How to reset the theft system in a Pontiac Grand Prix?

Enter the vehicle and insert the ignition key into the ignition. Turn the ignition to the “ON” position but do not start the engine. Wait 30 seconds and start the engine. Verify that none of the security lights on the dashboard are flashing or illuminated.

Who is the owner of the Pontiac Grand Prix?

2004 Pontiac Grand Prix Owner ManualM GENERAL MOTORS, GM, the GM Emblem, PONTIAC, the PONTIAC Emblem and the name GRAND PRIX are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed.

Is the Pontiac Grand Prix a registered trademark?

GENERAL MOTORS, GM, the GM Emblem, PONTIAC, the PONTIAC Emblem and the name GRAND PRIX are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed.

How to reset the anti theft system in a Ford?

1 Insert the key into the ignition and turn it on to the position where the accessories are activated but not the engine. 2 Leave the key in this position for at least 10 minutes. 3 Check the anti-theft light again. 4 Now try to start the engine. 5 Repeat the process at least a couple of times if it does not work the first time.

When does the anti theft system car wont start?

If the engine does not respond or dies immediately after cranking up, leave the key in that position for 10 minutes. When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

How to deactivate the anti theft system on GM cars?

How to deactivate the anti-theft system on GM cars 1st WAY TO FIX IT ALL THESE STEPS MUST GET DONE USING YOUR CAR KEY. 1. lock the door 2. unlock the door 3. open it 4. shut it 5. lock the door again 6. wait about 20 seconds • This will shut the alarm off and reset the system.

How do you reset the anti theft system?

Insert the key into the door lock, on the driver’s side door. Turn it on, but don’t turn it back. Instead, hold the position for 40-60 seconds. This indicates to the system that you have the right key. Also, do the same by turning the key in the opposite direction and holding the position.

How to bypass factory theft on a GM vehicle?

This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle. You can get this kit from New Rockies.com . I came across this site surfing the net when I was having a similar issue on a GM vehicle.

How to reset the radio antitheft code on your Honda?

1-You must turn the ignition switch to the ON position. 2-Then you turn ON the radio and make sure the display is showing the word “CODE”. If you do not see this message, remove the backup fuse for 60 seconds or longer, and then go back to the first step. 3-Turn OFF the radio.

Why does my car radio keep asking for a code?

Whenever power is disconnected from the radio, it will ask for a radio code. In this episode of Proctor Car Tips, Rocky at Proctor Honda gives a quick car tip about your Car Radio. He speaks on why the Radio code comes on in your car, what to do when it does, and how to find the codes.

How to solve the anti theft system car wont start?

It is another way to solve the problem of anti theft system car wont start. Disconnect the positive terminal of the battery for a minute or two. Reconnect it and make sure that both the anode and cathode terminals are tightly attached. It will reset the computer system and your car is likely to kick off.

How do you find the anti theft code on a Jeep Wrangler?

1. Call 1-800-448-0944 2. Request anti-theft code. 3. State dealer code. 4. State radio serial number. 5. State VIN 6. The 4-digit anti-theft code will be provided. Eastern Time Monday through Friday. 1. Ignition in the run position. 2. Press the ON/VOL control.

How do you reset the anti-theft system?

The keyless entry remote and the ignition key are required to reset the anti-theft system. Exit the vehicle and stand next to the driver’s side front door. Close all of the vehicle’s doors. Press and hold the lock and unlock buttons on the keyless entry remote until the horn honks once and the lights flash briefly.

How do I reset the PassLock on my car?

1. Insert the master key with the black head into the ignition lock cylinder 2. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine.

How do I enter an anti theft code on my Radio?

A four digit security code is required in order for the radio to function: The key must be in the “RUN” position. Press the “ON/VOL” control button. The word “CODE” or ” Please enter Anti-Theft Code” will appear on the display.

What to do if your Pontiac Grand Am wont start?

Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. I created this channel to help people with small maintenance and repairs.

How to reset the OBD II drive cycle?

Decelerate without using the brake (coast down) to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute. Restart and accelerate to 40-55 MPH at 25% throttle and maintain speed for two minutes.

How long does it take to reset engine control module?

After a few minutes all the old data should be reset so plug the fuses back in and turn your vehicle back on. You will want to leave your vehicle at idle for at least 10 minutes which will give your ECM enough time to “learn” any new modifications installed on your vehicle.

How to decelerate a General Motors OBDII drive cycle?

Decelerate with using the brake [or the clutch!] by coasting down to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute. General Motors (specific) OBD II Drive Cycle Performing a GM OBDII Driving cycle: Cold Start.

How to reset the OBD II Diagnostic monitor?

Why are my Pontiac Grand Am security lights not turning off?

The theft deterrent is disabling the starting of the vehicle because you have a problem with it. Your vehicle has what’s called ‘Passlock’. There is a sensor inside the ignition cylinder that has an electronic password. And i had read that if it is the ignition then the lights would not turn off.

Why is the security light on on my Grand Prix?

You cannot just turn it off unless the problem is fixed. The security light is on because you have a problem with your Passlock theft system. There are temporary fixes, like doing a re-learn of the theft deterrent, but the problem will come back. Most likely, you need a new ignition cylinder. Those are what usually go bad on the Grand Prix cars.

