Where do I find the fault code on my Hyundai?

Connect your OBD-II scanner into the OBD-2 port under the dashboard on the driver’s side. Note: Even a $20 generic OBD-2 scanner can retrieve check engine / ECU Hyundai fault codes. Those are P-codes in the Hyundai list below.

What is the computer code for a Hyundai?

COMPUTER CODES for Hyundai Vehicles. If codes other than these are indicated, repeat self-diagnosis. If codes reappear, substitute a known good ECM, and recheck codes. Hyundai Stellar vehicles.

What is the DTC code for a Hyundai?

In this article, you will find a complete list of Hyundai Trouble Codes. This list contains more than the Hyundai Check Engine Codes. Here you will find Hyundai ABS, Airbag, and Transmission DTC codes. P0244 Turbocharger/Supercharger Wastegate Sol.

How do I erase the Diagnostic Code on my Hyundai?

The last output consist of the end of output code 3333. To erase any diagnostic codes, disconnect battery ground cable for 15 seconds and the ECM (ECU) memory will be erased. COMPUTER CODES for Hyundai Vehicles. If codes other than these are indicated, repeat self-diagnosis.

Is it okay to drive a Hyundai with p0171 code?

Vacuum leaks – PCV hose, vacuum hoses, intake manifold gasket. It is okay to drive your Hyundai with P0171 for a short period of time, but driving with this code for an extended period of time can overheat the engine and cause internal engine damage.

What to do if check engine light code p0171 is triggered?

If check engine light code P0171 is triggered again, check the rest of the vacuum lines for leaks and continue to the rest of the diagnostic process. Remove the mass air flow sensor and clean the sensor using mass air flow cleaner or contact cleaner. Reinstall the mass air flow sensor and clear the check engine light using FIXD.

What are the symptoms of a Hyundai p0011 DTC?

Most likely a P0011 Hyundai DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

Where is the a camshaft on a Hyundai p0011?

The “A” camshaft is either the intake, left, or front camshaft. Most likely a P0011 Hyundai DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.

What kind of engine codes does a Hyundai have?

This list contains more than the Hyundai Check Engine Codes. Here you will find Hyundai ABS, Airbag, and Transmission DTC codes. P0244 Turbocharger/Supercharger Wastegate Sol. ‘A’ Range/Performance P0245 Turbocharger/Supercharger Wastegate Sol. ‘A’ Low P0246 Turbocharger/Supercharger Wastegate Sol. ‘A’ High

What is the fault code for the Hyundai Elantra?

Hyundai Sonata, Excel 90 on , Scoupe 91 & 92 , Elantra. Hyundai Scoupe 93 through 95 and Accent vehicles. 4155 ECM failure A/C relay, IAC, PC.” You will need a Hyundai multi-system OBD-2 scanner to read Hyundai specific fault codes.

What is the fault code for a Hyundai airbag?

Airbag Fault Code DTC B1101 Battery Voltage High B1102 Battery Voltage Low B1326 FIS Front Impact Sensor -Driver Short to Ground

Can a Hyundai service plan Keep you on the road?

A Hyundai Service Plan is the perfect way to keep your car on the road and enjoy more of the freedom that being a Hyundai driver brings.

What to do if you have a complaint about a Hyundai?

If you’ve had unsatisfactory service, have concerns about your warranty, need to issue a complaint about your vehicle, or have received a solicitation letter from a lemon law attorney, please let us know.

Can a Hyundai technician take care of your car?

Trained Hyundai technicians will expertly assess and service your Hyundai, replacing and repairing any faults with guaranteed Hyundai parts. So you know your car is in the very safest hands. They will also check and perform any recommended updates on your car free of charge.

What do you need to know about Hyundai customer service?

Let us help you. All of us at Hyundai are working to deliver exceptional customer service and complete owner satisfaction. While we take pride in our brand and are committed to always improving vehicle quality, technology, and service, we understand that sometimes problems can arise. If they do, we want to be the first to help.

How to contact Hyundai Motor Finance for payment?

If your recurring payment schedule was set up through a dealership, bank, or other third party bill-pay service, contact them for information. If your recurring payment schedule was set up through Hyundai Motor Finance, Contact Us for more information. Why am I being charged Property/Excise Tax on a leased vehicle?

