How to remove shift cable from Hyundai Santa Fe?

Remove the floor console. 2. Remove the air duct. 3. Disconnect the shift cable (A). 4. Remove the retainer (A) and nut (B). 5. Remove the nut (C) from the manual control lever. 6. Remove the cable (B) from the bracket (A) at transaxle assembly side. 7. Remove the shift cable by pulling it toward the interior. 1.

What to do if your Hyundai Santa Fe won’t start?

If you have a model of Santa Fe which only has a key fob with start/stop button and no place to insert a key, then try placing your key fob as close to the start/stop button as you can and then start the vehicle. Start/Stop button on Hyundai Santa Fe fourth generation TM Tip: You can try starting your Santa Fe with its second key.

What makes a Hyundai Santa Fe stay in Park?

The shift lock solenoid is the mechanism that keeps you from shifting out of park without your foot on the brake. The good news is that most shift locks have an override button. You will need to find it for your particular model year of Santa Fe (if applicable). Finding it is usually pretty easy.

Why is my Santa Fe stuck in Park?

If you are positive that the gear shifter is not stuck in park (see directly above), then it’s likely that the shift linkage may be bad. Either something caused it to bend, or it’s starting to come loose. If it’s come loose, the geometry won’t be right anymore and it may keep your Santa Fe stuck in park.

Where is the shift lever on a Hyundai Santa Fe?

You can start the engine with the shift lever in the N (Neutral) position. But, for your safety, we recommend that you start the engine with the shift lever in the P (Park) position. • It means that any door is open.

What do the warning messages on my Hyundai Santa Fe mean?

Check fuse “BRAKE SWITCH” (for smart key system and automatic transaxle) This warning message illuminates if the brake switch fuse is disconnected. It means that you should replace the fuse with a new one. If that is not possible, you can start the engine by pressing the Engine Start/Stop Button for 10 seconds in the ACC position.

What should the voltage of a Hyundai Santa Fe battery be?

The voltage of the battery on your Hyundai Santa Fe can be measured precisely with a multimeter. Before the test, the multimeter is set to the voltage range of the battery and connected to its plus and minus poles. Successful testing of the car battery, i.e. checking the voltage, usually results in values of approx. 12 to 13 volts.

What are the problems with the Hyundai Santa Fe transmission?

Transmission slams into gear, also slips into gear and sometimes moves when in park. Car jerks violently when at highway speed even though it has new shocks, struts, and front drive axles. The transmission also seems to engage suddenly when moving forward from complete stop. Regular maint.

Why does my Santa Fe hesitate when shifting from 1st to 2nd gear?

Sometimes when it shifts from 1st to 2nd it feels like another vehicle has rear-ended me. It happens a lot when the Santa Fe is cold, but it has happened at other times also. It will also hesitate as it goes from one gear to the next.

When did my Hyundai Santa Fe go down a hill?

On March 11, 2011 I parked my 2009 Hyundai Santa Fe in my driveway. As I was geting out of the vehicle it started to move. It dragged me down my driveway and as I was trying to get back into the vehicle I banged my right knee on the the steering wheel and it turned and went down a hill and hit a tree with me still hanging half out of the vehicle.

Are there any problems with the Hyundai Santa Fe?

Another problem some drivers encountered was a stutter in the transmission. This was reported in Hyundai Santa Fe years 2001 through 2014 with automatic transmissions. Both front-wheel drive and all-wheel drive models were affected.

What kind of engine does the Hyundai Santa Fe have?

The crankshaft position sensor failure affected quite a few engines in the Santa Fe lineup, including Hyundai’s 2.0-liter four-cylinder, 2.4-liter four-cylinder turbo, 2.7-liter V6, 3.3-liter V6, and 3.5-liter V6 engines. The problem occurred at an average mileage of 103,710 miles.

Why does my Hyundai Santa Fe shutter when I change gears?

Both front-wheel drive and all-wheel drive models were affected. Drivers said that the vehicle would shutter when changing from second to third gear and that it jerked as if it didn’t know what gear to go into. Most drivers said this happened when they were first driving the vehicle and not once it had warmed up.

Is the third row seat on the Hyundai Santa Fe?

One notable deletion from the 2010 Hyundai Santa Fe’s options list is the third-row seat. While going from a seven- to a five-passenger interior may put off some buyers, we don’t consider it a great loss because that way-back seat was so cramped and difficult to access it was really only fit for small and nimble children.

What kind of transmission problem does Hyundai Santa Fe have?

242-horsepower 3.3L V6 5-speed shiftable automatic AWD fluid leaking from left trans output seal. removed left lower control arm and removed axle. replaced seal. Shift cable seized. SUV would not start (safety precaution?) pinion seal leaked into rear diff drive coupling alowing it to slip. electro magnet clutch assembly

Why is my shifter hard to get out of Park?

Sometimes my shifter is hard to get out of park. what would cause this, and how would I fix it? make sure the brake light switch is working , that sends currant to a solenoid on the shifter to release a latch, or take it apart and remove the latch 55 people found this helpful. this is on the back of the break pedal? 48 people found this helpful.

How do you get a Hyundai shifter out of Park?

How to manually release Hyundai shifter. Set the parking brakes. Risk of vehicle rolling when the shifter is moved out of Park. Locate shift lock override and remove the cap. Insert a flat screwdriver into the access hole and press down. Move the shifter out of the park.

Why does my Santa Fe shift from Park to drive?

Customerreply replied 8 years ago Initially it would not move from park into any gear. then the AAA depressed the shift lock release and was able to get it into neutral then drive. When it was in drive the vehicle moved fine, no issues. Then when I stopped at my house, and went to put it in park the shifter would not go into park.

Is the gear shift lever stiff on a Hyundai Santa Fe?

I have a 2008 hyundai santa fe. today i went to shift from park to drive and the gear shift lever was stiff and would I have a 2008 hyundai santa fe. today i went to shift from park to drive and the gear shift lever was stiff and would – Answered by a verified Hyundai Mechanic We use cookies to give you the best possible experience on our website.

Is it possible to put a Hyundai Santa Fe into drive?

You said initially you could not get the shifter to move past Neutral and into Drive, but later you said the car would not shift into any gear until the shift lock release was pressed. Is this to say that with the shift lock release pressed you could put it into Drive normally?

What to do if your Hyundai Santa Fe is stuck in Park?

The engine is running fine, but the shifter just won’t move. There are several things you can try to get your Hyundai Santa Fe moving now. These include checking to see if the parking brake is stuck, finding the shift lock solenoid override (if applicable), and the shift linkage. Let’s get straight to it.

Navigation