How to bypass the PassLock sensor on a 2002 Pontiac Grand Am?

This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.

How to fix a Pontiac Grand Am PassLock sensor?

Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks. I continuously have to wait until the light stops blinking….

What to do when your Pontiac Grand Am won’t start?

To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset. Then I turn the key off and then back to start. It works every time but the 12 minute wait is a pain in the ass.

How to turn off GM PassLock security Telltale?

Here it is in it’s entirity. Turn ON the ignition, with the engine OFF. Attempt to start the engine, then release the key to ON (vehicle will not start). Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF. Turn OFF the ignition, and wait 5 seconds .

Is there a way to bypass GM PassLock?

At NEWROCKIES Inc., we’ve designed our PRO Bypass Module with the specific purpose of bypassing faulty GM VATS, Passkey and Passlock security systems IN FULL.

What to do if your car anti theft light is not blinking?

Leave the key in position for about 10 – 15 minutes. Step 3: Check the anti-theft light again. If it’s no longer blinking, turn the key back to the Off position and allow it to set for a minute or two. This gives the system time to reset or you won’t be able to start your car. Step 4: Start the engine. Attempt to start your engine.

How to repair a Grand Prix Impala 2006-2008?

Access our free Firing Orders Repair Guide for Grand Prix, Impala 2006-2008, Monte lo 2006-2007 through AutoZone Rewards. These diagrams include: Access our GrandPrix, Impala 2006-2008, Monte lo 2006-2007 Firing Orders Repair Guide by creating an account or signing into your AutoZone Rewards account.

What do you need to know about GM vehicle theft deterrent?

Connect a battery charger to the battery to ensure power is available while programming. Both the IPC/BCM and PCM must be working and communicating with each other. 1. Turn ignition on. 2. Attempt to start the engine, and then release the key to the “ON” position. 3. Observe the “SECURITY” indicator light.

How does the anti theft system work on a Pontiac Grand Prix?

The anti-theft system in a Pontiac Grand Prix is designed to prevent the vehicle from being stolen or operated by an unauthorized user. When the system senses an unauthorized entry into the vehicle it will honk the horn at one-second intervals for 60 seconds.

How to bypass vats, Passkey and PassLock security systems in GM?

It can be VATS, Passkey or Passlock anti theft system that is going bad causing your issue. I am going to share a secrete with you on how you can bypass these systems with very little effort. This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle.

Can a GM security bypass kit be installed?

This GM security Bypass kit will work for several GM, Oldsmobile, Chevy, Pontiac or even Buick vehicles on the street today. I was surprised to see how easy it was to install with very little effort.

How can I disable the alarm system on a 1997 Jeep Grand?

If there is the Honda added security box installed at the lower left side of the kick panel turn the ignition key to the on position. Locate the small button on the box and hold it down for 90 seconds and the alarm will bypass. Call to the dealer, this was their response: With the ignition key try to start the vehicle.

What should I do if my car alarm is not working?

Roll the windows up and lock the car. Let the car sit for five minutes while being more than 10 feet away then unlock the car. Do not disconnect the car battery because the alarm system has a rolling code that may get mixed up when reconnecting the battery.

How can I Reset my Volkswagen security system?

Volkswagen Security System Reset. To deactivate the anti-theft system use the unlock button on the remote key. Unlock the driver’s door using the key and then switch the ignition switch to the on position. If that doesn’t work exit the vehicle and roll up all windows, then use the key to lock the driver’s door.

Is there a way to reset a factory car alarm?

Utilize common tricks. Factory car alarms have some simple reset protocols to help turn off an alarm. Most of the tricks rely on using the key in the door; simply put, a lot of factory car alarms have a door sensor, so working with the door might be the go-to for a quick fix.

What happens if I disable my car alarm?

Disabling a car alarm can be a temporary fix before seeking professional auto assistance. However, keep in mind, car alarms are meant to be anti-theft, and when tampered with, some systems prevent a vehicle from starting as a security measure. Understand the basics of an alarm system. Alarm systems consist of a few components. Control unit.

How to troubleshoot the air conditioning in a Pontiac Grand Prix?

See if the problem is as simple as a blown fuse. It is probably a blown fuse if the temperature controls on the dashboard seem to work correctly but have no effect on the air. Find the fuse box in a Pontiac Grand Prix inside the glove box.

Where is the AC fuse on a Pontiac Grand Prix?

Find the fuse box in a Pontiac Grand Prix inside the glove box. Locate a small bin on the right side of the glove box and open it. The fuse controlling AC will be in location 28.

What to do if your Grand Am won’t start?

When your Grand Am turns over but won’t start it maybe your anti-theft security system. When the security light blinks, the car won’t start. You must do a simple reset. The procedure in this video is what worked for us. Use of the free information in this video is at your own risk.

What to do when your car alarm wont work?

After inserting the key into the driver’s door lock, turn the key to unlock, lock and then lock position again. Then, turn it again to the unlock position and the alarm is likely to be disabled now. Run the car for at least 10 minutes after cranking the engine to allow the car to reset the alarm. Keep the Car Thieves Away with these 5 Tips!

Why does my GM theft lock radio lock up?

GM Theftlock radios are designed to lock up automatically when the vehicle’s battery dies or becomes disconnected, though an electronic malfunction could also cause the Theftlock function to activate.