What to do if your Hyundai payment schedule has been cancelled?

Your recurring payment schedule has been cancelled. If your recurring payment schedule was set up through a dealership, bank, or other third party bill-pay service, contact them for information. If your recurring payment schedule was set up through Hyundai Motor Finance, Contact Us for more information.

Airbag Fault Code DTC B1101 Battery Voltage High B1102 Battery Voltage Low B1326 FIS Front Impact Sensor -Driver Short to Ground

What does the car code u0001 stand for?

What does code U0001 mean? Code U0001 stands for High Speed Communication Area Network (CAN) Bus. Modern vehicles have many computers on board. These computers (referred to as modules) communicate with one another via the controller area network (CAN) bus.

What is the cause of the error code u0101?

Common causes for U0101. Code U0101 is typically caused by one of the following: A dead battery. A faulty TCM. A problem with the TCM circuit. A problem with the CAN bus.

How long does it take to repair a p0501 Hyundai?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P0501 HYUNDAI code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type.

What are the symptoms of an OBD code u0001?

U0001 symptoms 1 An illuminated check engine light 2 A secondary code specifying a failed module 3 Performance problems ranging from the vehicle not starting to the air conditioning not working, depending on which module is unable to communicate

Where is the Diagnostic Code on a Hyundai?

With ignition switch in the On position, ground the No. 10 terminal (L wire) of diagnostic connector for approximately 2.5 seconds. The diagnostic connector is located on the left hand kick panel. The first diagnostic trouble code or no fault detected will be indicated by the on-board diagnostic lamp.

What are the computer codes for Hyundai Sonata?

COMPUTER CODES for Hyundai Vehicles. CODE Hyundai Sonata, Excel (90 on), Scoupe (9 1 Electronic Control Unit (ECU) (one long 2 ECU system normal 11 Oxygen sensor or circuit 12 Airflow sensor or circuit

What does the code u0101 on a car mean?

What does code U0101 mean? Code U0101 stands for Lost Communication with TCM. The transmission control module (TCM) is the computer that controls your vehicle’s transmission. Various sensors provide input to the TCM.

What are the OBDII Codes for a Hyundai?

OBDII Codes definition for car manufacturer Hyundai: B0001. B0002. B0003. B0004. B0005. B0010. B0011. B0012.

Where is the OBD plug on a Hyundai Santa Fe 2?

OBD connector location for Hyundai Santa Fe 2 (2006 – 2012) You will find below several pictures which will help you find your OBD connector in your car. Connector is under steering wheel near pedals. Go to the OBD2. scanner for HYUNDAI. OBD Connector is above the brake pedals. Those pictures were sent by Fabrizio.

What is the ABS warning light on a Hyundai Santa Fe?

The contact owns a 2014 Hyundai Santa Fe. The contact stated while driving 55 mph, the abs warning light was illuminated. The contact received notification of NHTSA campaign number: 20v520000 (service brakes, hydraulic).

What does p0501 mean on a speed sensor?

Basically a P0501 trouble code means that the vehicle’s speed as read by the Vehicle Speed Sensor (VSS) is outside of the expected range (too high or low for example).

What is the DTC code for a Hyundai Sonata?

Here you will find Hyundai ABS, Airbag, and Transmission DTC codes. P0244 Turbocharger/Supercharger Wastegate Sol. ‘A’ Range/Performance P0245 Turbocharger/Supercharger Wastegate Sol. ‘A’ Low P0246 Turbocharger/Supercharger Wastegate Sol. ‘A’ High Hyundai Sonata, Excel 90 on , Scoupe 91 & 92 , Elantra.

What does the OBD2 code p0501 mean?

OBD2 Code P0501 Hyundai definition: Basically this means that the vehicle’s speed as read by the Vehicle Speed Sensor (VSS) is not working properly.

Why is the Check Engine light coming on on my Hyundai Sonata?

The check engine light on your Hyundai Sonata will usually shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it’s tightened, the light will turn itself off.

What causes a p0501 DTC trouble code?

A P0501 DTC trouble code may be caused by one or more of the following: The Vehicle Speed Sensor (VSS) is not reading (functioning) properly There is a broken/frayed wire leading to the vehicle speed sensor

What causes a check engine light on a Hyundai?

