What does check engine light on Hyundai Genesis mean?
A check engine light can indicate a broad spectrum of problems with your 2009 Hyundai Genesis. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.
What should I do if my check engine light is on?
Steady Check Engine Light: If your check engine light is on every time you operate your Genesis, you need to have it checked as soon as possible, especially if you notice performance problems or unusual noises.
Why does my Hyundai Elantra have a check engine light?
Has the check engine light turned on in your Hyundai Elantra, Accent, Sonata, Kona, or Santa Fe? It can be alarming seeing an engine warning appear on your dashboard, especially if you’ve never seen it before. A wide array of issues can cause a check engine light to come on, some more serious than others.
Why does my Infiniti check engine light keep blinking?
Gas cap issues can reduce fuel pressure and allow fuel vapors to escape, reducing fuel economy and increasing harmful emissions. Failing Catalytic Converter: Your catalytic converter can eventually clog with material, especially with higher mileage vehicles.
What causes a check engine light on a Hyundai?
Fortunately AutoNation Hyundai North Richland Hills is here to help you figure out what might be wrong, and what your next steps should be. Below we have highlighted the most common causes of a check engine light. Loose Gas Cap: Your gas cap is loose, broken, or simply missing.
What to do when a Genesis warning light comes on?
If the warning light comes on while the vehicle is in motion: 1. Drive to the nearest safe location. 2. With the engine off, check the generator drive belt for looseness or breakage. 3. If the belt is adjusted properly, a problem exists somewhere in the electrical charging system.
When does the Genesis dashboard indicator turn off?
However, when the smart key is not in the vehicle, if the engine start/stop button is depressed, the indicator will blink for a few minutes to indicate that you will not be able to start the engine. When the ignition switch is turned to the ON position and the indicator turns off after two seconds, the system may have a problem.
What to do when your check engine light comes on?
No matter the situation, when the check engine light comes on in your Hyundai, we always suggest stopping by our service center so one of our knowledgeable technicians can properly diagnose and repair your vehicle. Our service technicians have the most up-to-date diagnostic equipment that can quickly read Hyundai OBD-II Trouble Codes.
What happens if you reset check engine light?
Warnings. Erasing codes by disconnecting your vehicle’s battery can also clear out the memory for your radio and other on-board components. This method is recommended as a last resort. The emissions monitors in your vehicle will register being reset, so you will not pass emissions if you bring in a car with the codes being reset.
How to reset check engine light with OBD-II?
1 Connect the scan tool to the OBD – II Connecting the scan tool to the OBD- II ( On- board diagnostic connector) under your steering column. 2 View error codes by pressing the “READ” button Pressing the “READ” button on the scan tool to see the error codes of the engine. 3 Remove the error code
How can I remove an error code from my Check Engine light?
Pressing the “READ” button on the scan tool to see the error codes of the engine. You should need a pen to write down the code or codes in the order they were received for future repairs or reference if needed. Pressing the “ERASE” button on the scan tool to remove the error code.
A check engine light can indicate a broad spectrum of problems with your 2009 Hyundai Genesis. In some cases you need to pull over immediately to prevent damage while in others you merely need to tighten you gas cap next time you stop in order to reset the service engine soon light.
What to do if your engine light is on?
Engine Light Is On: 2009-2014 Hyundai Genesis – What to Do 1. Getting Started – Prepare for the repair 2. Locate OBD Port – Find the OBD port on your vehicle 3. Scan for Codes – How to scan your vehicle for trouble codes 4. More Info. – Additional information on check engine lights Share on David Hobbshelped make these videos Feedback
Has the check engine light turned on in your Hyundai Elantra, Accent, Sonata, Kona, or Santa Fe? It can be alarming seeing an engine warning appear on your dashboard, especially if you’ve never seen it before. A wide array of issues can cause a check engine light to come on, some more serious than others.
Why is my engine light on in my Alfa Romeo?
Faulty Oxygen Sensor: Due to long exposure to hot exhaust gas, your oxygen sensor might need replacing. The oxygen sensor provides vital air-fuel mixture information to the ECU. A faulty oxygen sensor can cause your vehicle’s computer to supply the engine with too much or too little fuel.
Faulty Oxygen Sensor: Due to long exposure to hot exhaust gas, your oxygen sensor might need replacing. The oxygen sensor provides vital air-fuel mixture information to the ECU. A faulty oxygen sensor can cause your vehicle’s computer to supply the engine with too much or too little fuel.
Why is the warning light not working on my genesis?
If the warning light does not come on, when you turned the engine start/stop button to the ON position, the Adaptive Front Light System is not working properly. If it blinks while driving, the Adaptive Front Light System is not working properly. Take your vehicle to an authorized Genesis service location and have the system checked.
What does it mean when your Genesis engine is overheating?
If the belt is adjusted properly, a problem exists somewhere in the electrical charging system. Have an authorized Genesis service location correct the problem as soon as possible. This warning message illuminates when the engine coolant temperature is above 248 °F (120 °C). This means that the engine is overheated and may be damaged.