How do I relearn GM theft deterrent system?

If the key signature transmitted is acceptable to the theft deterrent control module, the theft deterrent control module will transmit fuel enable password to the PCM. If the fuel enable password is correct, the PCM will start the vehicle. To perform a relearn on a Passkey III system, make sure there is a fully charged battery in the vehicle.

What to do if your PassLock system does not work?

If it does not start with the second key or you do not have one, you may be able to take the key itself to the dealer to see if it is actually transmitting properly. If you have 2 keys and it does not start, try this procedure. The Passlock system has two basic relearn procedures—a ten-minute procedure and a thirty-minute procedure.

How do I unlock my GM TheftLock radio?

Unlocking your Theftlock radio will require you to enter a unique 4-digit numerical code. Before you can do this, however, it will be necessary to write down two separate 3-digit numbers, which you’ll get by punching a series of buttons on the radio’s interface.

How to reset PassLock reset system on Chevy?

1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.

How do I Turn Off the anti theft light in my car?

Insert the key into the ignition and turn it to the on position, which activates your accessories but not the engine. Leave the key in position for about 10 – 15 minutes. Step 3: Check the anti-theft light again. If it’s no longer blinking, turn the key back to the Off position and allow it to set for a minute or two.

How to disable the anti theft device in your car?

Hold the key in this position for 20 to 30 seconds. This lets the system know you have the correct key, and it can allow you to bypass the alarm system. Some vehicles recognize the key simply by turning the key back and forth in the door lock key cylinder. Tip: Try turning the key both ways fully to disable the anti-theft system.

Why does my car anti theft system activate?

A car’s anti-theft system may activate if your key fob battery is dead and hasn’t disabled the system. Make sure the battery is installed correctly in your key fob. If the battery is correctly installed, replace it with a fresh battery and try again.

What should I do if my car wont start?

When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

Where is the fuel pump relay on a Pontiac Grand Am?

The fuel pump relay is #18 in the fuse box. Start with the car off, and have somebody else put the key in the cars ignition and attempt to start the car while you listen to the relay. If you can hear this relay make a “clicking” noise as the car attempts to start, then it is working properly.

Why is my fuel pump reset button not working?

Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc. As a first step best to see if there are any stored trouble codes that could point directly to the fault.

Why is the starter not turning on my Pontiac Grand Am?

If you can hear the starter motor turning but the engine isn’t turning (look at the belt) then the starter may not be engaging (in your car I believe this means that you must replace the whole starter). You can remove and test your starter to confirm whether or not the solenoid is engaging the starter.

How long does it take to turn off a GM security light?

Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2. Turn the ignition switch to the “OFF” position for 30 seconds. 3.

What do you need to know about GM security module?

Connect a battery charger to the battery to ensure power is available while programming. Both the IPC/BCM and PCM must be working and communicating with each other. Observe the “SECURITY” indicator After 10 minutes the “SECURITY” indicator light will turn off.

Is it normal for the security light to go off when the engine is running?

After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off—this is normal. Depending on the system, replacement of key components will necessitate that a relearn procedure be completed.

How long does it take for a security light to go off?

Which one you use depends on the system and what components have been replaced. The ten-minute procedure involves trying to start the engine. If nothing happens or the engine starts and dies, the security light will be flashing. Leave the key in the On position and wait ten minutes. The flashing light should go off or illuminate without flashing.

How can I bypass the car theft alarm?

It is likely to turn off the light and start the car. Remember that this is the state where the vehicle is on but the engine is off. All the necessary components like the radio and dashboard lights will be powered up, which makes it possible to bypass the theft alarm. When you are outside the car.

When does anti theft system lock the steering wheel?

Sometimes, the anti-theft system locks the steering wheel and does not let the key turn inside the slot. This annoying problem is mostly exclusive to Hondas. It mainly happens when you move the steering wheel after turning off the car. It locks the wheel in that position and does not let you move it next time you try to switch on the car.

How do you reset the TPMs on a Pontiac?

Using the keyless entry (key fob), press and hold the lock and the unlock buttons simultaneously until the horn sounds. Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR.

How to reset the sensor for an ABS on a Pontiac Grand Prix?

by Daniel Valladares. The only tool required to reset the sensor for the ABS system on a Pontiac Grand Prix is a socket wrench. Because the ABS system sensor uses the electrical system, resetting the electrical system will reset the ABS system.

Where was the Pontiac Grand Prix GTP last serviced?

No accident or damage reported to CARFAX… 1st owner purchased on 08/20/04 and owne… Last serviced at 190,560 miles in Berlin… 1st owner drove an estimated 27,182 mile… No accident or damage reported to CARFAX…

How much horsepower does a Pontiac Grand Prix have?

The new Grand Prix sought to deliver performance as attention-getting as its styling, with increased installation percentages for manual transmissions and engine options up to the 390 hp (290 kW) 428 HO.

What was the performance of the 1973 Pontiac Grand Prix?

1973 Pontiac Grand Prix All A-bodies, including the Grand Prix, were redesigned for 1973. This generation was larger and heavier, due partly to the federally mandated 5 mph (8.0 km/h) crash bumpers. Although large V8s were still available, the performance was on the decline due to new emissions control systems.

How to permanently disable and remove GM security systems?

GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently. This is what NEWROCKIES Inc is all about.

Can You disable the PassLock on a GM car?

The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.

How long does it take for PassLock sensor to turn off?

•Observe the security light located in the instrument cluster, after approximately 10 minutes the security light will turn OFF. Turn OFF the ignition, and wait 5 seconds. •The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.

How do you reset a locked GM TheftLock radio?

This is the most common code used by GM personnel to reset locked Theftlock radios. Key in each number carefully, then hit the # sign to send your request through. Under normal circumstances, a locked Theftlock radio must be reset by a licensed GM dealer, who uses a special code known only by dealership personnel.

How to reset PassLock 3 security system on Chevy?

But here are some more articles to help Passlock III reset procedure, reset security system on chevy, buick, oldsmobile, cadillac, pontiac, saturn, hummer. Passkey III Reset procedure. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time.

When was the last year for the Pontiac Grand Prix?

2008. 2008 was the Pontiac Grand Prix’s last year as the sedan. For 2008, Pontiac did not offer the GT trim, but continued to offer both a base and GXP trim. The base trim is offered with a 200 hp (150 kW) V6 engine and 16 in (41 cm) wheels. Several new colors were also added for the 2008 model year.

What did the Pontiac Grand Prix look like in 1964?

The 1964 Grand Prix received minor appearance changes from the 1963 edition. Those included a revised grille (based on the 1964 Bonneville/Catalina) with new “GP” logos and rear deck trim with new taillights, still hidden, again following the shape of the other big ’64 Pontiacs.

Is there an anti theft system on a GM car?

GM has used a variety of anti-theft systems on their vehicles. When you get a no start, intermittent start, or start then die, you should first determine which GM anti-theft system you have. Then diagnose the anti-theft system before you start replacing starting components.

Where is the transponder on a GM passkey?

This system uses a special key (PK3 stamped on the shoulder of the key) with a transponder under the rubber cover. The receiver module is located next to the lock cylinder. When the key is positioned next to the lock cylinder receiver module, it energizes the transponder which sends a coded signal to the receiver.

GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently. This is what NEWROCKIES Inc is all about.

What kind of power does a Pontiac Grand Prix have?

The standard 350 hp (260 kW) 400 cu in (6.6 L) V8 was revised to meet the new 1968 Federal and California emission regulations. Both optional 428 cu in (7.0 L) V8s received higher power ratings of 375 hp (280 kW) for the base version and 390 hp (290 kW) the HO. Interior trim only received minor changes from 1967 aside from revised door panels.

When did the Pontiac Grand Prix come out?

In this article, we consider the sixth-generation Pontiac Grand Prix, produced from 1997 to 2003. Here you will find fuse box diagrams of Pontiac Grand Prix 1997, 1998, 1999, 2000, 2001, 2002 and 2003, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

Where can I get a Pontiac Grand Prix ignition switch?

Check out my gear head channel. All the videos here are power related, from lawn mowers, snow blowers and my ever expanding fleet of automobiles. I specialize in trash picked equipment and finding new life in them with other than intended purposes.

Where is the fuse box on a Pontiac Grand Prix?

Pontiac Grand Prix (2004-2008)…>>. Cigar lighter / power outlet fuse in the Pontiac Grand Prix is located in the Instrument panel fuse box (see fuse “CIG LTR”). It is located in the glovebox, behind the cover on the right.

What to do if your ignition key won’t work?

In this case the ignition lock must be replaced. Step 7 – In extreme conditions such as high mileage or a key chain adorned with many ornaments can wear the tumbler which causes the key not to work. If the door key is same as the ignition key, the door tumbler can be removed and a key made if no security chip is installed, (older cars).

How do you enter a car with a keyless entry?

Exit the vehicle and stand next to the driver’s side front door. Close all of the vehicle’s doors. Press and hold the lock and unlock buttons on the keyless entry remote until the horn honks once and the lights flash briefly. Enter the vehicle and insert the ignition key into the ignition.

At NEWROCKIES Inc., we’ve designed our PRO Bypass Module with the specific purpose of bypassing faulty GM VATS, Passkey and Passlock security systems IN FULL.

Why does my Pontiac Grand Am Not Start?

I have been in the auto industry for more than 20 years and would like to share my knowledge with others. Due to how many vehicles I buy, sell, and repair I will be uploading new videos as I come across common and uncommon problems and simple maintenance. An error occurred while retrieving sharing information.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

How to replace the PassLock sensor on a GM car?

Find the three wires that connect the Passlock Sensor to the Body Control Module and substitute our circuit for the Passlock Sensor. Perform the “Relearn” Procedure so that our Body Control Module recognizes our new circuit. Go to Radio Shack and buy a Mini Terminal Block, and a package of 2200 ohm (2.2k-Ohm) resistors.

What kind of security system does a GM Truck have?

Here is a list of GM vehicles that have VATS, Passkey or Passlock security system built in from the factory. Trucks GMC/Chevy 1998-2006 S10/T10/Sonoma /Blazer/Jimmy 1998-2007 Suburban/Avalanche /Tahoe/Yukon 1998-2010 Sierra/Silverado 2004-2010 Colorado/Canyon 2002-2008 Trailblazer 2003-2006 SSR

What kind of security system does GM use?