Fortunately AutoNation Hyundai North Richland Hills is here to help you figure out what might be wrong, and what your next steps should be. Below we have highlighted the most common causes of a check engine light. Loose Gas Cap: Your gas cap is loose, broken, or simply missing.

What’s the error code on my Hyundai Sonata?

Once in a while the check engine light flashes after it shifts into 2nd, it is an automatic transmission, onc… 2002 Hyundai Sonata 105,000 miles, 2.4 L MFI DOHC error code PO340. have replaced timing belt, pluges and wires, both ignition coils, Camshaft position sensor (twice). Car runs fine till it warms ups.

How to diagnose p0340 OBD-II trouble code?

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try: Visually inspect all the wiring and connectors in the circuit Check for continuity in the circuit wiring Check the operation (voltage) of the camshaft position sensor Replace the camshaft position sensor as required

What are the codes for the Hyundai Elantra?

If codes reappear, substitute a known good ECM, and recheck codes. Hyundai Stellar vehicles. Hyundai Sonata, Excel (90 on), Scoupe (91 & 92), Elantra. Hyundai Scoupe (93 through 95) and Accent vehicles.

Why is my Hyundai Santa Fe not turning?

If you’ve broken a drive/axle shaft, your Hyundai Santa Fe’s transmission has no way to turn the wheels anymore. If this were the case, there would not be any movement whatsoever from the vehicle. You also wouldn’t feel the slight jerk your Santa Fe as you put it into gear.

What causes a Hyundai engine code p0171 to fail?

P0171 HYUNDAI – System Too Lean Bank 1… Possible causes – Intake air leaks – Faulty front heated oxygen sensor – Ignition misfiring – Faulty fuel injectors – Exhaust gas leaks – Incorrect fuel pressure – Lack of fuel – Faulty Mass Air Flow (MAF) sensor – Incorrect Positive Crankcase Ventilation (PCV) hose connection.

What is the serial number on a Hyundai Santa Fe?

Below is a sample of an VIN taken off my Santa Fe minus the serial number… Vehicle Identification Number System for the Hyundai Manufacturing Company. 00 W.I.C. Model Vehicle Serial Number KM 08 S32C7 3D U000 1 2 3 4 7 8 9 10 11 12 13 14 15 16 1756

What kind of car is the Hyundai Santa Fe?

Door Sedan Door Hatchback Coupe Wagon AWD Door Hatchback Deluxe Super Deluxe (L) (GL) (GLS,LS, or GS) (Excluding 2000 Accent Standard Wagon FWD Bromont Assembly Plant, Canada Alabama Assembly Plant, USA (projected) Model / Vehicle Line

What are the functions of Hyundai diagnostic software?

Unlike other universal car scanner tools which only read fault codes, this software performs nearly ALL the functions like the original dealer diagnostic tool. The following diagnostic functions are supported: Displays complete identification of control unit, e.g. part number, software/hardware version, manufacturer, etc…

What does it mean when your Hyundai i20 won’t start?

The first and most common is when it won’t turn over. This just means that the engine doesn’t move when you turn the key. The second way that your i20 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own.

Are there any problems with the Hyundai push button start?

We have been frequently writing about the dilemmas Hyundai drivers are encountering, including alignment issues and transmission troubles .Now comes a new one on the horizon: A problem with the Hyundai push button start. The message boards are blowing up with folks who are being left stranded by the Hyundai push button start problem.

Is there a problem with my Hyundai Hyudai?

I had exactly this problem with my Hyudai !10. Intermittent starting, sometimes from cold and sometimes from hot. I picked up some clues and tried the following. 1. Disconnected the battery negative and reconnected. 2. Lifted the air cleaner and sprayed the plug leads with WD40 equivalent. 3.

What is the P2006 OBD2 diagnostic trouble code?

The P2006 code is a generic OBD2 diagnostic trouble code relating to the intake manifold runner control circuit.

Where is the OBD connector on a Hyundai Tucson?

OBD connector location for Hyundai Tucson (2004 – 2010) You will find below several pictures which will help you find your OBD connector in your car. The OBDII plug is located under the steering wheel on the left. Go to the OBD2. scanner for HYUNDAI. The OBDII port is on the right of the hood lever. Those pictures were sent by.

