Is the Hyundai Santa Fe camshaft position sensor genuine?
We offer a full selection of genuine Hyundai Santa Fe Camshaft Position Sensors, engineered specifically to restore factory performance. Please narrow the Cam Position Sensor results by selecting the vehicle.
What should I do about my Hyundai Santa Fe?
Hyundai Santa Fe: Camshaft Position Sensor (CMPS). Repair procedures Hyundai Santa Fe DM 2013-2018 Service Manual / Engine Control/Fuel System / Engine Control System / Camshaft Position Sensor (CMPS). Repair procedures 1.
What is the input speed sensor on a Santa Fe?
Description Input speed sensor (A) is a vital unit that measures the rate of rotation of the input shaft inside the transaxle and delivers the readings to the Transaxle Control Module (TCM). The sensor Drive Plate. Repair procedures
What does p0016 stand for in Hyundai Santa Fe?
P0016 is know to occur in the Hyundai Santa Fe when the Crankshaft Position Sensor and the Camshaft Position Sensor are out of alignment by a certain number of degrees, or if there is a sensor issue. We’ll explore the symptoms and causes directly below. P0016 refers to which camshaft position sensor is out of time with the Crankshaft.
How to replace the camshaft position sensor on a Hyundai Santa Fe?
Camshaft position sensor packed in the other day and there were no video’s on here to show how to replace it ( perhaps because of how easy it was ), So here goes. Fault: Car kept cutting out and failing to start, ignition would turn over but nothing else. Fault Code on the diagnostics machine P0340. Part Number 39300-27000.
What are the components of a Hyundai Santa Fe?
Variable Intake Solenoid (VIS) Valve 23. Fuel Pressure Regulator Valve 24. Canister Close Valve (CCV) 25. Ignition Coil 26. Main Relay 27. Fuel Pump Relay 28. Data Link Connector (DLC) [16-Pin] 29. Multi-Purpose Check Connector [20-Pin] 1. Engine Control Module (ECM) 2. Manifold Absolute Pressure Sensor (MAPS) 3.
P0016 is know to occur in the Hyundai Santa Fe when the Crankshaft Position Sensor and the Camshaft Position Sensor are out of alignment by a certain number of degrees, or if there is a sensor issue. We’ll explore the symptoms and causes directly below. P0016 refers to which camshaft position sensor is out of time with the Crankshaft.
Why does my Santa Fe camshaft rattle so much?
The camshaft typically will have a ring that provides the same function. Often when a reluctor ring goes bad, it’ll rattle quite a lot. That is a very good indication that there is an issue with it. Here’s a good video on diagnosing P0016:
Why does my Santa Fe have a p0016 sensor?
A lot of the harness leading to and from the Crank/Cam sensors is going to be exposed to hot exhaust and vibration. This is a great place to start diagnosing P0016 in your Hyundai Santa Fe. It’s quick and easy to do this before moving on to the sensors themselves.
The camshaft typically will have a ring that provides the same function. Often when a reluctor ring goes bad, it’ll rattle quite a lot. That is a very good indication that there is an issue with it. Here’s a good video on diagnosing P0016:
Why is my crank not working on my Santa Fe?
If this ring fails, the vehicle will not be able to get an exact crank position. The camshaft typically will have a ring that provides the same function. Often when a reluctor ring goes bad, it’ll rattle quite a lot. That is a very good indication that there is an issue with it.
How do you replace the crank shaft sensor on a Hyundai Santa Fe?
Remove the two bolts holding the sensor in place with a socket. Remove the sensor from its position. Insert the replacement crankshaft sensor in position, lining up the bolt holes. Thread the bolts in place and tighten them with a socket. Plug the wire connector into the sensor.
Where is the CKP sensor on a Hyundai Santa Fe?
The sensor sends a signal to the power control module to calculate ignition timing, fuel injector timing, misfire diagnostics and the tachometer display. The CKP sensor is located at the front of the engine, next to the crankshaft. Open the hood of the Hyundai Santa Fe.
We offer a full selection of genuine Hyundai Santa Fe Camshaft Position Sensors, engineered specifically to restore factory performance. Please narrow the Cam Position Sensor results by selecting the vehicle.
Hyundai Santa Fe: Camshaft Position Sensor (CMPS). Repair procedures Hyundai Santa Fe DM 2013-2018 Service Manual / Engine Control/Fuel System / Engine Control System / Camshaft Position Sensor (CMPS). Repair procedures 1.
Description Input speed sensor (A) is a vital unit that measures the rate of rotation of the input shaft inside the transaxle and delivers the readings to the Transaxle Control Module (TCM). The sensor Drive Plate. Repair procedures
How do you remove a camshaft position sensor?
You should make out the plug with the wire and see that the sensor is being mounted with 1 10mm bolt. 1. Disconnect negative battery cable. 2. Disconnect wire connector from sensor. 3. Remove sensor mounting bolts. 4. Remove the sensor from the rear of cylinder head. 1. Install camshaft position sensor in rear of cylinder head. 2.
When to remove the camshaft position sensor ( CMPs )?
DON’T remove the camshaft position sensor while the engine is running or right after engine is turned off. The part and engine oil is hot and can cause burns. 1. Turn the ignition switch OFF and disconnect the battery negative (-) cable.
How to diagnose Hyundai Santa Fe p0016?
This is a great place to start diagnosing P0016 in your Hyundai Santa Fe. It’s quick and easy to do this before moving on to the sensors themselves. Make sure to check the harness where it plugs into both sensors as well. After examining the wiring harness, it would be time to check the sensors themselves.