VATS, Passkey or Passlock – are the core of GM security systems, have a short lifespan and they’re certainly more effective at keeping you from DRIVING your car than keeping someone from STEALING your car! GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently.

Is there a way to bypass GM security system?

Scouts Troop 980 of Utah cheers as their ’92 Olds Toronado is coming back to life. Thanks to the NEWROCKIES Full Bypass Module! How to FULLY bypass VATS Passkey and Passlock Security Systems in GM Cars. Has the dreaded GM Security system just hit you?

What to do if your anti theft system is locked up?

If the anti-theft system has locked up your engine, you won’t be able to start it. You’ll have to disable it with these steps. Step 1: Check for the anti-theft light. It’s located on your dash and will have a blue or red light. Step 2: Turn the ignition to the “on” position.

Why does my 2003 Grand Am Not Start?

My 2003 Grand Am sometimes wont start. I’ve noticed that when it wont start, the security light is flashing. To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset.

How to troubleshoot a GM 3.1L no start?

Important Tips And Suggestions. No Start Condition Basics. No Start 1: Checking For Spark. No Start 2: Checking For Fuel. No Start 3: Anti-Theft System Checks. No Start 4: Checking Engine Mechanical Condition. No Start Summary. Related Test Articles.

What causes the fuel pump to not start?

The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.

Why does my Pontiac Grand Prix not restart?

When I go somewhere and shut it off, sometimes it won’t resatrt. It doesn’t seem to matter what the weather is outside, it just does it when it feels like it. It seems to happen more when I am stopped at a gas station, (not getting gas)- as crazy as that sounds. When it won’t restart, it will turn over and crank and act like it’s not getting fuel.

What causes Trac off on a Pontiac Grand Prix?

The “Trac Off” failures are usually a wheel speed sensor which is off the BCM not the ECU. — It seems like it might be a flaky ECU but I’m just guessing. 10 people found this helpful. Have you checked the fuel pressure? Could be ECU as mentioned above or possibly dirty injectors or fuel pump.

Why does my car not start when stopped at a gas station?

It seems to happen more when I am stopped at a gas station, (not getting gas)- as crazy as that sounds. When it won’t restart, it will turn over and crank and act like it’s not getting fuel. We have checked the coils, fuel pressure regulator and just now replaced the fuel pump.

What is the code for a Pontiac Grand Prix?

It is often accompanied by P0442. See Pontiac Grand Prix P0442 OBDII Code for more. P0420 is another common trouble code that accompanies P0446. P0446 code will typically not be accompanied by any noticeable symptoms. The service engine soon light will come on, but that is usually about it.

What to do if your Grand Prix has p0446 code?

Here are the most common Grand Prix P0446 fixes: Of all the items listed above, it would be wise to start with the gas cap and work your way to the fuel tank, since the gas cap is far and away the easiest and least expensive items to replace on here. Here’s a great video on how to test your gas cap.

What’s the difference between p0480 and P0 482?

NOTE: P0480 speaks of the basic circuit, however codes P0481, and P0482 relate to the same problem with the only difference is they relate to the different fan speed relays. Check engine light (malfunction indicator lamp) illumination and code P0480 set

Who is the owner of the 2008 Pontiac Grand Prix?

2008 Pontiac Grand Prix Owner ManualM GENERAL MOTORS, GM, the GM Emblem, PONTIAC, the PONTIAC Emblem, and the names GRAND PRIX, and GXP are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without notice.

When was the last time I serviced my Pontiac Grand Prix?

Last serviced at 96,882 miles in Sarasota, FL on 01/27/21 • Vehicle serviced • Battery replaced • Battery/charging system checked. Mileage: 97,317 miles Body Type: Sedan Color: Silver Engine: 6 Cyl 3.8 L

GENERAL MOTORS, GM, the GM Emblem, PONTIAC, the PONTIAC Emblem, and the names GRAND PRIX, and GXP are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without notice.

When was the last serviced Pontiac Grand Prix?

Purchased on 12/16/05 and owned in CA until 05/24/21. Driven an estimated 9,810 miles/year. Last serviced at 151,582 miles in Fairfield, CA on 06/09/21 • Vehicle serviced • Left front window switch replaced.

How many miles does a Pontiac Grand Prix have?

Mileage: 119,184 miles Body Type: Sedan Color: White Engine: 6 Cyl 3.8 L No accident or damage reported to CARFAX. 1st owner purchased on 12/08/06 and owned in WI until 05/10/10 • 2nd owner purchased on 09/03/10 and owned in WI until 04/16/14 • 3rd owner purchased on 08/14/14 and owned in WI until .

Who was the first owner of the Pontiac Grand Prix?

1st owner purchased on 06/29/06 and owned in PA until 10/21/16 • 2nd owner purchased on 03/10/17 and owned in PA until 06/03/21. 1st owner drove an estimated 10,859 miles/year • 2nd owner drove an estimated 1,528 miles/year.

Where do I find the trouble code on my Pontiac?

These are listed in numerical order for easy searching. When retrieving Pontiac trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.

What are the misfire codes for GM 3.8L?

Here are some of the most common symptoms of a misfire condition on your GM 3.8L: The check engine light will be on. One or more misfire codes will be stored in the car or mini-van’s computer memory (if OBD II equipped). P0300 Random Cylinder Misfire. P0301 Cylinder #1 Misfire. P0302 Cylinder #2 Misfire. P0303 Cylinder #3 Misfire.