What are the problems with a 2006 Hyundai Tucson?

Worst 2006 Hyundai Tucson Problems #1: Rough Idling (Diesel Clatter) 2006 Tucson Average Cost to Fix: N/A. Average Mileage: 12,000 mi #2: Battery Continually Dies 2006 Tucson Average Cost to Fix: N/A. Average Mileage: 54,000 mi #3: Loss Of Pickup 2006 Tucson Average Cost to Fix: N/A. Average Mileage: 12,000 mi

The P2006 code is a generic OBD2 diagnostic trouble code relating to the intake manifold runner control circuit.

What does a p0123 mean on an OBD code?

A code P0123 may mean that one or more of the following has happened: 1 TPS not mounted securely 2 TPS circuit short to ground or another wire 3 Faulty TPS 4 Damaged computer (PCM)

What is the fault code for a Hyundai excavator?

Troubleshooting of Hyundai Excavator fault code DTC / error code Hyundai 9 series excavators error codes: 101 3 hydraulic oil temperature sensor circuit – Voltage above normal or shorted high voltage 4 hydraulic oil temperature sensor circuit – Voltage below normal or shorted to low voltage

What are the error codes for Hyundai OBD-II?

Bir Hyundai bütün, Özel OBD-II hata kodlarını Listeleme. kodlar Tüm Hyundais Için Cardio olmalıdır. Unknown 936607 , 936007, 001000 Idle Speed Act. (Close) – Short Idle Speed Act. (Close) – Open Voltage Regulator For Inject. Power Stage Group A Malfunction. Key ID. Not Valid L.O2s Pump. Circuit – Open (B1/S1) L.O2s Pump. Circuit – Low (B1/S1)

How can I tell if my Hyundai is malfunctioning?

Reading and decoding Hyundai error codes is the easiest and most accessible way to determine the malfunction of your car. Knowing the error codes of Hyundai and their meanings, you can easily make a “diagnosis”, and possibly yourself “cure” the car.

How do you repair a Hyundai multi use tester?

Connect power-source terminal of multi-use tester to cigarette lighter socket. Turn ignition switch On, then use multi-use tester to read self-diagnostic codes. Repair any malfunctions found using tester. Turn ignition switch Off, then disconnect battery ground cable for 10 seconds.

Which is the standard list of fault codes?

Standard or generic fault codes are a list of codes common to all manufacturers. This list of faults, also called DTC (for Data Trouble Code) has been defined so that any diagnostic device can read and decode them. They have a standard format as shown below :

How do you find the fault code on a Toyota Hilux?

– Connect the “TC” and “E1” terminals of the DLC1 connector (the car is stationary). – Depress the brake pedal eight or more times in the interval of three seconds. – The indicator should output the normal code (flashing 2 times per second). – Switch off the ignition. – Remove the jumper from the terminals “TC” and “E1”.

What are the IH fault codes for a forklift truck?

ENG 431 Hand Throttle (STD cab) Idle Validation Switches are both closed ENG 432 Hand Throttle (STD cab) position potentiometer and switches disagree. ENG 433 Boost Pressure level disagrees with engine operation conditions (speed & power) ENG 434 Unswitched 12 volt supply voltage disconnected without normal key off sequence.

Where are fault codes stored in a car?

Diagnostic trouble codes (or fault codes) are codes that are stored by the on-board computer diagnostic system. These are stored in response to a problem found in the car by the system.

What causes a DTC to report a fault?

For example, if a DTC reports a sensor fault, replacement of the sensor is unlikely to resolve the underlying problem. The fault is most likely to be caused by the systems that the sensor is monitoring, but might even be caused by the wiring to the sensor itself. DTCs may also be triggered by faults earlier down the line.

Which is the most accurate check engine light code?

P1270Accelerator Pedal Position Sensor A/D Converter Error P1271APP Sensor 1-2 Performance P1272Accelerator Pedal Position Sensor 2 P1273Accelerator Pedal Position Sensor 1

What causes an EOBD fault code ( DTC )?

DTCs may also be triggered by faults earlier down the line. For example, a dirty MAF sensor might be causing the car to overcompensate in its fuel-trim adjustments. As a result, oxygen sensors are likely to report fuel mixture problems.

Navigation