy Equinox: Poor Idle Quality – If the camshaft actuator fails while giving the engine aggressive valve timing, it’ll idle roughly.
What Does the P0010 Code Mean? Code P0010 stands for “A” Camshaft Position Actuator Circuit (Bank 1). The code indicates that your car’s primary computer, which is also referred to as the powertrain control module (PCM), perceives a problem with one of the engine’s VVT solenoids.
When the Engine Control Module tries to adjust the timing of the Bank 1 intake camshaft with one of these oil control valves, and it alerts an electrical issue with the solenoid windings in the valve or the circuit that goes into the valve, the code P0010 error is triggered.
The ODB2 code P0010 indicates that there is likely to be an issue the timing of the mechanical variable valve in your car.
Why do I get an error code on my ECM?
The error is detected most commonly at higher speeds as the ECM tries to adjust the valve lift to compensate for the higher RPMs. The sensors in the ECM are used to find the position of the camshafts and the crankshaft. It uses the data from these sensors to control valve lift, ignition and fuel timing as the car is running.
P0010 Code: “A” Camshaft Position Actuator Circuit (Bank 1) – In The Garage with CarParts.com Intake/Exhaust Camshaft Actuator Solenoid test (P0010, P0011) – GM 2.4