When do you need to clear an error code on a Pontiac?

No matter what kind of Pontiac vehicle you drive, at some point you’re sure to come across a situation where the check engine light goes on and will require the error code to be cleared out. Error codes are triggered when your Pontiac’s computer detects a mechanical issue with the car and then illuminates the check engine light.

What was the name of the 1963 Pontiac Grand Prix?

1963 Pontiac Grand Prix Sports Coupe For 1963, the Grand Prix received revised sheet metal shared with other full-size Pontiacs, but with its own squared-off roofline with a concave rear window that contrasted with the convertible-like roofline of the 1962 Grand Prix and continued on the 1963 to 1964 Catalina and Bonneville.

What kind of carpet does a Pontiac Grand Prix have?

The bucket seats were upholstered in Morrokide vinyl, while nylon loop-blend carpeting covered the floor and lower door panels. The center console-mounted transmission shifter included a storage compartment and a tachometer.

What kind of car is the Pontiac Grand Prix?

Pontiac gives the base Grand Prix engine more horsepower and adds a racy pace-car replica as a special-edition model for 2000. The Grand Prix coupe is the foundation for Pontiac’s entry in NASCAR stock-car competition, and a modified production Grand Prix paced the Daytona 500 last February.

What was the wheelbase of the 1978 Pontiac Grand Prix?

1978 brought a downsizing of the Grand Prix and the other A-bodies. The 1978 GP was about 1 ft (0.3 m) shorter and 600 lb (270 kg) lighter than the 1977 model with an overall length of 200 in (5,100 mm) and a 108 in (2,700 mm) wheelbase. For the first time in Grand Prix history, a V8 engine was not standard equipment.

Can a GM security system be moved to another car?

Newrockies inc proudly manufactures its modules with top quality electronic components. No more risks of remaining on the road. Universal. The same module works with over 100 different GM and Isuzu cars – you can even move it on your next car! Trusted.

How to fix a car that won’t start when you turn the key?

How to fix car that wont crank when you turn the key, no sound or click. How to jump start a car, check the starter, and wire bypass trick. DIY car repair with Scotty Kilmer, an auto mechanic for the last 50 years. Thanks for watching! 1. Bluetooth Scan Tool: http://amzn.to/2nfvmaD 2. Cheap Scan Tool: https://amzn.to/2D8Tvae 3.

Security system has been malfunctioning for a few years. When security light is on solid all the time, the car starts every time. That is because the security system is disabled. Only when the security system is enabled, security light off, the car has starting issues. Best way to fix is to permanently disable/disconnect passlock system.

When does a GM TheftLock radio lock up?

If you own a late ‘90s or early 2000s model General Motors vehicle, you may have found out the hard way that your factory Theftlock radio is programmed to lock up if there’s any disruption in the battery.

Where do you find the car alarm system?

Find the alarm system. If you have a factory car alarm, check in your owner’s manual as a guide. The alarm system is usually under the hood near the steering wheel. If you have an after-market car alarm, it may be installed in any part of the car, but companies usually install them under the steering wheel.

How can I fix the alarm on my car?

Fix an alarm that starts when you turn the car on. You could need a new battery. Disable the alarm by removing the alarm fuse, and then bring the car to the shop. They can check your battery and move on from there if the problem is the alarm system. Diagnose an alarm that never sets. Lock your car electronically using the remote, if you have one.

Where is the factory alarm on my car?

How to replace oil pan on Pontiac Grand Prix?

Here is a video on how to replace the oil pan on a Pontiac Grand Prix with the 3.8l engine. This process is the same for any wbody vehicle like the Chevy Impala, Monte Carlo, Buick Regal with the GM 3800 Series II or Series III engine supercharged or naturally aspirated. If playback doesn’t begin shortly, try restarting your device.

Is the Pontiac Grand Prix a good car?

If you judge a car by it being affordable and economical to drive, then the 1988 Grand Prix was a good car, in fact, it won Motor Trend’s Car of The Year for 1988.

When did the Pontiac Grand Prix go out of production?

Building a reputation with those incredible models, Pontiac slipped with the rest of the industry as the Oil Crisis hit, soldiering on through to the ’90s in relative mediocrity. Unfortunately, from there things didn’t get better for Pontiac, leading to their death as a brand in 2010 in order to save GM from bankruptcy.

How can you save money on a used Pontiac Grand Prix?

How can you save money on a used Pontiac Grand Prix? iSeeCars analyzes over 25 billion data points to help you find the best deals. See more ways to save. Does car color affect the price of a used Pontiac Grand Prix? iSeeCars analyzes over 25 billion data points to help you find the best deals.

How does car color affect the price of a Pontiac Grand Prix?

See more ways to save. Does car color affect the price of a used Pontiac Grand Prix? iSeeCars analyzes over 25 billion data points to help you find the best deals. See more ways to save. Exterior Color: Dk.

What kind of car was the first Pontiac Grand Prix?

Early models were available with Pontiac performance options, including the factory-race Super Duty 421 powertrain installed in a handful of 1962 and 1963 cars. The first Grand Prix was a Catalina hardtop coupe trimmed to standards similar to the larger top-line Bonneville, with a distinctive grille and taillights.

