How do I fix the E20 error on my Electrolux washing machine?

How do I fix the E20 error on my Electrolux washing machine?

The problem may be solved by switching off the power to the washing machine for about 1-2 hours and then starting a wash cycle again. If the pump has been blocked, a bimetal fuse will switch off the pump. When the pump has cooled down, it should work normally.

What is error E20 on Electrolux washing machine?

Cause. error message E20 indicates a drainage, pump or software problem.

What is E20 error code on AEG washing machine?

Appliance displays error code E20, E21 or C2 – or emits 2 beeps / 2 flashes when your machine has detected that the drum of the machine will not drain. Warning: We do not recommend using the appliance until the problem has been completely fixed.

How do you manually drain an Electrolux washing machine?

How to Drain a Top-Loading Washing Machine

1. STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one.
2. STEP 2: Locate the drain hose and water supply hoses.
3. STEP 3: Drain the washing machine of water.
4. STEP 4: Remove a drain hose clog.
5. STEP 5: Remove a drain pump clog.

How do you fix a washing machine that won’t drain water?

What to Do When Your Washing Machine Won’t Drain

1. Perform a Master Reset. Unplug your washer for about one minute.
2. Test the Lid Switch Assembly.
3. See if the Drain Hose is Kinked.
4. Check the Drain Hose or Pump for Clogs.
5. Clean out the Coin Trap.
6. Check the Water Level Control.
7. Schedule Washing Machine Repair.

How do you clean the drain pump filter on an Electrolux front loader?

Drain Pump Guard Filter

1. Open the pump guard panel.
2. Pull the emergency hose out.
3. Place the hose in a container and remove its cap.
4. Unscrew the pump guard filter.
5. Wash the filter in the sink to clean it.
6. With the filter out, check the pump impeller.
7. Put the pump guard filter and emergency hose back into the machine.

How do I drain the water out of my AEG washing machine?

Turn off the appliance. Open the door to the fluff filter and place the drip tray underneath. Empty any water out of the machine by opening the drain hose next to the filter. Remove the filter by turning it anti-clockwise (several times firmly by hand).

Where is the drain plug on my Electrolux washer?

Drain Plug and Filter This should be located somewhere near the bottom of your washing machine, depending on which model you have.

How do I get the water out of my washing machine that won’t drain?

What does the E20 code mean on an AEG washing machine?

Aeg electrolux washing machine e20 error The AEG E20 (or E21) fault code is typical of older AEG washers. The E20 code signals slow draining. The E20 – E21 codes mean that the draining has stopped.

Why is my AEG Electrolux not draining water?

It means that the machine is not draining water correctly. Check the drain hose, to see if it is kinked or folded over. It could also be that the drain pump or drain hose are clogged.

Why do I get an E20 error code?

Ok E20 is a draining error code. What you need to do is take the filter out again but this time with the filter out look inside the pump chamber and at the back you will see the impeller X shape. Make sure theres nothing jammed up in there stopping the impeller from turning.

Is the AEG washing machine a certified repair?

AEG has been producing high-quality machines that wash with a super clean result. AEG will not let you down a well-known slogan. As your AEG washing machine age, the chance of failure increasing. The machine is a certified AEG repair and regularly repairs washing machines with an E20 fault.