How much is a 1984 Honda 250R worth?
Values
| Excellent | $2,050 |
| Very Good | $1,200 |
| Good | $670 |
| Fair | $295 |
| Poor | N/A |
How fast is a Honda 250R?
The Honda 250r was one of the slowest of the 250’s produced. Top speed stock was around 65mph. It made around 29-32 hp in stock form.
How fast does a 250R three wheeler go?
Honda ATC250R
| Manufacturer | Honda |
|---|---|
| Engine | 246 cc (15.0 cu in) liquid-cooled two-stroke single |
| Bore / stroke | 66 x 72mm |
| Compression ratio | 142 – 170psi |
| Top speed | < 60 Mph |
How much is a 1986 250r worth?
Values
| Excellent | $1,705 |
| Very Good | $1,175 |
| Good | $610 |
| Fair | $265 |
| Poor | N/A |
How much is a Honda TRX 250?
2021 Honda TRX250X • $5,049 And new for 2021, fresh colors and graphics that are as much fun as the ride itself.
What was the top speed of a Honda XR250R?
The Honda XR250R was an air cooled single cylinder four-stroke Enduro motorcycle produced by Honda between 1981 and 2008. It could reach a top speed of 87 mph (140 km/h). Max torque was 17.48 ft/lbs (23.7 Nm) @ 6000 RPM. Claimed horsepower was 22.8 HP (17.0 KW) @ 7500 RPM.
How do you change the piston on a Honda CR80?
Apply engine oil to the piston pin hole and connecting rod inner surface. Install the piston with the ‘‘IN’’ mark toward the intake side and insert the piston pin through the piston and connecting rod. Install new piston pin clips into the grooves in the piston pin hole. Make sure that the piston pin clips are seated securely.
When did the Honda XR250R’84 come out?
The XR250R’84 was sold in 1984 in Flash Red. The number plate panels were yellow. The seat and tool bag were blue. The fork boots were black. The bike had a front hydraulic disc brake. The front wheel was 21″ while the back was 17″. The bike had a Pro-Link suspension and a plastic gas tank.
What was the difference between 1982 and 1984 Honda ATC250R?
The 1983+1984 ATC250R (2nd gen) incorporated many improvements over the prior 1982 model, mainly with the introduction of Pro-Link suspension, folding foot pegs, a larger fuel tank, slightly longer travel suspension in front and rear, and other improvements.
What was the top speed of the Honda ATC 250R?
This new power unit was a two stroke with notably increased power from the same capacity, a 6-speed transmission was also added meaning the top speed of the final iteration of the ATC 250R was a hair-raising 70+mph. By the mid-1980s the writing was on the wall for three-wheelers.
How big is the piston on a Honda 4 stroke engine?
A: A standard sized piston is fitted in a new engine. So if you have a 52mm cilinder, you will have a 52mm piston. Over time the cilinder will wear out and to ensure keeping a proper fit, you will install a oversized piston. These have the sizes x.25 , x.50 , x.75 and a round number after the x.75.
What kind of bike is the 84 CR250R?
The ’84 CR250R was the first of the “modern” era bikes, with water-cooling, linkage rear suspension, power valve-controlled exhaust port and front disc brakes – all the underpinnings of a current 250cc two-stroke. As such, it’s a popular choice for VMX enthusiasts as it can be competitive in both the pre-85 and pre-90s classes.
What kind of engine does a Honda CR250R have?
– Liquid-cooled two-stroke single-cylinder engine with 66.4mm x 72mm bore and stroke and 8.5:1 compression ratio. – Air intake boot is shaped for direct airflow, contributing to strong low-speed engine performance. – Foam gasket between airbox and air boot for better sealing and airflow management.