How to read Trouble Codes on 88-95 GM cars and trucks?
To read the trouble codes when your check engine light comes on on one of these old cars, you just need to put a paperclip in between two terminals, and then turn the ignition on, and the check engine light will flash the code, which you can interpret to find out what is wrong with your engine.
Why does my Chevy truck stall at idle?
Filter is not that old, and if plugged or if pressure regulator is malfunctioning, why do I never see fuel pressure at throttle body so much as waver lower than 12psi? Also, many times the lean condition will start just off idle so bad so that truck wil fall flat on its face and stall.
Why does my GMC Sierra stall at 30 mph?
Never threw a service engine light or a code and would readily re start. 2 weeks ago it quit at 30 mph, wouldn’t restart and SES lit up. Code indicated crank positioning sensor. Had it replaced and so far so good. If yours behaves as mine did it could be a while before you get a traceable code. I own a 1998 GM Sierra 5.7L 2wd automatic.
What happens when the throttle gets stuck in an open position?
When the throttle gets stuck in an open position than your vehicle will receive too much air and cause it to have a high or fluctuating idle. What are signs of a bad Throttle Position Sensor? Acceleration issues: A bad TPS may cause all sorts of power issues. Your engine may start up but it will have little to no power and it causes it to shut off.
What does GM OBD I trouble code chart mean?
GM OBD I Trouble Code Chart Code Description Code 12 No distributor reference pulse (diagnost Code 13 Oxygen sensor circuit open or no activit Code 14 Engine coolant temp sensor error (high t Code 15 Engine coolant temp sensor error (low te
What are the codes for GMC check engine lights?
P1245Intake Plenum Switchover Valve P1250Early Fuel Evaporation Heater Circuit P1257Supercharger System Overboost P1258Engine Coolant Overtemperature – Protection Mode Active P1260Last Test Failed SCC Or Theft Detected, Vehicle Immobilized
What are the symptoms of a bad ECM computer?
There are a few things that can tip you off that there’s a problem. Here are the four most common symptoms of a bad ECM computer: There are many reasons your Check Engine light can turn on. These range from emissions problems to faulty O2 sensors to problems with the ECM.
What are the GM trouble codes for 2008?
Here is what I have done since Aug. 2008 I have replaced the MAF sensor, air filter, knock sensor, fuel pump, coil, tps, fuel filter, distributor cap and rotor. But guess what I am still having the same codes in this order P0327,P0171, and P0174.
What causes a code 15 on a coolant sensor?
A failed coolant temperature sensor is the most common cause of a Code 15 A quick test for the coolant temperature sensor circuit from the ECM would be to unplug the temp sensor and watch the coolant sensor reading on the scan tool while jumping the harness side of the sensor connector.
What are the trouble codes for a 2000 Jeep?
2000 jeep limited 4.7 4×4…..just put in new timing chains and everything else in there is new also. Jeep ran fine before new stuff was put in and it does start good now but its running rough and showing codes now. It almost sounds as if there is a vacuum leak now since I can hear a sucking kind of…
To read the trouble codes when your check engine light comes on on one of these old cars, you just need to put a paperclip in between two terminals, and then turn the ignition on, and the check engine light will flash the code, which you can interpret to find out what is wrong with your engine.
When do you need an I-94 form?
An I-94 form is needed by all persons except U.S. Citizens, returning resident aliens, aliens with immigrant visas, and most Canadian citizens visiting or in transit. Air and Sea travelers will be issued I-94s during the admission process at the port of entry.
Where is the DLC on a GM 94?
Locate Data Link Connector (DLC), see image below. Turn Ignition switch to ON position. Count the flashes on the “ CHECK ENGINE ” or “ SERVICE ENGINE ” light. NOTE: Some 94 & 95 models do not have the B terminal. In which case a scanner is required.
Do you need a scanner for a GM 94?
NOTE: Some 94 & 95 models do not have the B terminal. In which case a scanner is required. NOTE: Some 94 & 95 models that DO have the A & B terminals still require a scanner. All vehicles after 96 are OBDII,and require a scanner to access them.