What should the MPG be on a Pontiac Grand Prix?

TPS is pretty inexpensive and quite simple to change. Also forgot to mention that when it was on, the car was using a ton of gas. MPG went from 23 to 15. If you are seeing none of these symptoms then don’t throw money at it. 6 people found this helpful.

Do you need to know before you disconnect a car battery?

So, before you disconnect a car battery; there are things you need to know. Battery voltage MUST be maintained to the (PCM) and other modules; while the battery is disconnected. NEVER: disconnect the car battery; while the engine is running or the ignition key is turned on.

How long does it take for car battery to re-gain charge?

If the switch is in the on position turn the switch off, jump start or charge the battery. The battery should re-gain its state of charge after about 15 minutes of driving. Once all of the door have been closed check the interior and dome lights, these lights should turn off after a short amount of time.

What’s the best way to disconnect two batteries?

In an instance where you have two batteries and you need to disconnect both, you can use knife blade disconnect switches. You can use one switch to disconnect one battery and another to preserve the other battery. These switches use a knob that turns clockwise or anti-clockwise to disconnect or connect the battery.

Why is my GM keyless remote not working?

Test the locking mechanism on the transmitter. If it works from that distance, step back another 20 feet (40 feet in total) and try it from there. If you are noticing it not working, you may have to restart the sync cycle over again. It may also indicate the battery is low. Determine if your car has a VIC (Vehicle Identity Check).

What to do if you forget to turn off keyless entry?

Turn the ignition switch to the ON (one more click forward) position in order to exit the keyless entry transmitter mode. If you forget to do this step, it is likely that your car will not unlock/lock properly. Operate the transmitter functions in order to verify correct system operation. Step out of your car, and go as far as 20 feet.

What should I do if I Lost my GM key?

If you have lost your keys, or have just bought a new car, you will need to program a new keyless remote. There are three broad categories when it comes to GM keyless remotes: pre-2007, 2007–10 with VIC, and 2007 – 10 without VIC. If your car is a GM post-2010 model, you should contact your nearest car care professional.

How does the keyless entry work on a Pontiac?

Press and hold the Unlock and Lock buttons on the keyless entry for approximately 15 seconds. When the chime sounds, the remote is programmed. The keyless remotes for Pontiac vehicles are not compatible with other vehicles and vice versa. The remote you are attempting to program must be specifically for the Pontiac vehicle.

Is there a keyless entry remote for a Pontiac Solstice?

Most Pontiac keyless entry remotes, such as the Grand Am, Grand Prix, G6 and Solstice, must be programmed by the dealer. However, some Pontiac vehicles have customer-programmable keyless remotes. Close all of your Aztek’s doors. Press and hold the “Unlock” button on your driver’s side door control panel.

Why does my key fob not work on my car?

This video is based on the reasons as to why the key fob or keyless entry doesn’t work completely as in operating the lock, unlock, panic, trunk and door features all together. If only one button doesn’t work or your vehicle doesn’t start, well that can be relating to another issue.

How do you turn on a radio on a keyless entry?

Press and hold the Unlock and Lock buttons on your keyless entry for 30 seconds. When you hear a warning chime, the remote is programmed. Open the interior fuse compartment door. Examine the diagram on the back to find the fuse labeled Radio. Remove this fuse from its slot. Insert your key into the ignition.

How do I disable OnStar on my car?

Step 1: Open the trunk of your vehicle and lift floor fabric. You should open your trunk and remove the floor fabric covering the spare tire and tub cover. Step 2: Remove the tub cover and spare tire. Lift the fabric covering on the bottom of your trunk to reveal your spare tire and tub cover. Not all vehicles will have these.

What do you need to know about OnStar?

OnStar is a subscription-based service that provides remote vehicle diagnostics, communications, security, and other features for vehicles. The company is a subsidiary of General Motors, and is popular for capabilities like turn-by-turn navigation, hands-free calling, and as a surveillance device when your car or truck is left unattended.

How do you remove OnStar module box port?

Press the tab down on the cord end that connects with the module box port and pull the connector right out. These connectors are similar to landline telephone cord connectors and should be easy to remove. Step 7: Repeat for remaining connectors.

What happens to a GMC radio if battery dies?

Chevy and GMC vehicles both feature Theftlock radios which render the stereo inoperable to would-be thieves. The downside of the Theftlock system is that if your battery dies or becomes disconnected, you’ll need to enter the radio code to deactivate the Theftlock system.

How can I get my GM radio out of my car?

Phoning in for Your Radio Retrieval Code Dial 1-800-537-5140 to connect with GM’s toll-free radio hotline. Enter the numbers “106010” when prompted for a dealer access code. Punch in your vehicle’s 6-digit radio identification number when instructed. Write down the 4-digit radio retrieval code as it’s recited to you.

What causes a GM radio to lock up?

Take your car to a qualified GM mechanic or car radio technician to have them diagnose the source of the problem. GM Theftlock radios are designed to lock up automatically when the vehicle’s battery dies or becomes disconnected, though an electronic malfunction could also cause the Theftlock function to activate.

What’s the quarter mile acceleration of a Pontiac?

