What to do if your Hyundai has a p1326 code?
Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P1326 HYUNDAI code is 1.0 hour of labor.
How much does it cost to diagnose p1326 in a car?
The cost to diagnose the P1326 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars?
Why was p1326 added to the PCM?
Fault P1326 was added the the PCM via a software update to detect engine bearing failure using the knock sensor. The system is flawed, electrical interference in the wiring can cause false alarms. An overlay wiring harness has been developed to correct the false alarms.
What should I know about the 2013 Hyundai Sonata?
2013 Hyundai Sonata Electrical Equipment TSB Details … 2013 Hyundai Sonata Electrical System Software TSB Details … 2013 Hyundai Sonata Electrical Wiring TSB Details … 2013 Hyundai Sonata Engine TSB Details … 2013 Hyundai Sonata Engine and Engine Cooling TSB Details … 2013 Hyundai Sonata Engine Control Module Software TSB Details …
What’s the p1326 code on a Hyundai Sonata?
P1326 code flashing check engine light blinking. Blinking. 2013 Hyundai sonata. Just parked it in drive way was on Hyundai repair questions? Ask a mechanic for answers ASAP By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.
Why is my p1326 engine code not up to date?
Your Snap-On scanner may not be up to date. Fault P1326 was added the the PCM via a software update to detect engine bearing failure using the knock sensor. The system is flawed, electrical interference in the wiring can cause false alarms. An overlay wiring harness has been developed to correct the false alarms.
How much does it cost to repair a p1326 Hyundai?
The cost of diagnosing the P1326 HYUNDAI code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. The Knock Sensor Detection System (KSDS) detects vibrations indicating the onset of excessive connecting rod bearing wear.
Is there check engine warning lamp on 2015 Sonata?
Description:Certain 2015MY Sonata vehicles with 2.0L Turbo and 2.4L engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.
Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P1326 HYUNDAI code is 1.0 hour of labor.
When do I get the error code p1320?
Error Code P1320 is defined as Ignition Signal, or Ignition Coil and Power Transistor. This code is set when the ignition signal in the primary circuit is not sent to the PCM (powertrain control module, also known as ECM or engine control module in other vehicle makes) during engine cranking or running.
Where do I find the fault code on my Hyundai?
Connect your OBD-II scanner into the OBD-2 port under the dashboard on the driver’s side. Note: Even a $20 generic OBD-2 scanner can retrieve check engine / ECU Hyundai fault codes. Those are P-codes in the Hyundai list below.
What causes the p0138 OBD-II trouble code?
All our repairs are backed by our 12-month / 12,000-mile warranty. P0138 is the OBD-II generic code indicating the O2 sensor for bank 1 sensor 2 fails to have a lower voltage output below 1.2 volts for more than 10 seconds indicating a lack of oxygen in the exhaust stream. What causes the P0138 code?