How do I reset my Plantronics CS55?

How do I reset my Plantronics CS55?

To reset your CS50/CS55/CS60:

  1. Press in and hold the mute control (A) and the talk button (B) until the talk indicator light (C) on the headset starts blinking rapidly.
  2. Press and hold the talk button (B) again.
  3. Disconnect the AC power supply from the bottom of the base.
  4. Test the headset to ensure it works properly.

How do I reset my Plantronics PLT?

Press the power button for about 5-6 seconds until the indicator light starts flashing red and blue. Press the volume up and volume down buttons at the same time. The light flashes rapidly 3 times, and then the headset turns off.

Why does my Plantronics headset keep cutting out?

This typically occurs when the smart phone is downloading or sending information (using data) while you’re using the headset. The best solution for this issue is to keep the headset as far away as possible (at least 4-5 feet is recommended) from the mobile phone.

How do I fix feedback on my Plantronics headset?

If the listening volume is too low, adjust the setting on the wireless base to increase the volume (pic below) If the sound level is still low, adjust the setting on the wireless headset itself to increase the volume. If the echo problem continues to persist, lower the speaking volume on the base.

How do I resync my Plantronics headset?

Start with your headset powered on. Press and hold the call control button for 5 or 6 seconds until the light starts flashing red and blue (some models flash red and white). Release the button and set the headset aside. Follow the pairing instructions for your cell phone or other Bluetooth device.

How do I reset my Plantronics PLT v5200?

Reset Sensors

  1. Wearing the Voyager 5200, tap the call button to test sensors.
  2. To reset the sensors, power on the headset, connect the headset to your computer’s USB port for more than 10 seconds.
  3. You can disable your headset smart sensors through the Plantronics Hub software under the Settings.

How do I fix my headphones that cut out?

Through twists and bends

  1. Insert your headphones or earphones into your phone or musical device and play some music.
  2. Hold a part of the wire near the earpiece and bend or jiggle it.
  3. Make your way to the other end of the wire and jiggle every inch until you hear the headphone sound gets cut out.

Why do my headphones keep glitching?

Another issue that can occur is that the audio port of your playback device is the one causing the static noise. This usually happens when the inside of the auxiliary port of the device is dirty and oxidized which affects the quality of audio of your headphones.

How do you fix a Echoing headset?

The method to fix echo in headphones easier

  1. Unplug and replug your headphones.
  2. Reduce the volume on the speaker.
  3. Move the Microphone around.
  4. Turn off the microphone when not in use.
  5. Make sound settings on the device.
  6. Switch to another device.
  7. Listen to this device.
  8. Disable all enhancement.

How do I reset my Plantronics Bluetooth headset?

Reset Plantronics Bluetooth Headset

  1. Remove the Plantronics headset from your cell phones paired devices.
  2. Power your cell phone off, then power it back on.
  3. Pair your Plantronics headset back to your cell phone (follow manual if unsure how)
  4. Your Plantronics headset should now be reset.

How do I factory reset my Plantronics 5200?

Voyager 5200 Reset

  1. Unpair the Voyager 5200 headset from your cell phone.
  2. Power off your cell phone.
  3. Power on your cell phone.
  4. Re-pair the Voyager 5200 headset to your cell phone.
  5. Test the headset to see if that helped. If not follow the Voyager 5200 firmware update.

How to do a system reset on Plantronics CS50?

To perform the system reset, follow this procedure: 1. Press both the talk button (14) and the mute control button (15) on the headset for 5 seconds. 2. When the talk indicator light (17) on the headset blinks, release both buttons. 3. Press the talk button again.

Is it possible to reset a CS55 headset?

On rare occasion, you may experience static or crackling when using your CS55 wireless headset. Following the steps below will allow you to “reset” the CS55 headset back to it’s original working state. This takes less than 30 seconds and is rarely required to be repeated in the future.

How to reset the battery on a Plantronics headset?

1 Unplug the AC power from your Plantronics charging base. 2 Remove your battery (CS70n, CS530, C053 battery can’t be removed) 3 Wait 10 seconds, then replug your AC power and battery. 4 Your Plantronics headset should now be reset and working Plantronics CS50 and CS55 battery replacement guide Plantronics CS351n, CS361n, C052, CS510,

How does the intellistand work on the Plantronics CS50?

The IntelliStand feature senses when the headset has been removed or placed into the CS50 base unit which automatically activates the Handset Lifter and enabling headset/handset mode to answer or end the call. There is a switch towards the bottom on the right side of the base unit that will switch the IntelliStand feature On and Off.

Posted In Q&A