Please note that some 0-62 (0–100 km/h) times on this website are converted to 0 to 60 acceleration times. Bookmark us and keep checking back for Pontiac cars 0-60 mph updates, since we constantly upload new 0 to 60 mph and quarter mile statistics.

What are the 0 to 60 times on a Pontiac?

Please take into account that the Pontiac 0 to 60 times and Quarter mile data listed on this car performance page is gathered from numerous credible sources. There are a great deal of factors that affect the Pontiac cars 0-60 stats, so different sources may test the same vehicle and each may arrive at a unique 0-60 mph and quarter mile result. Zero

What is causing my 1997 Pontiac Grand Prix with a 3.8L non supercharged engine?

What is causing my 1997 Pontiac Grand Prix with a 3.8l non supercharged engine to keep giving me a p1406 dtc. I have Pontiac problems? Ask a mechanic for answers ASAP

How many times does a Pontiac go 60 mph?

to 60 times does not guarantee the accuracy of any of the Pontiac 0-60 mph times. Our car specs website is considered by many, to be the most easy-to-find directory for car statistics including classic cars, hybrid cars, luxury cars, muscle cars, sports cars and more!

What should I do if my car alarm does not shut off?

Remove the fuse. If the alarm shuts off, you have pulled the correct fuse. If the alarm doesn’t shut off, re-install the fuse and try another one until you find the correct fuse. Once the alarm has shut down, reinstall the fuse and see if this resets the system.

Can a key fob cause a car alarm to go off?

The key fob, also known as a car remote key, is a device which is used to lock/unlock your car doors and even start the engine with just a push of a button. Since the key fob also has controls linked with the car alarm system, a malfunctioning or faulty key fob can send an incorrect signal which may trigger the car’s alarm.

Why does my car alarm keep going off at night?

A bad car battery or low battery charge is a widespread problem for a car alarm that goes off during the night. If you hear the car alarm going off at night and the car battery is dead in the morning, the car battery may be bad.

What’s the best way to turn off a car alarm?

Step 2: Start the car. Put the key in the ignition and try to start the car. Almost all alarms, both factory installed and aftermarket systems, will shut off and reset when the car is started. Step 3: Use your key to unlock the driver’s door. This will usually turn off and reset the alarm.

Why does my car alarm keep going off?

Your car might have a very common problem. Mark shows you a trick he has used to stop this annoying condition. It only takes a few seconds and a few pennies so take a look. Loading…

What to do if your car alarm is tampered with?

Some car alarms, when tampered with, prevent a car from starting as an anti-theft function. If you remove the fuse and cannot start the vehicle, you will have to take the car to a mechanic or dealer. Press the “panic” or buttons on your keychain remote to stop the alarm. Because the “panic” button can sound the car alarm, it can also stop it.

When was the first Pontiac Grand Prix built?

The first 1997 Grand Prix was built on August 12, 1996. Promoted widely for its “wide track” appearance, the second generation W-body Grand Prix sold well. There were 3 trim levels available in 1997; the SE, GT, and GTP.

What are the most common problems with a Pontiac Grand Prix?

One of the most common problems that occur with the Pontiac Grand Prix and other GM vehicles is a burnt out window motor or a broken regulator. The driver’s window gets the most use and is usually the first to fail.

What kind of supercharger does a Pontiac Grand Prix have?

Pontiac G rand Prix GTP Eaton M90 Supercharger Oil Change Guide The GTP trim level of the Pontiac Grand Prix is equipped with the L67 version of the GM 3800 Series II engine with an Eaton M90 supercharger.

How to Reset the Theft System in a Pontiac Grand Prix. Press and hold the lock and unlock buttons on the keyless entry remote until the horn honks once and the lights flash briefly. Enter the vehicle and insert the ignition key into the ignition. Turn the ignition to the “ON” position but do not start the engine. Wait 30 seconds and start…

Is there a way to unlock a Pontiac radio?

This solution is an express one so you will forget that you ever had a trouble with the unlock code for your Pontiac radio. So the Pontiac radio code generator is now the first choice of many people around the world. Not only that, but it is the favorite tool of the Pontiac radio service workshops as well.

Do you need serial number for Pontiac radio code generator?

So everyone can benefit from it. Like the most expensive Pontiac radio service, this tool will require your serial number. So, once you have the Pontiac radio code generator and your serial number consider the job done. So you will get your Pontiac radio car unlock code before you know it.

How do you get a GM passkey 3?

Try the following procedure which is specifically for GM Passkey 3. 1. Insert a master key (black head) into the ignition switch. 2. Turn to the On position without starting the engine. The security light should illuminate and stay on. 3. Wait approximately 10 minutes or until the security light turns off.

How to turn off security light on passkey 3?

Try the following procedure which is specifically for GM Passkey 3. 1. Insert a master key (black head) into the ignition switch. 2. Turn to the “On” position without starting the engine. The security light should illuminate and stay on. 3. Wait approximately 10 minutes or until the security light turns off.

Where can I buy a 1994 Pontiac Grand Prix?

Call Spradley Chevrolet Hyundai s Internet Department today at 719-544-8162 and schedule your time to come in and test drive any of our new Chevrolet Silverado 1500, Impala and Suburban s or Hyundai Santa Fe, Tucson and Accent s. And don t forget, we have all makes and models of pre-owned to choose from.

Navigation